Search Documents

By Thomas J. Peters

The U.S. Bureau of Mines studied the 63,9SS-acre Hanson Lakes study area, including the Ten Mile-East and part of the Ten-Mile West RARE II areas, plus additional acreage, all proposed at times for Wilderness designation. The study was part of a Idaho Land Assessment Program with the Idaho Geological Survey and the U.S. Geological Survey, to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The area is at the north end of the rugged Sawtooth Range and includes parts of the Sawtooth National Recreation Area which is closed to mineral location. The Copper Mountain. Elk Mountain, and Observation Peak mineralized areas are in the study area, but only Copper Mountain is open to claim location. It is on the trans-Challis fault zone and contains Tertiary granite which is favorable for mineral deposits of gold, beryllium, niobium, REE (rare-earth elements), tin, molybdenum, copper, silver, and lead. Identified resources are 1.9 million tons of flake graphite at Elk Mountain, but much more graphite occurs in the vicinity REE occurs in 18 black sand placer sites along the lower reaches of study area streams just outside the study area, on Cape Horn Creek, Marsh Creek, and lower Valley Creek flood plains, and at one hydrothermal site near Observation Peak. Hydrothermal REE is commonly low in? by-product thorium. a radioactive disposal problem. Many advanced REE applications enhance the quality of life, and future uses in superconductivity may reduce energy consumption. Seventeen lode, one geothermal, and 11 placer prospects were examined. Workings totaled about 20 adits, one shaft, several open cuts, and numerous small pits. Approximately 500 mining claims have been located or relocated in the study area, including a 200-claim block for disseminated molybdenum.

Jan 1, 1992

By Thomas V. Falkie, R. Venkataramani

The method of analysis was to test a large model containing potentially significant variables and on the basis of the results obtained, to reduce the model to one containing only the essential significant variables. This stepwise procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Data Preparation A majority of the variables measured were continuous over a specific range of values; for example, the variable "Width Ratio" varied in practice from 0.25 to 1.00. However, "dummy" values were assigned to certain operational variables in order that these varia¬bles would have numerical expression. The following variables were described in this manner. Variable "Dummy" Value x3: Development/Pillaring 0, if pillar extraction was being done 1, if development mining was being done x4: Boxcut/Open Cut 0, if a box cut was being made 1, if an open cut was being made The variables under consideration are represented symbolically as follows: Y: Loading rate (tons per minuts): TONS/MIN x1: Ratio, width of cut/width of cutter: WDRATIO x2: Ratio, height of cut/diameter of cutter: HTRATIO x3: Development or pillaring: D/P

Jan 1, 1972

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By C. A. Komar

Hardness, tensile strength, and impact toughness of dry and brine-saturated sandstone specimens were measured at ambient, cryogenic, and elevated temperatures as a measure of the relative stability of reservoir rocks for subsurface disposal of liquid wastes. Hardness measurements were inconclusive. Tensile strength and impact toughness were significantly higher at -320° F than at ambient temperature, but were relatively unaffected at 700° F. Impact toughness was reduced by subjecting the specimens to three cycles of rapid temperature changes (thermal shock) over a 1,000° F range. Tensile strength of brine-saturated sandstone was less than that of dry sandstone. Based on results of the tests, reservoir sandstone likely would be stable if exposed to extreme temperatures of liquid wastes, although rapid changes in waste temperatures should be avoided.

Jan 1, 1971

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By C. M. Mason

Mechanical mining produces large quantities of very fine coal dust called float dust. The associated increase in hazard requires a reexamination of the Bureau of Mines method of evaluating the incendivity of explosives in coal dust-gas-air mixtures. A technique recently developed by Bureau of Mines laboratories for evaluating the incendivity of explosives in coal dust-air mixtures was applied, with modifications, to coal dust-air-natural gas mixtures. A series of permissible explosives were evaluated by this modified technique. Results indicate that the modified technique could be the basis of a more discriminatory procedure than that presently in use.

Jan 1, 1968

By R. L. Grayson, W. E. Wallace, J. W. Stephens, M. D. Attfield, P. S. Brower, V. Vallyathan, M. J. Keane, J. C. Harrison

Pure respirable quartz is a known pathogenic agent for lung disease. However, for mixed dusts, neither mineralogical nor in vitro cytotoxicity assays unequivocally predict the contribution of quartz to their pathogenic potential.First, although Coal Workers' Pneumoconiosis (CWP) and Progressive Massive Fibrosis (PMF) prevalence have been found to correlate with total respirable coal mine dust exposure, and with coal rank (Attfield and Morring, 1992), epidemiological studies generally have not found the quartz component of coal mine dust as measured by X-ray diffraction or infrared spectroscopy (each of which essentially measures the mass-percent quartz in a bulk sample) to be clear predictors of CWP prevalence or incidence (Walton et al., 1971). Second, the properties which distinguish the extreme fibrogenic potential of quartz are not revealed by conventional in vitro bioassay comparison with other silicate mineral dusts. As an example, quartz and kaolin (aluminosilicate) clay in vitro cytotoxicities are comparable for lavaged primary pulmonary macrophages.The studies discussed here address these two anomalies from a general hypothesis that the pathogenic activity of respired quartz particles is associated with properties of, and interactions with, the particle surfaces. One factor in the expression of toxic activity by a particle surface is the biological availability of that surface. Anomalous lack of correlation of disease prevalence with mass percent quartz in exposures to some mixed composition respirable-sized dusts suggests that individual particle surface features, invisible by bulk sample mass analysis, may alter the biological availability of a fraction of quartz particles in a dust. For pure-surfaced mineral particles, the comparably strong prompt membranolytic activities of quartz and kaolin in vitro suggest that upon deposition of such particles in the lung there must be other interactions with particle surfaces which distinguish quartz. This might be due to toxic surface-associated sites specific to silica, or to interactions of other sites on other mineral particles which affect the biological availability of their toxic functional groups. For example, alurninol groups on clays affect the availability or activity of adjacent silanol groups. Surface activities which distinguish quartz pathogenici ty might be manifest in one or more of the sequential interactions upon deposition in the lung; first with the pulmonary surfactant system, then with extracellular and phagolysosomal enzymatic digestive processes, or with subsequent cytotoxic processes.

