Search Documents

By W. A. Haley

This is the second of a series of publications that describes the progress of mechanical longwall coal mining in the United States in which a German coal planer was employed.3/ Details of the equipment, a description of its operation, and the results obtained in mining the experimental panel were published in the preceding report. Experimental mining with the planer in the first panel showed an improvement in performance over conventional mining methods at the coal company's Stotesbury 11 mine. The work, which was begun on an experimental basis, soon proved successful, and the coal company purchased the equipment for continued use. Two panels, adjacent to the first, were developed and mined with the planer. Each of these panels was shorter than the preceding one because water seepage from a surface creek limited development. On completion of mining in the third panel, the planer equipment was moved by the cooperating company to a nearby mine operated in the same coal bed where a large area of coal suitable for planer mining is available.

Jan 1, 1954

By J. H. Holden, G. R. Strimbeck, L. F. Willmott, W. R. Huff

A pilot - scale fluidized feeder was developed for continuously feeding up to 1 ton of pulverized coal per hour to a pressure gasifier . Fluidization in the 3 - foot - diameter by 34-1 / 2 - foot - high feeder is effected by two streams of inert gas , a technique called zone fluidization . A stream of inert gas through a drilled plate in the base of a central column near the bottom of the feeder fluidizes the coal . Another stream through a drilled plate in the annulus between the central column and feeder wall provides a source of semifluidized coal for the central column . Fluidized coal from the central column discharges through an extraction funnel and discharge line . Zone fluidization provided good fluidization with moderate requirement for fluidizing gas . Instruments were developed for metering and recording the flow rate of fluidized coal . A system was developed for storing , and weighing pulverized coal , and then delivering it in fluidized form at about 1 to 8 tons per hour .

Jan 1, 1964

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rub¬ber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber.A sample of gasoline was obtained from the tank in which Cunningham met his death. Examination by Dr. E. W. Dean of the Petroleum Division of the Bureau of Mines gave the following results.This shows the gasoline to be heavy and typical of the gasolines sold throughout Colorado for motor fuel A. Salvus half hour oxygen apparatus was arranged with the breathing bag only in a gas tight box in which the space was kept saturated with the vapor of this gasoline. The main part of the apparatus was outside the box. Oxygen from the apparatus was breathed by a man in the usual manner. Gas samples were taken from the box at intervals to determine the concentration of gasoline vapor, also samples of the oxygen breathed were taken from a side tube in the mouthpiece. The room temperature was 75°F. The concentration of gasoline vapor in the box at the beginning of the test was 4.3%. The man breathing from the apparatus thought he detected gasoline in his oxygen in two minutes after starting the test. Analysis of the inspired oxygen at this time showed 0.03% gasoline vapor. The same man remained on the apparatus for 18 1/2 minutes without suffering any ill effects. His place vas then taken by another man who wore the apparatus until the oxygen was exhausted without noticing more than a trace of gasoline at any time. At the end of the test the inspired oxygen contained 0.07% gasoline vapor. The total time of test was 38 minutes."

Dec 1, 1919

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By W. E. Wallace, P. S. Raghootama, M. S. Seehra, C. A. Hill, M. J. Keane, P. Mike

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte hemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz, kaolin, and alumina dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect cf lecithin adsorption. Dust hemolytic potential versus media pH are presented. Fourier transform infrared spectroscopy and photoacoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis.Introduction Quarts dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and' progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction. In the alveolar spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, sagas other functions, mechanically stabilises the lung from collapse by reducing the surface tension of water in the alveolar sacs.(1) This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11% in dog lavage fluid). and phospholipids (about 88%).(2) Fhosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalaitoyl lecithin (DPL).(2) Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occuring upon deposition of a particle in a pulmonary alveolus.(3)"

