Search Documents

By B. P. Watson, T. J. Maphosa, D. P. Roberts, L. J. Gardner

The results of FLAC3D modelling on chromitite Upper Group 2 Reef pillars from the Bushveld Complex of South Africa are described. The model input parameters were determined from laboratory triaxial tests with post-failure measurements. These geomechanical tests were performed on rock materials within the pillars and the immediate pillar foundations. In the models, postfailure behaviour was simulated using the concept of cohesion softening. Models were built to determine the strength and behaviour of pillars with a width-to-height ratio of approximately two. The original research aimed to find a suitable depth below the surface where Impala Platinum Ltd could safely introduce crush pillars; however, the paper only describes the model results: the ideal depth of the crush pillar introduction is not discussed. The results of the modelling are compared with the PlatMine formula for peak pillar strength and with an underground instrumented pillar located elsewhere on the same reef. Some insight into the effects of grid size on strength is also provided. Further underground measurements are recommended to verify the model results

Sep 9, 2024

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By K. Dagdelen , S. K. A. Owusu

Uncertainty with regard to estimated grades and tonnages of a mineral deposit demands risk assessment in order to build investor confidence and attract the interest of other stakeholders in the success of a project. Uncertainties associated with Mineral Resource estimates can lead to unreliable production schedules and unpredictable cash flows. However, the techniques used in the mining industry to determine these uncertainties are inconsistent, because the important decisions taken in the process are solely dependent on the responsible Competent Person (CP), without limitations. This leads to disparities between different CPs’ results, using data-sets from the same drill-holes. The various standard codes for public disclosure provide guidelines and recommendations for the classification of Mineral Resources and Reserves but do not provide details on, for example, the amount of geological and geostatistical information needed to qualify for each category of Resources and Reserves. The parameters used to generate the classification categories are subjectively assumed by the responsible CP. In this paper we investigate the impacts of different CPs’ judgements on resource classification, using the same data-sets. The results underpin the need for the mining industry to develop a uniform Mineral Resources and Reserves classification framework that can minimize or avoid significant discrepancies that lead to potential misleading public disclosures.

Aug 8, 2024

The established shared laboratory facilities between the Departments of Metallurgy and Chemical Engineering of the Vaal Triangle Technikon and the University of Potchefstroom are already proving to be a great success.

Jan 1, 1992

By H. Ruthert

An understanding of wear in systems conveying solids is extremely important from the standpoints of design and economics. The lifetime of any bulk solids-handling system depends on the type of solids present and the operating parameters of the transportation system. The relationship between wear in backfill pipelines on South African gold mines and the transportation system's operating parameters is well understood. However, the effect of the transported solids on the pipe wear is less well understood, because of an inability to characterize particle sharpness. The sharpness of the particles, together with their size and hardness, is responsible for the aggressivity of particles, or their ability to cause damage and wear. This paper presents a novel method for the characterization of particle sharpness. The results presented rank particles according to the sharpness of their surfaces.

Jan 1, 1993

By J. Githiria, D. Wachira

The conventional truck and shovel haulage system has become expensive to operate in most mines due to current strict environmental conditions, increase in depth and size of open-pit mines, increase in labour costs, and fuel costs. These factors have motivated the search for alternative material haulage options in open-pit mines. In-pit crushing and conveying (IPCC) system has been regarded as a plausible alternative in material haulage systems. However, usage of IPCC has been limited to a few mines due to limited knowledge of IPCC performance, and other technical factors of the system. This paper investigates, and evaluates the productivity performance of four types of IPCC systems (fixed, semi-fixed, semi-mobile, and fully mobile IPCCs) using mine productivity index (MPi). Using a model developed by MATLAB, the MPi for the four systems is computed using input variables such as availability, utilisation, performance and number of trucks and shovels in a limestone quarry. The mine productivity index for fixed, semi-fixed, semi-mobile, and fully mobile IPCC is obtained as 67.13%, 69.02%, 70.52%, and 71.52% respectively. In conclusion, the fully mobile in-pit crushing and conveying system is the most appropriate IPCC in the quarry, due to its better productivity performance compared to the other three IPCC systems and the truck and shovel system currently in use.

