Search Documents

By Andrew J. Fergus

The purpose of this study was to provide basic information to aid further research on beryllium mineral flotation. Contact-angle and microflotation (Hallimond tube) methods were used to study collector action and flotation response of beryllium minerals and associated gangue minerals with representative commercial surfactants. Chrysoberyl received prime attention. Results indicated that selective flotation of beryl and chrysoberyl from fluorite and quartz is possible with sodium isooctyl phosphate below pH 2, and fluorite and topaz are readily collected by both anionic and cationic surfactants. Several modifying reagents were studied at one pH and one level of collector concentration. Aluminum sulfate, starch, and sodium silicate proved to be depressants in chrysoberyl flotation.

Jan 1, 1968

By J. L. Kohler

The final report for Phase II of Bureau of Hines Contract J0134025 concerns the research and development of sensitive ground-fault relays for dc utilization systems in mining. Sensitive relaying employs very low pickup levels such that, when used in conjunction with very high resistance grounding, the exposure of a human to ventricular fibrillation is significantly reduced. To delineate the desired relay characteristics, the report begins by reviewing previous research in this area. A theory for the saturable transformer used to sense the fault current is presented. The design of the ground fault relay is described in sufficient detail that it may be duplicated. Test procedures and results are given. Finally, conclusions and recommendations related to Phase II are presented.

Jan 1, 1986

By R. R. Schehl

The Bureau of Mines analyzed the structure of a high-grade metallurgical coke, carbonized at different temperatures in the range 500° to 1,000° C, through X-ray diffraction studies. Growth in the crystallite size with increasing coking temperature was calculated from profile analysis and compared with values obtained from the radial distribution function. The carbonization temperature appeared to have little influence upon the stack height, whereas the layer diameters more than doubled in size between 500° and 1,000° C. These results are comparable to those obtained from other studies of poorer quality cokes.

Jan 1, 1974

By B. W. Naugle

Twenty-nine sole-heated-oven expansion teats were made on 9 different coals, and apparent specific-Brevity tests were made on 12 of the resultant cokes. The coals, which ranged in dry, mineral-matter-free fixed-carbon content from 58.7 to 81.1 percent, were tested over a rather wide range of moisture content and dry-coal bulk density to determine the separate effects of these variables on linear coal expansion. The experimental data support the follow expression relating "as-tested" coal bulk density, moisture content, and linear expansion, [ER = (1-MR) (1+Et) - 1; BDt] where ER = fractional expansion at a reference bulk density of 55.0 lb. of 1 percent moisture coal per cu. ft., Et = fractional expansion at Mt and BDt, MR = reference moisture content = 0.01, Mt = moisture content, "as-tested", BDR = reference bulk density = 55.0 lb. per cu, ft., BDt = bulk density, "as-tested", 1b. per cu. ft.

Jan 1, 1957

Lower workers' dust exposures during bag stacking while ergonomically improving the bag stacking process. Approach Install a new pallet loading dust control system which uses a push-pull ventilation technique along with a hydraulic lift table to control the pallet loading height throughout the entire loading cycle. How It Works A low-volume, high-velocity blower system operating at approximately at 120 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-inch air jets (approximately 1,200-ft/min velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they en-train dust generated during bag stacking. The dust laden air is then captured by the exhaust ventilation system which draws approximately 2,500 cfm through an exhaust hood on the opposite side of the pallet.

Jan 1, 1989

By Paul M. Tyler

The alkali metals , sodium and potassium , and more particularly sodium , occur abundantly in chemical combination with other elements . The elements themselves are available in metallic form but are so active chemically that they oxidize rapidly in contact merely with the air . Potassium will even catch fire spontaneously in air , and both the metals will decompose water with explosive violence . Inasmuch as they are almost as soft as wax they are not suitable for the structural or other mechanical uses characteristic of ordinary metals , and consequently the uses of these elements even in the metallic condition are based upon chemical rather than physical qualities . Sodium metal is used largely as a commercial reducing agent , but potassium metal is rarely found outside of chemical laboratories . Numerous salts and other compounds of these elements enter largely into world trade and are commercially very important , but none of these compounds except sodium peroxide and sodium cyanide are made economically from the metals . Sodium is generally considered as rather an uncommon metal , but in point of annual tonnage produced it is far more important than mercury , magnesium , molybdenum , bismuth, cadmium, cobalt , gold , silver , or the various rarer metals .