Jan 1, 1988

By W. G. Hopkins

The development of systems for location of miners who have become entrapped following a mine disaster has been one of the major research goals in the Bureau of Mines. This study details the preliminary development of such a system. Current technologies for locating trapped miners from the surface are either simple direction finders or time difference pulse systems that have accuracy limitations. Developing technologies using full vector field measurements at several receiving points are currently being studied. The necessity of measuring field strength with great accuracy can be a drawback in these systems. A system that operates with continuous wave radio signals, whose phase differences can be measured accurately even in weak signal conditions, greatly improves the location accuracy. A microcomputer would be used in conjunction with the system, to gather and manipulate the data to automatically pinpoint the location of the trapped miner. Comparison of this system with existing technology indicates a favorable accuracy/complexity ratio for the phase difference of arrival technique.

Jan 1, 2011

By A. J. Barry

An apparatus and procedure have been developed for testing the anchorage effectiveness of slotted-type bolts. The apparatus consists of: (1) A hydrualic Jack assembly for loading the bolt and (2) a device (extensometer or cathetometer) for measuring displacement of the bolt as it is loaded. This apparatus and procedure permit measurment of anchor slip for loads up to the yield load of the bolt. Two representative makes of slotted-type bolts (a total of 94 bolts) were tested in typical sandstone and shale mine roof. Analysis of the test results showed that (1) anchorage capacities up to the yield load of the bolts can be developed in either rock type; (2) the shape of the slotted end of the bolt affects the ease with which the bolt can be driven; (3) all bolts for which the driving distance was more than 1.25 inches produced satisfactory anchorage in both rock types (thus, driving distance can be used as a criterion for satisfactory anchorage); (4) for the group of bolts that was satisfactorily anchored the anchor slip was unaffected by the type of bolt but was considerably larger in shale than in sandstone; and (5) the bolt expansion, that is, the amount the wedge expands the prongs in excess of the diameter of the hole, can also be employed as a criterion for satisfactory anchorage. Although the bolt-expansion and driving-distance results do not differ appreciably, the latter is recommended because it is easier to determine.

Jan 1, 1954

By Oliver Bowles

"On January 15, 1920, a man was killed by falling rock in a limestone quarry in Utah. The quarry was visited by a representative of the Industrial Commission of Utah, and the cause of the accident was carefully determined. The facts concerning this accident, and the Bureau's recommendations are given in some detail in the hope that quarrymen may take steps to avoid dangerous conditions, and thus reduce the liability to accident.The quarry rock face is about 180 feet high, and the ledge is covered with an overburden of 10 to 20 feet of a mixture of soil and boulder. The rock face is not vertical, but slants at an angle of about 45° to 50°, while the stripping face stands at an angle of 70° to 80°, and is flush with the rock face. The conditions are shown in the accompanying figure.The man who was killed was employed in breaking rock at the foot of the quarry wall. The sun had been shining on the stripping face, and probably thawed the ground, thus permitting a boulder weighing about 20 pounds to roll down the slanting face, striking, and almost instantly killing the workman who was working with his back toward the quarry wall."

Feb 1, 1920

By Thomas J. Peters

During the 1982 Bureau of Mines study, 55 lode and 17 placer claims were held in the RARE II area. An estimated 150 lode claims and 50 placer claim, have been located in the study area; five were patented. There are no mineral leases. Gold has been produced from 8 lode mines and stream gravels have been worked for placer gold at 4 sites. Two suction dredges were active in stream gravels, but no significant gravel bars are identified. Identified mineral resources in the Weaver Bally area are gold and byproduct silver. The identified resources are at the Globe Mine, where approximately 33,000 tons of indicated marginal reserves (2,000 tons in the RARE II area, and 31,000 tons in the adjacent proposed Trinity Alps Wilderness) contain 0.45 oz gold per ton and probably 0.1 oz silver per ton. There are an additional 150,000 tons of inferred marginal reserves (35,000 tons in the RARE II area, and 115,000 tons in the adjacent proposed wilderness) averaging 0.38 oz gold per ton and probably 0.1 oz silver per ton. There is high potential for additional resources at the Globe Mine.

