Search Documents

By Andrew J. Fergus

A study of the flotation characteristics of columbium-tantalum minerals was made by contact-angle and microflotation methods, and the findings were confirmed by flotation of two natural ores. In the contact-angle study conditions for collection of columbite, pyrochlore, and tantalite were determined for (1) sodium oleate with a sulfonate; (2) sodium isooctyl phosphate; (3) a short-chain primary amine; (4) a long-chain primary amine; and (5) a quaternary amine. These conditions were confirmed in microflotation tests. Information about collector action on common gangue minerals was also obtained by these two methods. In batch flotation tests on a pyrochlore ore and a columbite ore, it was demonstrated that collectors selected on the basis of contact-angle and micro-flotation studies would float columbium minerals from a complex natural ore. However, multiple cleaner and scavenger flotation steps will be necessary to produce commercial concentrates. From a pyrochlore ore containing 0.54 percent Cb2O5, a 44.4 percent Cb2O5 concentrate was made containing 36.4 percent of the total Cb2O5. For a columbite are the corresponding values were: 4.35, 54.6, and 67.1 percent. During the batch flotation study, wetting agents were found to aid in the gangue-ore mineral separations.

Jan 1, 1968

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing mischmetal (MM), cobalt, copper, magnesium, and iron for use in permanent magnets in place of the scarce samarium-cobalt alloys. The magnetic properties of MM-Co, MM-Co-Cu, MM-Co-Cu-Mg, and MM-Co-Cu-Fe-Mg alloys were evaluated. Magnets were fabricated by powder metallurgy consisting of arc-melting the metals, crushing and grinding the resultant alloys, alining and compacting the powder, and sintering the compacts. Magnetic values of MHc = 4.7 kOe, BHc = 4.07 kOe, Br = 6.81 kG, and (BH)max = 10.0 MGOe were obtained with a MM-Co alloy containing 36±0.5 wt-pct MM. By substituting copper and magnesium for part of the cobalt, the values for MHc and BHc were increased to 29.0 kOe and 5.89 kOe, respectively. This intrinsic coercivity value exceeded that of Sm-Co alloy obtained in our laboratory. The addition of iron to MM-Co-Cu-Mg alloys resulted in an increase of Br to 6.90 kG and (BH)max to 10.3 MGOe. Copper and magnesium contents of these alloys were optimized to obtain maximum values of MHc.

Jan 1, 1981

By J. H. Perry, D. W. Houseknecth, C. A. Kertis, A. T. Iannacchione

Major problems facing the development of coal and gas resources of the Hartshorne Coalbeds include the complex distribution of minable and unminable coal, high methane content and bed pressure, faulting, variations in degree of dip, presence of natural gas fields in associated sandstones, and legal problems, caused by local geologic characteris- tics, in identifying gas origin. This Bureau of Mines study provides pertinent geologic information for long-range planning of subsurface coal and gas production from the Hartshorne Coalbeds. Pittsburg, Coal, Hughes, and Atoka Counties, OK, have approximately 1 billion metric tons (1.1 billion short tons) of Hartshorne coal in place. The methane resource of Hartshorne Coalbeds is estimated at 9.2 billion m3 (325 billion ft3) and varies with overburden and rank, These estimates were compiled from gas well density logs, coal-core data, out- crop measurements, abandoned mine maps, and the literature. The Hartshorne Coalbeds represent a valuable coal and gas resource which at present is contributing nothing to coal and gas production. This report discusses potential problems and serves as a reference for future exploration and development work. Recognition of these potential geologically related problems prior to development of this basin will reduce hazards and allow for an economic recovery of these resources.

Jan 1, 1983

By Iam Pou Ng

Combustion aerosols consist mainly of elemental and organic carbon (EC and OC). Since EC strongly absorbs light and thus affects atmospheric visibility and radiation balance, there is great interest in its measurement. To this end, the National Institute for Occupational Safety and Health (NIOSH) published a standard method to determine the mass of EC and OC on filter samples. Another common method of measuring carbon in aerosols is the aethalometer, which uses light extinction to measure "black carbon" or BC, which is considered to approximate EC. A third method sometimes used for estimating carbon in submicron combustion aerosols, is to measure particle size distributions using a scanning mobility particle sizer (SMPS) and calculate mass using the assumptions that the particles are spherical, carbonaceous and of known density. With an eye toward evaluating the use of these methods for measuring carbon in freshly emitted diesel aerosols, the objective of this paper is to compare the results among these methods and to investigate the role of OC when measuring the mass concentration of elemental carbon (or black carbon) in aerosols emitted by a medium-duty Diesel engine. Results indicate that the aethalometer response correlates well with the data from filter samples (R2 = 0.99), with a very slight positive interference at high levels of OC.

Jan 1, 2008

By Joseph S. Coffman

The Bureau of Mines investigated the availability of barite (BaSO4) from 35 U.S. and 41 non-U.S. mines and deposits in 17 market economy countries (MEC's). This evaluation assesses the availability of mud-grade barite, and concentrates consumed by the chemicals and fillers industries. The demonstrated resources defined in this analysis totaled 130 million metric tons (Mmt) of barite (contained BaSO4), yielding a potential 115 Mmt of recoverable barite concentrates. At the 1984 MEC production rate, the evaluated resources would last about 30 yr; however, this would include production costs of up to $100/mt concentrate. An average price needed to cover all costs of production over the life of each operation was determined for both mud-grade and chemical- and filler-grade barite products. Including a 0-pct discounted-cash-flow rate of return (DCFROR), regional weighted- average total production cost ranged from $38/mt for barite concentrates in Asia to $71/mt for U.S. operations. Transportation costs have the greatest impact, contributing up to 60 pct of the total cost of production. Rail transportation costs from the mines to U.S. markets are generally significantly higher than ocean shipping rates on imports.