Dec 1, 1995

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today's environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Black Butte RARE (I area during the summer of 1981. The study area encompasses 17,800 acres [27.8 sq mi (7,233 ha)] along the course of the Black Butte River, 13 mi (22 km) southeast of Covello, California. No mineral deposits were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese, chromium, and nickel. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

Determine the dust reduction capabilities of various bag valves available to the minerals processing industry. The Problem Many different types of ground mineral products are packaged into 50-and 100-lb paper bags. Although bag technology is continually improving, dust contamination from bags still remains a significant problem for workers. The greatest source of dust is the bag filling valve. Ideally, the bag filling valve should close after it fills the bag with the ground mineral product. However, the valve usually fails to close properly since some mineral product gets trapped inside the valve during filling and ejection. As a result, when the bag has been filled and falls from the fill station, a rooster-tail of product is discharged from the bag valve. As the bag hits the conveyor belt, additional product discharges from the bag valve. The dust from these sources contaminates the air inspired by the workers filling the bags as well as the work area. Dust also clings to the outside of the bag, contaminating the pallet loading station. Because the various commercial bag valves are composed of different materials, a dust analysis was performed on five of these valves to determine their dust reduction capabilities. The five valves analyzed were: standard paper, polyethylene, extended polyethylene, double trap, and foam.

Jan 1, 1986

By N. A. Gokcen

Equilibrium partial pressures of gaseous HCl and H2O over aqueous binary and ternary solutions of HCl and AICls were calculated or estimated in the range of 20° to 110° C, and up to saturation with AlC13?6H2O. The results were extended to solutions containing less than 10 wt-pct FeCl3 by assuming that FeCl3 and AIC13 are equivalent on the molar basis, since both salts have trivalent cations with a cammon anion. The ionic activity coefficient of HCl and the equilibrium constant for dissolution of gaseous HCl were also computed. This research is part of the effort by the Bureau of Mines, U.S. Department of the Interior, to provide thermodynamic data to expand the technology base relevant to the extraction of alumina from nonbauxitic domestic raw materials.

Jan 1, 1980

By J. Grumer

Nine dust and gaseous inhibitors of propagating coal dust-air flames (lean, stoichiometric, and rich) were evaluated in a newly developed 15-cm-id, 3.6-meter-long instrumented flame duct, under conditions such that wall quenching was virtually absent and the dust concentration was temporally and spacially uniform to within about t5 percent. Listed roughly in order of increasing efficiency, the inhibitors evaluated were rock dust (calcium carbonate), powdered oyster shells (calcium carbonate), Halon 1301 (trifluorobromomethane), Halon 1211 (difluorochlorobromomethane), sodium chloride, Super-K (potassium chloride), regular-grade fire extinguishant powder (sodium bicarbonate), Purple-K (potassium bicarbonate), and Monnex (potassium bicarbonate combined with urea). Experiments were extended to clouds containing 1 and 2 volume-percent of methane. The inhibition of lean, stoichiometric, and rich methane-air flames without coal dust was also examined in a few instances; results agreed with those obtained for coal dust-air flames.

Jan 1, 1971

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By John C. Holtz

The Bureau of Mines studied air contamination caused by diesel exhaust in a 10,000-ft ventilated tunnel. Sequential air samples were taken at the ends and middle of the tunnel during an operating cycle. Observed and calculated results for carbon dioxide, carbon monoxide, and nitrogen oxides were essentially in agreement. Nitrogen dioxide was present only in trace amounts. It was found that contamination was related to the volume of ventilating air, the number of haulage trips, train speed, and engine load.

Jan 1, 1968

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 9, 1984

By Robert Blickensderfer

Equipment and procedure for the continuous roll bonding of metal strips are described. The reels, mill rolls, and furnace were located within a vacuum chamber capable of operation at a residual gas pressure of 1 x 10-4 to 1 x 10-5 torr. Several metals were successfully clad at rolling temperatures of 930° to 1,050° C in lengths up to 120 ft. The bimetals that were clad included stainless steel to carbon steel, molybdenum and nickel to stainless steel and carbon steel, and titanium to carbon steel. Bend tests of bond integrity are described, and microstructures of the interfaces are presented. The amounts of brittle intermetallic phases formed at the interface are minimized by this cladding method.

Jan 1, 1980

By Kenneth C. Stewart

Eight brands (three samples of each kind) of commercially available audio-dosimeters were performance-tested. Each unit was placed in an anechoic chamber and subjected to various acoustic signals to measure its A-weighting response and overall integration accuracy. All units met the A-weighting tolerance for type II sould level meters, and six brands were within the Bureau I s overall accuracy requirements of ±2 dbA referred to input.

Jan 1, 1974