Sep 1, 2021

By I. A. Mwamba

Titanium aluminide of composition Ti-47.5 at.% Al was prepared by melting titanium and aluminium of commercial purity with additions of precious metals of 0, 0.2, 1, 1.5 and 2 at.% content. The microstructure, hardness and oxidation properties were assessed. It was found that at 47.5 at.% Al, the microstructure of plain TiAl alloys was duplex, consisting of duplex lamellar grains and ? grains. The lamellar grains consisted of alternating lamellae of ? (TiAl) and a2 (Ti3Al), with overall aluminium content in the range of 43?47 at.%. The ? grains had a aluminium content above 50 at.%. The addition of precious metals to the TiAl alloy resulted in the formation of a new phase, with a high precious metal content, occurring mostly in the ? phase, without any major change to the microstructure. Increasing the amount of precious metals resulted in an increase of the new phase amount, at the expense of the ? phase. The hardness of the different alloys was around 300HV10. Overall, the research has shown that addition of precious metals to TiAl resulted in a slight increase in hardness and a significant improvement of the oxidation resistance. This shows that alloying TiAl with precious metals, at the addition levels investigated, does not alter the mechanical properties very much, but improves oxidation resistance.

Jan 1, 2012

By I. M. Morsi

The present study investigates the feasibility of using some materials as start-up slags for the extraction of magnesium metal from Egyptian dolomite ores by the Magnethermic technique. The reduction of roasted dolomite (dolime) takes place in a closed evacuated electric arc furnace (small Magnetherm reactor) using ferrosilicon as a reducing agent and liquid start-up slag as a reduction bath under an inert atmosphere. The operational parameters affecting the stabilization of the start-up slag composition and the extraction of magnesium such as reducing agent stoichiometry, reduction temperature, and time were investigated. The dolomitic charge was in the form of sintered briquettes. The charge was reduced under an argon atmosphere in the Magnetherm reactor for constant period and constant temperature. The results showed that the clinker can be used as a start-up slag for the magnethermic process. Also, the optimum conditions for the extraction process were found at 2XSi stoichiometry to give maximum reduction of 80% after 15 minutes reduction time at a temperature of 1550°C. XRD and XRF measurements were used to determine the phases present and the extent of reduction of magnesium, respectively. Keywords magnesium, dolomite ore, magnetherm, magnetherm reactor, silicothermic reduction.

Jun 1, 2013

By A. V. Z. Brink

This paper describes the development of a monitoring architecture that allows for continuous monitoring of the process of mining, the underground environment, the state of the rockmass and its response to mining. The system is based on an open standard and is non-propriety. It allows for dense sensor arrays in the workplace, wire less communication to the closest power line, and TCP/IP communication to a central server. Continuous monitoring and quantification of the appropriate parameters allows a mine to optimise its mine process; to dynamically access the safety and health risk to people and equipment; and to quantify exposure to potential heath hazards such as dust, gas or noise. Current application examples of continuous monitoring include an application to optimise drilling and blasting thought fragmentation monitoring; an application of wireless sensor network-based monitoring in to provide early detection of potential rockfalls; and a trail to continuously assess the gold grade at the shaft through correlation with radioactivity. It is unlikely that a single monitored parameter will provide adequate knowledge of the assessed risk or even an optimisation approach. Multiple parameters are being combined using cognitive science tools such as Bayesian theory and other statistical methods to improve the accuracy and relevance of, for example, risk quantification. The decision maker is not confronted with massive amounts of raw data but rather with a single knowledge statement such a probability of failure, a human physiological strain index or an optimisation index.