Apr 1, 1932

By Glenn E. Johnson

The Bureau of Mines investigated the production of hydrogen cyanide by reacting powdered coal (minus 300 mesh) with ammonia at 1,250° C in a bench-scale study. Both metallic and ceramic reactors were used. Yields up to 0.7 cu ft of hydrogen cyanide per cubic foot of ammonia consumed r- obtained. The resulting ammonia conversion of about 75 volume-percent approximates conversion obtained commercially in processes utilizing natural gas and platinum catalysts. The coals that had higher volatile-matter contents gave the best yields of hydrogen cyanide. Allowing the coal to adsorb ammonia before reaction resulted in increased yields of hydrogen cyanide. Cost studies for a plant with a 40-million-pound-per-year capacity indi-cate that hydrogen cyanide can be profitably coproduced with carbon black, from coal and ammonia, at the current market price of hydrogen cyanide (11.5 cents/lb). These figures are based on heating the reactor electrically. If a cheaper heating method were devised the economics of the process would be more favorable.

Jan 1, 1967

By K. C. Dean

A flotation method was developed by the Bureau of Mines for concentrating pollucite, a cesium-aluminum-silicate mineral that may contain from 20 to 40 percent cesium oxide. Separation of the pollucite from three typical ores was achieved by froth flotation of the associated micas, feldspars, and other gangue minerals, using sulfuric and hydrofluoric acids and a cationic-type collector. A low-tenor, 8 percent cesium ore from Maine was upgraded to 20 percent cesium with recovery of 87 percent of the cesium. Relatively high- grade ores from Canada and Southern Rhodesia were beneficiated at lower ratios of concentration to 28 and 29 percent cesium content respectively with recovery of over 92 percent of the cesium. In addition to concentrating the cesium content of ores, the method also effectively separates cesium from sodium, potassium, and lithium, and in certain ores from rubidium. This is accomplished by selective froth flotation of the alkali metal-bearing gangue minerals such as lepidolite, other micas, and feldspars. Since the alkali metals, especially potassium and rubidium, are difficult to separate chemically or thermally from cesium to prepare high- purity cesium products, separation by physical mans is important.

Jan 1, 1962

By P. R. Tisot

The structural response of propped oil shale fractures was determined for each of two different grades of Green River oil shales (38.0 and 29.0 gpt) as they were heated in an inert atmosphere from ambient to subretorting temperatures (below those required for rapid pyrolysis of the organic matter). Small oil shale cores were propped apart by 3-mm glass beads to simulate a small cross section of a propped oil shale fracture between an injection and a producing well. These specimens were then heated at a uniform bate up to 800° F in a specially designed test cell under stress levels from 100 to 1,000 psi in biaxial and in triaxial confinement. Under the conditions of heat and compressive stress utilized in this study, all of the propped fractures in the two oil shales underwent structural deformation ranging from partial to complete collapse, as evidenced by proppant embedment. Structural collapse of induced fractures would in turn result in serious impairment or complete loss of the fracture flow capacities of the specimens. Results from this Bureau of Mines study indicate that underground retorting of Green River oil shale may be seriously impaired by loss of permeability when utilizing propped fractures in oil shales assaying more than 28 gpt.

