Search Documents

By S. McGinn, G. Schnakenberg, D. Petrie, A. Bugarski, M. Grenier

As part of the Diesel Emissions Evaluation Program (DEEP) consortium, Noranda Inc. has undertaken a field project to evaluate the overall performance of the latest diesel particulate filter technology (DPF) at its Brunswick Mine in Bathurst, New Brunswick. Performance of the filtration systems is evaluated with respect to their ability to reduce tailpipe emissions and concentrations of diesel particulate matter (DPM) and noxious gases in mine air, efficiency of filter regeneration process, maintenance requirements, reliability, and acceptance. Four different particulate filter systems deployed on heavy production vehicles are subjected to an 18-month field evaluation. Over the evaluation period the vehicles will have accumulated approximately 4000 operating hours in production. This paper presents the results of testing conducted mid way through the 18-month field trials. The 400- meter section of the mine drift at 525-5 sub level, hereinafter referred to as the "isolated zone" was isolated between intake and exhaust fan systems and sealed with bulkheads against leakage. The isolated zone was ventilated at the rate required per CSA Standards and issued by CANMET for the engines tested. Four vehicles, two load-haul-dumps (LHDs) and two trucks, retrofitted with particulate filter systems were tested along with a new identical model LHD and truck equipped with exhaust systems consisting of a catalytic converter (DOC) and muffler. The test vehicles were operated individually inside the isolated zone for approximately 4 hours over simulated production duty cycles. Measurements of ambient concentrations of particulate matter, tailpipe emissions, and engine parameters were performed for each of the tested vehicles. The DPM samples for carbon were collected at the most up- stream end of the isolated zone, at the vehicle next to the operator, and at the most downstream or exhaust end of the isolated zone. The DPM samples were analyzed for total (organic and elemental) carbon using NIOSH Analytical Method 5040. Ambient concentrations of particulate matter at the exhaust end of the zone were also measured using Scanning Mobility Particle Sizer (SMPS), and real time PAH monitor (PAS 2000). Efficiency of the filters was also evaluated on a basis of tailpipe measurements performed using raw exhaust instruments the NanoMet and the UGAS. In addition, relevant engine parameters were obtained using Detroit Diesel Diagnostic Link (DDDL) and from exhaust backpressure and temperature measurements. Results from the tests proved conclusively that diesel particulate filters can significantly reduce the concentrations of air- borne DPM, but not without careful monitoring of both ambient and tailpipe emissions and not without careful attention with respect to maintaining the integrity of the DPF systems.

Objective: To evaluate the quantity of ventilation air reaching the face of a 40-ft box cut during a 40-ft, two-pass, extended cut and to examine ways to increase this quantity of air.

May 1, 1998

During 1999, there were six fatalities in surface mines involving haulage equipment colliding with a smaller vehicle or person, or backing over the edge of a dump point. All of these fatalities can be attributed to the extensive blind areas around large haulage equipment. Researchers at NIOSH are investigating various technologies that can be used to monitor these blind areas and provide information on nearby obstacles to an operator. So far, the technologies listed below have been tested on dump trucks used in surface mining. The selection of these systems was based on their ability to handle the tough environmental conditions found in mining operations and how well they detected obstacles out to 40 or 50 feet beyond the rear of large dump trucks. Some of the manufacturers of available collision warning and camera systems are also listed.

Jan 1, 2001

By C. K. Lee

This Bureau of Mines report presents results from experimental studies on wood fires in a laboratory-scale tunnel network. Experimental measurements include ignition delay time, flame spread rate, ventilation air and gas flow rates, wood temperature, gas temperature, pressure and composition, thermal flux, and smoke particulates. These measurements form a data base for fire-scaling studies and provide information on various fire processes, such as flow interaction between ventilation air and fire, fire throttling and reverse flow, and duct fire energetics. Results show how hazards of duct fires relate to the development of (1) asphyxiating and toxic fumes, (2) explosive gas mixtures, (3) throttling of ventilation air, and (4) high-temperature combustion products. Such fire hazards should be carefully considered when testing flammabilities of materials used in a confined underground mine environment.

Jan 1, 1980

By Jr. Smith

To investigate the effects of flow geometry on laminar flames, studies are in progress in this laboratory employing Bunsen-type burners with rectangular cross section. Interpretation of these studies requires a determination of the flow velocity at all points of the rectangular cross section for one dimensional steady laminar flow. In addition, values of the velocity gradient at the boundary for such flows are needed in the interpretation of blow-off and flash-back studies with burners of rectangular cross section. The hydrodynamical problem of steady laminar flow of a viscous fluid in channels of rectangular cross section was solved by Stokes. His results have been quoted by Love21 and by Dryden, Murnaghan, and Bateman,§/ and they have been discussed by Boussines and by Paschoud. It may be noted that the steady laminar flow of a viscous fluid in channels of rectangular cross section constitutes a hydrodynamical analogue for the problem of the torsion of an isotropic prism of rectangular cross section.

