Search Documents

By P. G. Pigott

This investigation by the Bureau of Mines demonstrated that building bricks can be produced by the steam-curing process from various types of industrial mineral wastes. Wastes, utilized to produce bricks, consisted of copper mill tailings, roofing granule fines, asbestos fines, and zinc mill tailings. Bonding of the wastes with either Ca(OH)2 or portland cement resulted in building bricks that met ASTM specification C73-67 for grade SW and MW bricks when evaluated in accordance with ASTM designation C67-66 on sampling and testing of brick. An economic evaluation of the process indicates the total operating cost per 1,000 bricks is about $36.

Jan 1, 1974

By T. H. Dubaniewicz, J. E. Chilton

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 1992

By Edward D. Thimons, Jay F. Colinet

NIOSH conducted a strategic planning effort to identify those areas in mining with the greatest research needs. Data analysis and stakeholder input identified the need to reduce worker exposure to respirable crystalline silica dust as a high priority area. MSHA dust sampling data were analyzed to target the mining commodities and occupations with the greatest percentage of samples containing silica above compliance levels. In response, the Pittsburgh Research Laboratory (PRL) has implemented a multi-faceted research program to improve silica dust control for these problematic commodities and occupations. A review of silica compliance trends, PRL silica research programs, and recent control technology developments are provided here.

By F. N. Kissell

The Bureau of Mines has successfully used sulfur hexafluoride (SF6) as a tracer gas to measure mine air flows under conditions where conventional methods have failed. SF6 was employed experimentally to measure accurately recirculation of return into intake air caused by leakage through an old stoped area, to check for potential leakage from an adjacent mine, to trace 10,000 cfm of “lost” air from an intake airway, and to measure transit air time through uranium mines. It proved useful as a means of accurately measuring airflow volumes in airways of large cross section and very low flow velocity, and in determining the recirculation resulting from underground cooling plants.

Jan 1, 1974

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

CESIUM metal production increased sharply in 1963. Domestic Production.--Cesium metal was produced by The Dow Chemical Co., Midland, Mich., MSA. Research Corp., Callery, Pa., and by Penn Rare Metals, Inc., Revere, Pa. American Potash & Chemical Corp., Trona, Calif., produced some combined cesium and rubidium. This company, Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., produced various cesium compounds. Complete production data on cesium and rubidium and their compounds were not available for publication. Consumption and Uses.-Substantially more pollucite was consumed to produce cesium metal and compounds in 1963 than in 1962 but the overall consumption of pollucite continued to be small.

Jan 1, 1964

By Anthony T. Lannacchione, Donald G. Puglio

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By Kathleen J. D?Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By George S. Rice, O. P. Hood

The need of protecting mines from the danger of inflow of natural gas from neighboring wells has become more apparent each year since it was found that oil and gas underlie the productive coal measures of Pennsylvania, West Virginia, Ohio, Indiana, Illinois, Kansas, Oklahoma, Colorado, and Wyoming, and, to some extent, the coal measures of other States. The proximity of the known gas and oil areas in the United States to the coal fields and the manner in which the fields overlap in certain States are shown in the map comprising the frontispiece (Pl. I). As the result of many requests received from various sources a conference to consider the protective measures necessary to insure the safety of mining operations in gas and oil fields was called by the Director of the Bureau of Mines to assemble in Pittsburgh, Pa., Feb- ruary 7 and 8, 1913. To this conference were invited a considerable number of gas-well, oil-well, and coal-mine operators within conven- ient distance from Pittsburgh, as well as State geologists and State mine inspectors from a distance. Gas and oil wells are also found near other kinds of mines, such as shale and limestone mines in western Pennsylvania, but these cases are so few that for this and other reasons it was deemed best to con- fine the present inquiry to the consideration of the questions involved in connection with coal mines. It was also not thought advisable to consider the protection of mines from other kinds of bore holes than those for gas and oil, such as coal-prospecting holes, drilled either with churn or diamond drills, or salt wells and artesian wells, because little trouble has been ex- perienced in mining operations from these classes of wells. There- fore the following papers and discussions concern almost entirely the following relations between coal mines and gas and oil wells: (1) Protection of coal mines froin gas and oil wells penetrating -through: (a) Open workings; (b) inaccessible spaces or goaves; (c) pillars, or coal which may be left as pillars. (2) The manner of drilling gas and oil wells passing through workable coal beds so as to provide protection for future mining. The preliminary inquiries of the engineers of the bureau had dis- closed that there was no uniformity in the methods of protecting mines against the leakage of gas from wells, that thousands of wells in coal fields are abandoned yearly without adequate plugging, and without surveys or records being kept to show the location of the holes, from which the casings are generally pulled. According to the State geologist of Pennsylvania, as many as 3,000 wells are being drilled annually in Pennsylvania, 2,000 of these holes being aban- doned within a single year. It is such unplugged, uncharted wells that are the greatest menace in mining. The quantity of gas that the wells produce, although not sufficient to be commercially avail-