Jan 1, 2008

The annual General Meeting of the Branch was held in the St. Helena Club on Wednesday, 4th August, 1971 at 8.00 p.m. Mr N. A. Honnet (Immediate Past Chairman) was in the chair. There were also present Mr V. C. Robinson, President of the South African Institute of Mining and Metallurgy. Nine Fellows: Messrs J. R. F. Handley, C. J. Isaac, J. Lorenzon, J. M. Meyer, C. Mostert, D. A. Smith, S. L. S. Swart, I Thomas and R. G. Williams. Five members: Messrs R. Campbell, A. H. Edwards, K. Pearce, G. P. Rundle and R. B. Sutherland. Five graduates: Messrs J. E. Andrews, E. J. Shillaber, M. H. Smith, T. R. Stromsoe and D. J. van Niekerk. Two associates: Messrs A. Paschalides and D. S. Robinson. Eight visitors. Total present: Thirty-one. MINUTES OF THE PREVIOUS GENERAL MEETING As the minutes of the General Meeting held on the 16th June, 1971, had not been published in the Journal, the Chairman moved that the adoption and discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. The minutes of the General Meeting held on the 10th February, 1971, were taken as read. The adoption, which was proposed by Mr D. A. Smith and seconded by Mr J. M. Meyer, was carried unanimously. At Mr Honnet's request, Mr V. C. Robinson took the chair during the presentation of the Chairman's Annual Report. CHAIRMAN'S ANNUAL REPORT 1970/71 1970/71 Committee-Office Bearers: Chairman - J. N. Saunders Vice Chairman - G. Y. Nisbet Immediate Past Chairman- N. A. Honnet. Due to the sudden retirement of Mr J. N. Saunders, the committee, at a meeting on the 3rd February, 1971 elected Mr G. Y. Nisbet as Chairman with Mr J. M. Meyer as Vice Chairman. After the transfer of Mr Nisbet to C.D.M., the committee, as a meeting on the 12th May, 1971, decided that Mr Meyer hold the Chair in an acting capacity for the remainder of the year. Committee members: Messrs C. J. Isaac, J. G. Kirchener, L. O. W. Leimer, R. S. Pearson, I. G. Thomas and A. von Holdt. Transfers of several office bearers and committee members resulted in Messrs J. M. Meyer, D. N. Smith and G. C. J. Young being co-opted onto the committee.

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By F. Rosenblum, K. E. Water, J. A. Finch, S. Moon, Y. H. Tan

Previous work has shown that sulphide self-heating occurs in three distinct stages referred to as Stage A, Stage B and Stage C. In this paper the focus is on the transition from Stage A to Stage B, which occurs at ca. 100OC. Background literature hints that the transition corresponds to the transformation of the rhombic form of elemental sulphur to the more reactive monoclinic form that occurs at 96OC. A test apparatus is modified for adiabatic heating to track the transition. The results support this transformation of sulphur as being key to the transition, and the transition temperature is thus modified to 96OC. Variations in a sample’s response under adiabatic conditions are observed and possible reasons are discussed. Testing in adiabatic mode provides new insights into the sulphide self-heating process that complement the test designed to identify propensity to self-heat. Keywords: Self-heating; Stage A/Stage B; transition; rhombic/monoclinic elemental sulphur; adiabatic heating

Jan 1, 2020

By S. M. Brabyn

The wear in mild steel pipelines used to convey rod-milled waste backfill was determined and then compared with that obtained using a laboratory rig designed to simulate the wear condition in slurry pipelines. The relative importance of corrosion and abrasion was investigated under various conditions of water quality and particle size distribution. The laboratory rig was then used to evaluate other possible materials of construction for backfill pipelines. A preliminary assessment of the economic viability of pipelines made of alternative materials is included.

Jan 1, 1988

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012

By P. J. Bartlett, H. A. D. Kirsten

A two-dimensional numerical scheme for the simulation of the plastic stress-strain properties of rock, and the various components of rock reinforcement and shotcrete, was used to rigorously determine the characteristics of tunnel support under squeezing conditions. D-shaped tunnels varying in size from 2,8 to 6,5 m in height and width were considered. The four main mining stages in the BAS block cave on Premier Mine were simulated as alternative sets of field stresses. The rock reinforcement comprised 1,8 m long fully grouted rockbolts and 6,0 m long fully grouted cable anchors at various spacings, and of various tensile and bond strengths. Various thicknesses of shotcrete and footwall support configurations were also considered. It was found that shotcrete and rock reinforcement, owing to inherent differences in stiffness, do not function in unison. As monolithic application, shotcrete has an overriding avidity for the imposed loading and destructs itself unless of extraordinary thickness. Under squeezing conditions, it accordingly supports the excavation surface while the rock reinforcement contains on-going convergence. The loads in the various support components can be determined only by simulation of the shotcrete as a stress-relieved medium to represent its broken condition in the field. The loads in the rock reinforcement vary around a tunnel and are the largest in the sidewalls. The loads increase with an increase in tunnel dimensions, the increase in load in the sidewall due to an increase in height being larger than that in the hanging- and footwalls due to an increase in width. Depending on the strength of the rock, the loads in the rock reinforcement become prohibitively large beyond a certain size of tunnel. The reinforcement of footwall rock can be omitted without adversely affecting that in other walls, provided the tensile and bond strengths of the reinforcement are not limited. The resulting footwall heave may, however, result in undermining of the reinforcement in the adjoining walls. A relative depth of anchor of 1,37 provides adequate bond strength in the larger sizes of tunnel, whereas, in smaller tunnels, anchor length is determined by the allowable convergence. The lack of fun column grouting adversely affects the efficiency of rock reinforcement to a major extent. The loads in rock reinforcement are very sensitive to the strength of the rock. Owing to a lack in refinement and calculational rigour, empirical classification systems are an inappropriate means for the design of tunnel support in squeezing conditions and, as a result, grossly unclear-estimate the support requirements.