Jan 1, 1952

By Foster Fraas

The Bureau of Mines investigated a method for calculating values of adsorption energy; the goal was to devise an equation consistent with experimental data accumulated in the investigation of adsorption as related to ore separation processes. Numerical identification of the constants of a previously formulated equation provided an equation by which values of adsorption energy could be calculated. Values thus calculated checked with those obtained by calorimetric measurement.

Jan 1, 1965

By H. B. Humphrey, F. E. Cash

From 1900 to 1929 , 1,005 or approximately 30 per cent of all fatalities in the coal mines of Alabama were caused by fires or explosions of gas and dust . In the 3 -year period from 1927 to 1929 only 15 men were killed by these causes , a reduction from 30 to 9 per cent of the total . Notwithstanding this marked improvement , which is due largely to the efforts made by the State inspection department , the operators , and the Bureau of Mines to stamp out this type of disaster , Alabama still has more than its share of such fatalities which can and should be prevented. A list of explosions from 1894 to 1929 compiled from information obtained through the records of the State Inspector's office , the reports of Engineers of the Bureau of Mines , and the operators , is given in Table

Oct 1, 1930

By J. W. Eckerd, W. S. Sanner, P. L. Woolf, R. E. McKeever

The Bureau of Mines experimental blast furnace was operated successfully with anthracite metallurgical briquets . Tuyère pressures were higher and more erratic than for operations using coke , and furnace " hangs " occurred more frequently . Higher hot - blast temperatures were required to maintain the quality of the metal . By using higher hot blast temperatures , the fuel and production rates and slag volumes were comparable to those obtained for all - coke operation . The anthracite metallurgical briquets exhibited excellent mechanical strength and descended through the shaft of the furnace with little breakage or reduction in size .

Jan 1, 1964

By H. Foster Bain

Ten years ago there was no general , country-wide service for the systematic training of miners in matters relating to safety . A beginning only had been made at a few scattered points . Under the old conditions each man was left largely to look out for himself in meeting the hazards of his day's work, and the foreman , shift bosses , and superintendents chiefly relied upon improvision when major accidents occurred . So long as the mines were small and the workers highly intelligent and well trained in routine mining methods , and when too , the pressure for output had not yet speeded up industry to the extent it has since those days , there was something to be said for this lais- sez faire attitude . When , however , the rapid expansion of industry lead to the introduction of new and little trained labor and to units of production of greatly increased size , the natural dangers of mining were greatly intensified . An accident in a small mine affects only a few; the same accident in a large mine , unless proper precautions have been taken , may cost the lives of many . The public does not generally recognize that the greatly increased outputs of the mines , of coal mines in particular , have been in recent years , obtained from substantially the same number of miners as ten years ago but with a personnel not nearly so well trained in mining . It is inevitable under : such conditions that more care must be devoted to avoiding accidents and much more elaborate preparations made for meeting them . In the years immediately preceding the establishment of the Bureau of Mines this speeding up of industry , change in the character of mine labor , and increasing hazard had all begun to be felt . Immediately prior to the organization of the Bureau of Mines , public attention had been drawn to a series of disastrous coal-mine explosions , to the increasing frequency of these disasters , and to the terrible loss of human life . resulting therefrom. One of the first problems , therefore ; confronting the Bureau was clearly that of finding methods of reducing the number of such disasters and lessening the severity of those that continued to occur . Toward this object were immediately directed the energies not only of the Bureau of Mines but also those of State mine inspectors , mine operators and various other agencies , all of whom were urged to cooperate in this great humanitarian work. The results of this work naturally cannot be measured by figures only . Work for increasing the health , safety , comfort , and happiness of human beings may not be gaged with mathematical precision . But certain features of this work as revealed by the record from year to year are of much interest . ”

Apr 1, 1921

By G. G. Campbell

Bureau of Mines research to develop an in situ retorting recovery method for oil shale has involved field testing of fracturing techniques for creating fluid-flow paths in impermeable oil shale. Electrolinking, hydraulic fracturing without and with sand propping, and explosive fracturing with a liquid explosive were tested in a 25-ft-square, five-spot pattern. These wells were drilled into oil shale at 50-to 88-ft depths near Rock Springs, Wyo. Results of the fracturing tests were evaluated by injecting air into a test well and measuring flow rates and flow profiles in adjacent test wells before and after each test. To identify points of air entry (location of fractures) in wells, flow profiles were determined by use of inflatable packers and by continuous logging with an airflow probe developed during the fracturing program. Electrolinking and hydraulic fracturing without sand propping were relatively ineffective; hydraulic fracturing with sand propping created horizontal fractures with desirable flow capacity; and fracture flow capacity was significantly increased by detonation of nitro-glycerin displaced in the natural and hydraulically induced fracture systems.