Jan 1, 1986

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945

By R. V. Ramani, C. B. Manula, A. Owili-Eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMRC, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. These applications were developed initially as a part of the instructional material for the course Mng 422, "Mine Ventilation and Air Conditioning" at the Department of Mineral Engineering, The Pennsylvania State University. This ventilation simulator was developed under contract from the Department of Environmental Resources, formerly the Department of Mines and Mineral Industries, Commonwealth of Pennsylvania.

Jan 1, 1975

The generally disappointing results obtained in the present study, together with the high material costs involved, preclude any general recommendation for a continuation of the work. One recommendation arises, however, from some observations on the application of latex to spoil banks. It was found that dilute latex used on a slope of spoil bank material at an application rate of 400 lbs per acre (dry basis) stabilized the soil and made it much more resistant to washout by rainfall. It is recommended that a study be conducted to use latex for temporary stabilization and/or sealing of spoil banks before and during reclamation procedures, on coal slurry ponds and coal refuse piles.

Jan 1, 1972

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Twenty-five years ago, the former U.S. Bureau of Mines funded a research project aimed at developing the enabling technology for incipient failure prediction in electric power system components as a means of reducing the injuries and fatalities that sometimes occur when equipment malfunctions. Over the ensuing years, interest in this has waxed and waned, but recently interest has been growing for both civilian and military applications. This paper addresses the level of turn-to-turn insulation deterioration that can be resolved using an on-line monitoring technique. The detection of turn-to-turn defects is especially important because they are believed to represent the beginning stage of most motor winding failures.

By Dorsey A. Lyon, Robert M. Keeney

In the inquiries and investigations that the Bureau of Mines is making with a view to increasing safety, efficiency, and economic development in the metallurgical industries, the application of elec- tricity to various processes, and especially to those in the manu- facture of iron and steel, is being given attention. Some results of the work already done are presented in this bulletin, which gives a historical review of the development of electric furnaces for making iron and steel, and discusses the problems that remain to be solved in the use of electric furnaces for the smelting of iron ores and the production of pig iron at a profit on a commercial scale.

Jan 1, 1916

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By Ronald D. Hill, Elmore C. Grim

The goal of blasting is to get maximum fragmentation of the consolidated material in the overburden with optimum drilling and blasting cost. The amount of fragmentation required is determined by the stripping unit to be used In overburden removal. Many coal seams must also be broken by blasting; this is conducted before coal removal. There are environmental factors as well as due regard for public safety, health, and welfare that must be considered in choosing the blasting plan. The blasting plan should be made during preplanning and is based on data from the overburden cores. Analysis of the data will help In determining the kind of drilling equipment and bit types that will be needed for overburden preparation.

Jan 1, 1974

Effective in the 1987 Minerals Yearbook, the following changes have been made: "Asphalt" has been deleted; "Greenland" is included in the "Potash" chapter; "Meerschaum" is included in the "Clays" chapter; and "Staurolite" is included in the "Abrasive Materials" chapter. QUARTZ CRYSTAL Cultured quartz crystal production increased significantly in 198?, following 2 years of reduced production. Consumption of domestic lascas as feedstock for cultured quartz crystal increased. Imports of lascas from Brazil also increased. Although no lascas was mined in the United States during the year, the domestic producer supplied material to consumers from company stockpiles. Specimen-quality natural quartz was very much in demand; quartz crystal for this application is discussed in the Gem Stone chapter.

Jan 1, 1989

By Ivette E. Torres

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom (London Metal Exchange) has been continued this year in tables 22 and 23. Time constraints have prohibited preparation of other price information that has appeared in this study in previous years. Users are urged to consult the 1993 U. S. Bureau of Mines publication Metal Prices in the United States through 1992, which gives an analysis of historical price series and trends, or the 1993 edition of Mineral Commodity Summaries for current U.S. prices on non fuel commodities, and to utilize U.S. Department of Energy sources for information on fuel material costs.

Jan 1, 1994

By E. G. King

This paper reports measurements of low-temperature heat capacities and entropies at 298.15° K. of two copper ferrites (CUFe204 and CU0.75Fe2.2504). These substances, which occur in copper-smelting slags, have not been sujected to any previous direct thermodynamic investigation. The two copper ferrites are spinel minerals of the variate class. In previous investigations similar data were obtained for 13 other spinel minerals -7 of the normal class and 6 of the variate class. The entropies at 298.15° K. of these minerals have been compiled and revised as necessary in the light of present knowledge regarding structural randomness; entropy values, recommended for use in thermodynamic calculations, are listed.

Jan 1, 1959

By Steve Iverson, Jeffrey C. Johnson, Henry Rodriguez, Rene Rodriguez, Michael Lhamond

To reduce fatalities resulting from personnel falling into voids formed above feeders in coal piles, the National Institute for Occupational Safety and Health at the Spokane Research Laboratory established a project to monitor coal surge piles to detect the formation of voids. A resistivity imaging method has been developed by GECOH Exploration, of Lexington, KY, in which a geophysical technique known as vertical electrical sounding (VES) is used to scan for these voids. VES operates by measuring the electrical field produced by a current in the ground at the bottom of the coal pile. This paper summarizes the results obtained from a field-scale test and shows that mapping voids within a coal pile is possible.

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968