Jan 1, 1983

By J. E. Tiffany

Some of the gases produced by permissible explosives on detonation are poisonous, and the probable hazard involved by the inhalation of carbon monoxide in the past has been evaluated from results of tests in the Bichel Gage. Tests have now been made in the Experimental Coal Mine of the Bureau of Mines at Bruceton, Pa., to determine the composition of the gases obtained under actual mining conditions for the purpose of comparing these, results with those found by the Bichel gage tests. Two permissible explosives were procured for these tests, one that produces a relatively low quantity of poisonous gases in the Bichel gage (24.8 liters per 1-1/2 pounds of explosive) and another that produces a relatively high quantity of poisonous gases (94.6 liters per 1-1/2 pounds). The first of these is designated by the Bureau of Mines as a class A4/ explosive and the other is designated a class B explosive. In comparison with Bichel-gage tests, the shooting of permissible explosives in a coal shot hole resulted in a large reduction in the quantity of carbon monoxide, the principal poisonous gas, which; in the mine tests, was only 22 percent of that found in Bichel-gage tests: The quantity of carbon monoxide from the class B explosive in Bichel-gage tests was 3.8 times larger than that from the class A explosive; in the coalmine tests the ratio was 4:1. The concentrations of carbon monoxide in the mine tests, as determined by analysis of the atmosphere in an enclosed space resulting from shooting 1-1/2-pound and 3-pound charges of the class A explosive, were 0.03 and 0.06 percent, respectively, and the concentrations from 1-1/2-pound and 3-pound charges of the class B explosive were 0.10 and 0.24 percent.

Jan 1, 1950

By George N. Aul

This report describes a method developed by the Bureau of Mines for sealing horizontal degasification holes so that they do not create a gas explosion hazard when intercepted by mining. A cement slurry is pumped into the hole through an injection pipe that extends to the back of the hole. Pumping continues until the slurry returns through the annulus to the hole collar. The hole is then shut in and the grout allowed to harden. Application of the procedure to six horizontal degasification holes at Eastern Associated Coal Corp.'s Honey Run shaft is discussed.

Jan 1, 1979

Founded in 1994 through a joint effort between Underwriters Laboratories Inc. (UL), the U.S. Consumer Product Safety Commission (CPSC) and the National Electrical Manufacturers Association (NEMA), the Electrical Safety Foundation International (ESFI) is North America?s only non-profit organization dedicated exclusively to promoting electrical safety in the home, school and workplace. ESFI is a 501(c)(3) organization funded by electrical manufacturers and distributors, independent testing laboratories, utilities, safety and consumer groups, and trade and labor associations. ESFI sponsors National Electrical Safety Month each May, and engages in public education campaigns and proactive media relations to help reduce property damage, personal injury and death due to electrical accidents. The Foundation does not engage in code or standard writing or lobbying and does not solicit individuals.

Jan 1, 2004

By H. B. Humphrey, F. E. Cash

The following information on accidents in Alabama during 1930 was compiled from data obtained from the companies represented in a course on accident prevention given by the United States Bureau of Mines in Birmingham. These mines produced nearly three-quarters of the tonnage of that State for the year, and included most of the larger operations in the district. The figures are probably representative of the mines which are doing recognized safety work, and are better than the average for all the mines in Alabama. Table 1 lists the days lost in accordance with the weights given to fatalities and permanent disabilities, part and total, which is the scale used in the National Safety Com¬ petition for Mines, conducted by this bureau. By way of explanation, temporary disabilities are weighted according to actual number of calendar days of disability, including Sundays and holidays — that is, all days are counted except the day of accident and day of employee's ability to return to duty. Hernia is classed as a temporary disability to be charged with the actual number of calendar days during which the employee was unable to work. Table 2 gives the number of accidents and the days lost from each cause at 45 coal mines and 7 iron ore mines, also the average frequency and severity rates.