Jan 1, 1970

By Jr. Joyce

This report describes sulfatization of nickeliferous laterites from Puerto Rico and the Philippines for recovery of water-soluble nickel and cobalt sulfates. Temperatures ranging from 665 C to 710 C and a 10-percent sulfur dioxide-air reaction gas were employed during batch-roasting tests and during continuous countercurrent treatment in a 2-inch-diameter shaft furnace. A maximum of 69 percent of the nickel and 76 percent of the cobalt were recovered from one sample of Puerto Rican laterite, and a maximum of 96 percent of the nickel and 91 percent of the cobalt were recovered from the Philippine laterite.

Jan 1, 1965

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By W. W. Adams

Reports received by the Bureau of Mines, Department of Commerce, from State mine inspectors, for November, 1930, showed that 219 men were killed in the coal mines of the United States during the month, an increase of 25 over the previous month and 33 over November, 1929. On the other hand the production of coal decreased, the output of 43,329,000 tons in November being 8,397,000 tons less than in October and 9,005,000 tons less than in November a year ago. The larger number of fatalities accompanied by a smaller output of coal resulted in a higher death rate4 per million tons in November than in the same month last year or in October, 1930. The November rate was 5.05, as compared with 3.55 for November, 1929 and 3.75 for October, 1930. The increase in the rate for the industry as a whole was chargeable entirely to bituminous mines,, as the anthracite mines had fewer fatalities in November than in either of the previous months to which reference has been made. Reports for bituminous mines alone 'allowed that accidents at class of mines resulted in a death rate of 5.12, based on 195 fatalities and a production of 38,122,000 tons. This rate indicated an increase of 55 per cent over the rate for October, of the same year, and 72 per cent over the rate for November, 1929. The October record was 146 fatalities and 44,150,000 tons, and that for November a year ago was 138 deaths and a production of 46,514,000 tons. Twenty-four deaths occurred at anthracite mines in November, 1970: the output of coal was 5,207,000 tons, hence the rate was 4.61 per million tons. During the corresponding month a year ago there were 48 deaths and 5,820,000 tons of coal produced, which indicated a death rate of 8.25. In October, 1930, the death rate was o.34; based on 48 deaths and 7,576,000 tons.

Jan 1, 1930

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964

By C. M. Mason

The current Bureau of Mines active list of permissible explosives includes 95 brands. Twelve are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1968

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general; the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By G. R. Hopkins, E. W. COCHRANE

According to reports received by the United States Bureau of Mines , Department of Commerce , as of January 1 , 1930 , there were 412 completed refineries in the United States with a daily crude oil capacity of 3,755,585 barrels . This compares with 413 refineries of 3,509,540 barrels capacity on January 1 , 1929 , which indicates that whereas the number of refineries was practically unchanged , the total capacity increased 8 per cent during the past year . Of the completed plants as of January 1 , 1930 , 358 plants , of 3,634,825 barrels total capacity , were operating and 54 , with a capacity of 130,760 barrels , were shut down . Compared with a year ago , this indicates a decline in the percentage of the total refinery capacity that is inoperative . There has been a decided decrease in the number of shut-down plants since 1924 and 1925 , when one plant in every three was inoperative . Many of the inoperative plants of 1924 and 1925 were constructed soon after the boom times of 1920. Some of these were operated for a time but were unable to show a profit during 1923 and 1924 , when an overproduction of crude petroleum was accompanied by demoralized markets for refined products . Prices for refined products improved in 1925 and 1926 , but only a comparatively few of the shut -down plants , then partly obsolete , were able to obtain or renew their crude connections and compete successfully with the larger , more firmly established refineries . After five years or more of continuous idleness , a refinery would be rendered practically useless through corrosion and obsolescence . Consequently , most plants now being carried as " shut -down " have operated intermittently since 1923 . struction . A material change occurred in 1929 in the matter of plants under con- On January 1 , 1929 , there were 14 plants under construction , with a potential capacity of 99,000 barrels per day , whereas on January 1 , 1930 , there were only eight plants of 37,200 barrels capacity being built . This decline was due to the fact that the construction program in west Texas , which was at or near its height on January 1 , 1929 , was completed prior to January 1 , 1930 .

Apr 1, 1930

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968

By Jeffrey H. Welsh

This report presents a study on the use of computerized, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1982