Search Documents

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau of Mines, which conducts research on many of the complicated and frequently interrelated problems of extracting crude oil and natural gas from the ground, transporting them to market or to places for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because may of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau f Mines, which conducts research on many of the complicated and frequently interrelated problems f extracting crude oil and natural gas from the ground, transporting them to market or to daces for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because many of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By Robert F. Chaiken

Burnout Control is a process developed by the U.S. Bureau of Mines for accelerating the burning of wasted coal fires in situ, while at the same time controlling the heat and fumes produced. The Albright fIre project is a fIrst fIeld trial of Burnout Control as applied to a coal waste bank. An exhaust ventilation system was designed and constructed and then operated over a 1-year period at the site of an existing abandoned mine land fire near the town of Albright, WV. While predicted exhaust gas temperatures of 900° C and thermal power levels of 5 MW were achieved at 20-to 3O-in H20 vacuum levels, problems were encountered with engineering designs, equipment breakdown, and fuel-rich combustion that curtailed the time period of satisfactory operation. Effective afterburning of the exhaust gases (as they were drawn from the bank) corrected the problems associated with combustion stoichiometry and led to high thermal outputs. It is believed that with (1) improvements in engineering design and construction, (2) better control of the afterburning process, and (3) the use of conventional stack gas air-pollution controls, Burnout Control can be applied successfully to a coal waste bank fire.

Jan 1, 1991

The Bureau of Mines studied blast-produced ground vibration from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Direct measurements were made of ground-vibration-produced structure responses and damage in 76 homes for 219 production blasts. These results were combined with damage data from nine other blasting studies, including the three analyzed previously for Bureau of Mines Bulletin 656. Save levels of ground vibration from blasting range from 0.5 to 2.0 in/sec peak particle velocity for residential-type structures. The damage threshold values are functions of the frequencies of the vibration transmitted into the residences and the types of construction. Particularly serious are the low-frequency vibrations that exist in soft foundation materials and/or result from long blast-to-residence distances. These vibrations produce not only structure resonances (4 to 12 Hz for whole structures and 10 to 25 Hz for mid walls) but also excessive levels of displacement and strain. Threshold damage was defined as the occurrence of cosmetic damage; that is, the most superficial interior cracking of the type that develops in all homes independent of blasting. Homes with plastered interior walls are more susceptible to blast-produced cracking then modern gypsum wallboard; the latter are adequately protected by a minimum particle velocity of approximately 0.75 in/ sec for frequencies below 40 Hz. Structure response amplification factors were measured; typical values were 1.5 for structures as a whole (racking) and 4 for midwalls, at their respective resonance frequencies. For blast vibrations above 40 Hz, all amplification factors for frame residential structures were less than unity. The human response and annoyance problem from ground vibration is aggravated by wall rattling, secondary noises, and the presence of airblast. Approximately 5 to 10 pct of the neighbors will judge peak particle velocity levels of 0.5 to 0.75 in/sec as "less than acceptable" (i.e., unacceptable) based on direct reactions to the vibration. Even lower levels cause psychological response problems, and thus social, economic, and public relations factors become critical for continued blasting.

Jan 1, 1980

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mine operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also Investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result in reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

Mine waste and mine reclamation are topics of major interest to the mining industry, the government and the general public. This publication and its companion volume are the proceedings of a conference held in Pittsburgh, April 19-21, 1988. There were nine sessions (50 papers) that dealt with the geochemistry, hydrology and problems of mine waste and mine water, especially acid mine drainage. These comprise Volume 1. The nine sessions (43 papers) that dealt with reclamation and restoration of disturbed lands, as well as related policy issues, are included in volume 2. Volume 2 also contains the ten papers that pertained to control of subsidence and mine fires at abandoned mines. Poster session presentations are, in general, represented by abstracts; these have been placed in the back of both volumes.

Jan 1, 1988

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By C. F. McCarroll

The effectiveness of an industry's safety activities can be gaged best by the accident records of that industry. In an effort to gage conditions in the petroleum industry, and with the objective of helping to reduce the number of accidents in it, the Bureau of Mines from time to time has tabulated, analyzed, and published pertinent statistical information.3/. These reports have dealt with distribution, causes, and costs and related phases of accidents for various and collective divisions of the petroleum industry in several sections of the country. This type of study aids the personnel of the Bureau in planning the course of its activities in accident-prevention work and gives useful data to persons engaged or interested in the promotion of safety in the petroleum industry, which will aid them in their efforts to reduce the number and severity of accidents. A majority of petroleum operators and "service? contractors have acknowledged their responsibility to provide their employees with safe working conditions and to their stockholders for greater economic value of invested capital by establishing safety divisions within their respective organizations. Such divisions have a primary duty, namely, to see that properly designed and guarded machinery and working equipment are furnished the employees and that they are trained in the safest practical methods of performing their work. Some companies and individual operators, however, have shown little or

Jan 1, 1939

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By Jerry B. F. Champlin

The successful injection of liquids into subsurface permeable formations for production stimulation, storage, or waste disposal requires a rapid, precise, and accurate method of determining the permeability of porous solids. This report describes a method and apparatus, developed by the Bureau of Mines, that use the principle of specific-volume permeametry. Calibration of the apparatus over a wide range of permeabilities and standardization of several apparatus constants have eliminated many of the tedious calculations and problems of manipulation common to some other methods. Improvements in reproducibility and accuracy have resulted from reducing experimental measurements to one parameter--time. Specific permeabilities of reservoir rock samples are determined directly from a chart that relates elapsed time to a permeability equivalent to that determined by bubble-tube measurements.

Jan 1, 1962

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7510 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Utilization. 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. Oil and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1963

By Sidney Katell

This report covers the period January 1962 through December 1962; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fourth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load evolved in the preparation shared equally. Tile abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from tile following sources:

Jan 1, 1963

By D. A. Reynolds, J. D. Davis

"INTRODUDTION Investigations by the Bureau of Mines have shown that the carbonizing properties of splint and bright coals may differ greatly. In a study of 55 coal columns selected from representative coals of the Appalachian region, Sprunk and coworkers 10/ compared various chemical and physical properties of splint and associated bright coals. Carbonization tests in the Fischer retort at 932°F. (500°C.) showed that, except for bright coals of high oxygen content, the coke residue from bright coal was much more swollen and cellular than that from splint. ·with one exception, agglutinating values determined by the Bureau of Mines test, were lower for splint than for associated bright coal.Because sorting of coal in quantity is tedious and time-consuming, separate types have not been carbonized by the Bureau of Mines-American Gas Association (BM-AGA) test, which requires 85- to 200 pound charges. However, this method has been used to determine the carbonizing properties of samples 0f bed layers that are composed largely of either splint or bright coal.4/ In these earlier tests, which were made at high temperatures on layer samples from the Elkhorn bed, Letcher County, Ky., the splint coal yielded more coke than the bright coal, and this coke was slightly stronger than that from the bright coal. The cokes from samples with large proportions of bright coal were more cellular or porous, as were the low-temperature cokes obtained from carbonization of separated samples of bright coal in the Fischer retort."

Apr 1, 1944

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974