Jan 1, 1975

By E. C. Perkins

This report describes a ferric chloride trap, based on formation of a low-melting sodium chloride-ferric chloride mixture of near-eutectic composition, and its use in chlorination of impure titaniferous materials. The trap is placed in the hot gas stream between the chlorination reactor and the condenser. Virtually all of the iron is removed by the trap. The condensed titanium tetrachloride is free of suspended solids and contains only a trace of iron. Four examples are given of the use of the ferric chloride trap in chlorination of impure titaniferous materials. INTRODUCTION In the Kroll process, ductile titanium metal is produced by reducing titanium tetrachloride with magnesium metal.4/ In commercial practice, titanium tetrachloride is produced by chlorinating titaniferous materials in the presence of carbon.2/ In 1957 most producers were using rutile, and virtually all plants were designed for its use. About four-fifths of the domestic consumption of rutile was imported from Australia. The Bureau of Mines, under provisions of contract DMP-116 with the General Services Administration, studied electrosmelting of domestic ilmenites and titaniferous magnetites to produce high-titanium slags with pig iron as a byproduct. Under the same contract, chlorination studies also were being made of these slags. Smelting was done at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., and chlorination at the Electrometallurgical Experiment Station, Boulder City, Nev.

Jan 1, 1958

By James H. Russell

Alkalized alumina (an active form of sodium aluminate) has been considered as a sorbent for the removal of sulfur dioxide from industrial flue gases. Four rate equations, each based on a different mechanism, were compared with the results of thin-bed sorption tests. It was found that each equation agreed with the experimental results, within experimental variance, over most of the range of sorption studied. First-order rate equations were generally satisfactory in explaining both sorption and regeneration. It is concluded that the equations developed are adequate for the design of commercial fluidized beds for the sorption of SO2 from industrial flue gases and regeneration of the alkalized alumina.

Jan 1, 1970

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By S. C. Rhoads

The Bureau of Mines is investigating low-chromium alloy substitutes for type 304 stainless steel (type 304 SS). The purpose of the research is to reduce the chromium content in austenitic stainless steels used for corrosion-resistant applications. Nine Fe-9Cr-12Ni alloys containing additions of 0 to 5 pct Mo, 0 to 2 pct V, and 0 to 2 pct Cu were selected for evaluation. All of the experimental alloys containing 5 pct Mo and an alloy containing 2Mo-2V-2Cu possessed structure and tensile strengths similar to those of type 304 SSe Alloys containing SMo-2V and SMo-2V-2Cu had ac-ceptable welding properties as measured by the Varestraint test. Alloys containing at least 2 pct Mo had cQrrosion resistance comparable to that of type 304 SS in solutions of nitric acid, phosphoric acid, acetic acid, and citric acid. In chlorides, all the experimental alloys were susceptible to localized corrosion and stress corrosion cracking similar to that of type 304 SSe The corrosion properties were established by weight-loss tests, electrochemical polarization tests, and stress-corrosion cracking tests. An Fe-9Cr-12Ni-SMo-2V alloy and an Fe-9Cr-12Ni-SMo-2V-2Cu alloy had a combination of welding properties, tensile properties, and corrosion resistances that were most comparable to those of 304 SS.

Jan 1, 1984

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964

By C. Harry Benedict

This paper presents the details of milling practice and costs at the conglomerate mill of the Calumet & Hecla Consolidated Copper Co., Lake Linden, Mich., and is one of a series on milling methods being published by the Bureau of Mines. GENERAL DESCRIPTION The mines of the Calumet & Hecla. Consolidated Copper Co. are located in the Keweenaw Peninsula of northern Michigan. The mines of this district lie in a belt not over 4 miles wide and 100 miles long, which contains more or lees commercial ore. The Calumet & Hecla properties are the farthest north, except for the Seneca, of the operating mines. The district borders on Lake Superior, and by means of the Portage and Torch Lake waterways the largest lane vessels, can transport coal and other supplies from the lower Lakes directly to the company docks.