Jan 1, 1992

By N. J. Alderman, R. Haldenwang

Flumes are ubiquitous throughout the mining and minerals processing industries as well as being used in the polymer processing and pulp and paper industries. With the increased demand for the transport of highly concentrated slurries in rectangular open channels, there is an impetus for a better understanding of the role of rheology in flow hydraulics. Until recently, design of such channels has been based on either the Chézy or Manning equations used for modelling open channel flow of Newtonian fluids. This has been done for modelling turbulent flow of low concentrated slurries with some success. However, this is not the case for highly concentrated slurries where the flow in the channel is no longer turbulent. Unlike Newtonian fluids, work carried out on flow of pseudo-homogeneous, non-Newtonian fluids in open channels is somewhat limited. Moreover, these results have been published in a variety of sources. This paper attempts to give a critical review of the work carried out on Newtonian and non-Newtonian flow of pseudo-homogeneous non-settling slurries in rectangular open channels. A comparison is also made of the models based on power law, Bingham plastic and Herschel-Bulkley fluids for laminar and turbulent flow in rectangular open channels.

Jan 1, 2007

By D. J. Shields

The U.S. Bureau of Mines has developed a microcomputer-based mineral modelling system that enhances analytical capabilities of the agency. It draws upon the extensive data base previously developed for the Bureau's Availability studies. The model is first formulated as a generalized network flow optimization problem, the optimal flows from which are fed into a transportation algorithm. The goal of the modelling system is first to fulfill prespecified demand at the minimum opportunity cost and second to identify feasible, optimal trade patterns. The system facilitates the analysis of policy issues on a real-time basis and supports the Bureau's mission to assess mineral resources.

Jan 1, 1987

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By N. Sacks, N. B. S. Magagula, I. Botef

"Low-pressure cold gas dynamic spraying was used to deposit WC-4wt%Ni and WC-4wt%Ni-1wt%Mo coatings onto mild steel. Dense coatings with very low porosities were produced. No decarburization occurred during deposition and no deleterious phases were formed. The coatings were subjected to standardized material characterization tests, as well as slurry abrasion testing to assess their wear behaviour. The wear tests were conducted in synthetic minewater-silica slurries, while distilled watersilica slurries were used as a control. The hardness of the coatings, 512HV0.3 and 458HV0.3 for WC-4wt%Ni and WC-4wt%Ni-1wt%Mo respectively, are comparable to those achieved using high-temperature coating processes. The abrasion wear rates for both coatings were less than 5 mg/min and 10 mg/min in the distilled water-silica and synthetic mine water-silica slurries respectively. The approximately 50% increase in wear rate in the synthetic minewater slurry is attributed to a synergistic corrosive wear mechanism. The predominant wear mechanisms were identified as binder smearing and delamination, with carbide grain fracture and pull-out. IntroductionSlurry abrasion is a common phenomenon in mining operations, particularly in pipelines transporting, for example, sand-water slurries. This type of wear can cause pipeline fracture, shortened operational lifetimes, and impede pipeline efficiency. To reduce or limit abrasion, thermally sprayed tungsten-carbide-based coatings are often used as pipe linings (Kanchan et al., 2010). This is due to their attractive mechanical properties, which include high wear resistance, stiffness, hardness, compressive strength, and tensile strength. These properties are provided by the coating microstructure and composition, which is a blend of hard, wear-resistant tungsten carbide (WC) particles embedded in a fracture-tough metallic binder phase (Brookes, 1997). Cobalt (Co) is the most commonly used binder due to its excellent wetting of the WC phase and moderate mechanical properties; however, its application is limited to non-corrosive environments as it has a low corrosion and oxidation resistance (Andren, 2001). Nickel (Ni) may also be used as a binder, and has been shown to have superior oxidation and corrosion resistance, but in some applications may not have the required mechanical properties (Kim et al., 2006)."

Jan 1, 2016

By D. Pienaar, D. Stanton

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2006