Jan 1, 1913

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

By A. J. Hudson, M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 9 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY; PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2;1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AROUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11;1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS 0F THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By Erica E. Hall, Robert H. Peters, Charles Vaught, Jon C. Volkwein

Coal workers’ pneumoconiosis is the leading cause of death due to occupational illness among U.S. coal miners. This disease is caused by miners’ exposure to excessive levels of respirable coal mine dust. A personal dust monitor (PDM) has recently been developed to provide near real-time feedback to miners regarding the level of respirable coal dust in the air they breathe. The main objective of this report is to document coal miners’ reactions to this device and how they make use of the information it provides. It summarizes a field study by the National Institute for Occupational Safety and Health that documented the opinions of 30 miners at 4 underground coal mines concerning the use of PDMs.

Jan 2, 2008

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By T. Estelle Gardner

The Bureau of Mines made enthalpy measurements on sodium bromide and sodium iodide in the temperature range 400° to 1,200° K using an ice calorimeter. Equations representing enthalpy as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate smooth values of heat capacity, enthalpy, and entropy at 50° K intervals from the ice point to 1,200° K. The melting point determined for sodium bromide was 1,020° K; the melting point of sodium iodide was 934° K. The heats of fusion of sodium bromide and sodium iodide were calculated to be 6,270 and 5,680 cal/mole, respectively.

Jan 1, 1967

By Lloyd A. Morley, Alan M. Christman

This report was prepared by the Department of Mineral Engineering, The Pennsylvania State University, University Park, Pennsylvania under USBM Grant Number G0155102. The grant was initiated under the Metal and Nonmetal Health and Safety Research Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Mr. Roger L. King acting as the Technical Project Officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period February 1, 1975 to July 31, 1976. This report was submitted by the authors on August 31, 1976.

Jan 1, 1976

By Alan H. Goode

As part of the Bureau of Mines program to broaden utilization of abundant low-quality mineral materials, the Tuscaloosa Metallurgy Research Laboratory conducted beneficiation studies on two Alabama clays. The main purpose of these studies was to develop improved plasticity and green strength in both clays and compare these improved properties with those of a typical ball clay. Whiteness of the clays was also considered. The results indicated that by adjusting the pH of the kaolin to approximately 9, a substitute for ball clay could be obtained. The investigation also showed that by a combination of attrition grinding and sodium dithionite leaching to remove iron, the underclay could be upgraded to a ball clay material.

Jan 1, 1975

By L. H. Adami

Heats of formation were obtained for four anhydrous crystalline sodium borates by hydrochloric acid solution calorimetry. The heats of formation at 298.15° K from the elements are NAB02, -233.2 ±0.6 kcal/mole; Na2B07, -786.4 ±1.0 kcal/mole; NaB305, -549.9 ±0.8 kcal/mole; and Na2B6013, -1,412.5 ±2.0 kcal/mole, The heats of formation from the constituent oxides are NaB02, -31.5 ±0.8 kcal/mole; Na2B407, -78.8 ±1.3 kcal/mole; NaB305, -44.1 ±0.8 kcal/mole; and Na2B8013, -96.7 ±1.5 kcal/mole.

Jan 1, 1968

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of selected ingredients employed in the formulation and manufacture of conveyor belts. This work was done to supplement similar studies of samples from finished conveyor belts and thus provide basic data for correlation of the potential toxic behavior of a finished belt with that of the individual ingredients. This report covers the study of (1) basic polymers (styrene-butadiene, neoprene), (2) reinforcing fibers (Nylon 6,6, Dacron, viscose rayon), (3) flame-retardant plasticizers (tritolyl phosphate-isomeric mixture, tri-p-tolyl phosphate, tributyl phosphate, tris (dichloropropyl) phosphate), (4) plasticizers (diphenylphtha1ate, di-(2-ethylhexyl) sebacate), and (5) a vulcanization accelerator (2-mercaptobenzothiazole).

Jan 1, 1977

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method, Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out- crop will emit low levels of methane gas.

Jan 1, 1977