Jan 1, 1930

By John R. Bradley

The available supply of fuel and power is a subject of importance at all times and particularly at this time. The following brief survey of fuel and power in the United States appraises the extent of the several primary sources of energy the approximate monthly demand, 1929-40; the chief centers of production and consumption; and shifts in the principal uses from 1929 to recent years. The period covers the boom year 1929, the years of the great depression, the more normal year 1937, the recession in 1938, the year 1939, and 1940 (which was affected by armament programs). In some instances, the data for 1939 and 1940 are preliminary. The four primary sources of fuel and power are coal, petroleum, natural gas, and water power. Wood fuel, important in some regions, and foreign trade in natural gas and hydroelectricity represent a relatively small part of the energy supply and are not considered in this study. The tonnages shown are in terms of coal, based upon the calorific or B. t. u. equivalents of the several sources of power. In practice, the usable heat or energy varies according to the type of equipment available for its use. For example, the efficiency of turbine water wheels and internal-combustion engines is much higher than that of steam plants and household-heating devices.

Jan 1, 1941

By McHenry Moiser

"SUMMARY This mine, which was discovered in 1846, was active in the 1850's, in the 1870's, and again in 1883. Since this last date, it has been idle. Two parallel bed-veins in lower Silurian limestone, about 50 feet apart, strike N. 70° E. and dip 70° NW. The north vein had an average width of 12 feet to a depth of 50 feet, where it was barren. The south vein had an average width of 16 feet to a depth of 75 feet; on the 110-foot level, although well-defined it carried little or no values. The zinc content of the ore was as high as 12 percent, and some lead and silver were associated with it. A reduction plant for production of spelter and zinc oxide was constructed at the mine. The only available record of production is for 1873 to 1876, inclusive, when 357 tons of smelter was shipped. The mine is caved and inaccessible, and nothing now remains of the treatment plant.Four holes totaling 1,046 feet wore diamond-drilled to probe for extensions of the ore in depth. Core recovery was about 85 percent. No samples were taken for analysis.INTRODUCTION AND ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The policy of the Bureau is to publish the facts devel¬oped by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The deposit was examined in 1944 by C. B. White, mining engineer of the Bureau of Minos. Diamond-drilling was under the immediate supervision of McHenry Mosier. 2/ The diamond-drill cores were logged by Arnold Brokaw, geologist, Federal Geological Survey, and 'wore filed in the core library of the Bureau of Mines, Mount Weather, Va."

Jun 1, 1948

By H. B. Humphrey, F. E. Cash

The Southern Appalachian coal field extends southward across Tennessee in a belt about 50 miles wide between the eastern and middle sections of the State. The earliest record of the production of coal in Tennessee is for 1840, and the first inspection laws were passed in 1881. In 1887, a second act of the legislature created the office of Chief Inspector, but little was done until 1891 when a new act was passed giving to the Department of Mines added duties and powers. Since that time, except for the years 1915 to 1918, com¬ prehensive annual reports have been published. Data for the tables given in this paper are taken from these annual reports, from those of the Southern Appalachian Coal Operators' Association, and from the publications of the United States Bureau of Mines, which has main¬ tained a station at Jellico, Tenn., since 1911. Complete figures for 1930 are not available yet and they are not included in the averages. The State Department of Mines, the operating companies, and the United States Bureau of Mines cooperate in accident-prevention work. It is the purpose of this report to present in uniform tables the available statistics in regard to fatal accidents in Tennessee and in the coal mines of the United States, in order that the progress in mine safety in Tennessee may be compared with that of the country as a whole, and the present period may be compared with various periods of the past, to indicate the main points of attack in the reduction of accidents.

Sep 1, 1931

Objective: To enable mine operators and mine inspectors to make quick and accurate measurements of the explosible nature of coal and rock dust mixtures.

Jul 1, 2008

By B. H. Eccleston, R. F. Kendall, D. E. Hirsch, Norman G. Foster

The mass spectra of 23 alkylthiophenes are presented , including 21 that have not been previously reported . Correlations between mass spectra and the structure of the thiophene homologs are discussed . Comparisons with , and corroboration of , earlier workers ' correlations and predictions are made . Several additional correlations are reported to enable the spectroscopist to identify the substituents on alkyl - substituted thiophenes , and the relationship of the mono - substituted and 2,5 - disubstituted alkylthiophenes is discussed in detail .

Jan 1, 1964