Aug 1, 1931

By Alan R. Buehler

A mineral survey of the 67, 110-acre Raven?s Eye WSA (Wilderness Study Area) in the north-central Snake River Plain of Idaho was conducted by the U.S. Bureau of Mines in 1985, at the request of the Bureau of Land Management. The WSA is in Blaine and Lincoln Counties; the northwest corner is about 1 mile east of Carey, 10. A search of county mining claim records indicated that no claims have been located in the WSA. Basaltic lava is the only rock type exposed within the WSA. A platy variety of lava (slab pahoehoe) occurs that is produced from other lava fields in southern Idaho. The material is marketed as decorative stone, used for wall veneers, and retails for approximately $125/ton. Within the W5A, approximately 18,000 tons of indicated reserves are concentrated in two areas, and a total of 12,000 tons of indicated subeconomic resources were found at six other localities. An additional 10,000 tons of inferred subeconomic resources are unevenly distributed over the remainder of the WSA.

Jan 1, 1986

By R. C. Butman

The Lincoln Terminal System (LTS) is a stand-alone computerized training device that presents high quality visual displays, and audio messages to a student. A keyboard is provided for student input. A variety of student-machine interactive programs arc provided. These programs allow the author/instructor to evaluate numerical entries and responses to simple and compound multiple-choice questions (where a compound choice is defined to be more than one choice, ordered or unordered from one or more list(s) of choices. Descriptions of LTS applications, lesson development procedures, hardware provided and support facilities required are given. A contract history summary, and a bibliography of reports published under three successive BoM contracts supporting LTS development, is provided.

Jan 1, 1979

By L. L. Oden

The Bureau of Mines is conducting research to develop methanation catalysts for converting synthesis gas derived from coal to synthetic natural gas. This report describes a method to prepare supported Raney nickel coatings by dipping screen-covered nickel sheet in molten aluminum-nickel alloy. Coatings were formed at 1,050° C that were comparable in thickness, composition, microstructure, and catalytic properties to flame-sprayed commercially pre-pared Raney nickel. A molten salt comprising cryolite-8 wt-pct LiF was employed over the molten metal bath to clean and preheat the substrates, to protect the metal bath from oxidation, and to heattreat the coated specimens. Immediately following heat treatment, specimens were quenched to 700° C in a molten salt bath containing CaC12-34.5 wt-pct NaCl, which also functioned to remove the insoluble occluded fluoride salt.

Jan 1, 1976

By W. H. Kerns

The Critchfield manganese deposit, Huntingdon County, Pa., was investigated by the Bureau of Mines in October 1942. Iron ore was mined from an open cut just southeast of the manganese deposit about 80 years ago. The Critchfield Sand & Feldspar Co. was operating (1942) a clay-mining and beneficiation plant northeast of the manganese deposit. The Bureau completed six rotary bucket-drill holes and three hand-auger holes, aggregating 370 feet on the deposit. This report describes the work performed and presents the results obtained.

Jan 1, 1948

By Knox Van Dyke, Vincent Castranova, Lixin Wu, Mark J. Reasor, James M. Antonini

"One of the proposed mechanisms involved in the pathogenesis of silicosis is that inhaled silica dust activates a ""respiratory burst"" in pulmonary phagocytes, such as macrophages and neutrophils. This increase in oxidative metabolism results in enhanced generation of reactive oxygen species which if produced in excess, would overwhelm natural defense mechanisms and cause damage to the lung parenchyma. This damage would then result in scarring, fibrosis, and decreased gas exchange.Weiss and LoBuglio' have listed several oxygen species produced by phagocytes which may be involved in cellular injury. These oxidants include superoxide anion, hydrogen, peroxide, hydroxyl radical, and hypochlorous acid. Superoxide anion (0;) is generated from molecular oxygen by the plasma membrane bound enzyme NADPH oxidase according to the following reaction:Once generated, superoxide anion can form hydrogen peroxide:In the presence of myeloperoxidase and halide, hydrogen peroxide can form hypochlorous acid:Superoxide and hydrogen peroxide can also form highly reactive hydroxyl radicals. Hydroxyl radicals can be generated slowly by the Haber-Weiss reaction:In addition. hydroxyl radical production can be catalyzed via the Fenton reaction:Hydroxyl radicals can also be generated from the reaction of superoxide and hypochlorous acid as follows:Recent investigations suggest that, in addition to the reactive oxygen species discussed above, nitric oxide may be a potential mediator of silica-induced toxicity.2-4 Nitric oxide (NO') can be generated by the cytosolic enzyme nitric oxide synthase according to the following reaction:NO synthase exists in two forms. i.e.. a constitutive. Ca2+-calmodulin-dependent form and an inducible. Ca2+-calmodulin-independent form. In pulmonary phagocytes. the activity of the constitutive form of NO synthase is low. However. NO synthase can be induced in macrophages and neutrophils by a variety of stimulants such as lipopolysaccharide. interferon y. chemotactic peptide, platelet activating factor, or leukotriene B4.3.5Once generated. nitric oxide can combine with superoxide anion to form peroxynitrite as follows:Peroxynitrite is a potent oxidizing agent. In addition, peroxynitrite can form peroxynitrous acid. which in turn can produce hydroxyl radical and nitrogen dioxide (all of which exhibit strong oxidizing potential) by the following reactions:Oxygen metabolites have been shown to cause lung damage in vivo.6 Such damage includes edema. leakiness of the alveolar endothelial/epithelial barriers, and airway constriction.7 Superoxide and hydrogen peroxide have been associated with membrane damage and cell lysis.8 These oxidants have also been associated with alteration of cytoskeletal structures at cell-cell junctions and elevation of transepithelial conductance in cultured monolayers.9 Macrophages or neutrophils can be stimulated by bacteria or phorbol myristate acetate to produce sufficient oxidant levels to lyse lymphoma cells.10 This cell killing is inhibited by catalase but is unaffected by superoxide dismutase. hydroxyl radical scavengers. or azide. i.e., an inhibitor of peroxidase. This implicates hydrogen peroxide as the active oxidant. Similarly. Weiss et al.11 have reported that hydrogen peroxide is critical in the death of cultured endothelial cells due to neutrophil activation. In addition. hydroxyl radicals generated by monocytes have been associated with cell injury.12 Lastly. peroxynitrite has been shown to oxidize sulfhydryl groups and to inactivate proteinase inhibitor making the lung more susceptible to damage caused by phagocytotic enzymes.' Therefore. a strong case can be made that activated pulmonary macrophages and neutrophils are capable of causing oxidant injury. This chapter presents in vitro and in vivo data indicating that silica is associated with the production of reactive oxygen species from these pulmonary phagocytes."

Jan 1, 1998

By Gary W. Krantz

Fibered, portland-cement-based gunite products were applied in the Bureau of Mines Lake Lynn Laboratory Experimental Mine using a variety of pneumatic guns and gunning crews, The demonstrated wet-mix (with silica fume), dry-mix, and surface bonding products were sampled by the Bureau and subjected to a suite of engineering analyses. Gunite flexural and compressive strength, rebound, permeability, porosity, dust loading, shooting rate, crew requirements, and cost factors were evaluated. Steel, fiberglass, or polypropylene fibers were contained in all but two of the gunires tested. Both Bureau and private testing laboratory analyses are provided for some products. Electron probe micro-analysis and X-ray diffraction analysis were performed on the silica fume fraction of the wet-mix gunite to characterize the dust. Aggregate size fraction distribution analyses were performed to provide strength relationships. Results indicate that all of the commercially available fibered-gunite materials tested can provide beneficial sealant, spall prevention, or roof stability control attributes for underground mining environments when applied by an experienced crew using a well-maintained gun, in accordance with product manufacturers' recommendations and when used for the designated purpose.

Jan 1, 1984