Search Documents

By Harry H. Ku

In December 1975, a report entitled "An Evaluation of the Accuracy of the Coal Mine Dust Sampling Program Administered by the Department of Interior" [1] was prepared by the Analytical Chemistry Division of the National Bureau of Standards (NBS), in response to a request by Senator Harrison A. Williams. Chairman, Committee on Labor and Public Welfare. The report attempted to evaluate the adequacy of (1) the personal sampler unit used to measure the coal dust concentration in the mines, (2) the procedures used by the Department of Interior (DOI) to analyze the dust samples obtained from mine operators, and (3) any recent studies made by the Department or private industry concerning the coal dust sampling equipment. Recommendations in the report of NBS included continued research efforts by the appropriate organization to correct the personal sampler deficiencies and to consider the use of area or stationary samplers as a supplement to the personal samplers. Concurrent with the NBS report cited above, the General Accounting Office (GAO) also issued a report in December, 1975 [2], suggesting that improvements are still needed in coal mine dust sampling programs and procedures relating to penalty assessments and collections. Among recommendations made by GAO, the following paragraph specifically called for actions by the agencies involved:

Jan 1, 1979

By B. J. Dalton

Several relationships between coexisting phases for analytical binary solutions near the critical point are given. These relationships were developed from a consideration of a (G u, P) surface at constant temperature and a (G u, T) surface at constant pressure, where G is the molal Gibbs free energy, u is the concentration of component 1 expressed as a mole fraction, G is the pressure, and T is the temperature. These formulas should facilitate the calculation of some of the quantities useful in making thermodynamic consistency checks on phase equilibria data about the critical point.

Jan 1, 1970

By F. E. Joyce

The Bureau of Mines studied copper-nickel minerals (mainly sulfides) of the Duluth Gabbro Complex in north-eastern Minnesota to determine their response to selective high-temperature sulfatization techniques. The gabbro, containing 0.44 percent copper and 0.13 percent nickel, was ground to minus 325 mesh and sulfatized in a heated, rotating, stainless steel bench-scale retort. Tests demonstrated that over 95 percent of the copper and 80 percent of the nickel can be converted to water-soluble sulfates, depending upon the roasting conditions employed. Yield equations were developed using regression analysis for predicting the extraction of copper and nickel between the temperature limits of 520° to 670° C, the roasting time limits of 3 to 7 hours, and S02 limits of 10 to 40 percent in S02-air mixtures.

Jan 1, 1971

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By John B. Umhau

[This !m-i~!.al survey giver, statistice.1 data res;?~dirf ~:rimay ard ?eco~- dqr or scmn tin used in thL: United St,ztas by industries an? incluclcz d;ta on stop&apos;ics, ~urchares, ard plnrt losr.c.5. It is :i ml:anwe of consq~tion in terms of fir.is1icd -prcd.~cts nz6.e iry initid ti11 Sabric:,.torc,, that is, aon- cerns that purchzse virc,in zni s~col~d&apos;l~y i.i.5 ti:; 01&apos; tin c;cra.. rav materi,als ar,d co:lrrert them into !ror?ucts such F!: ti:i plz.te, ~lloyr;, and. c?hemic?ls; comy~nias ;~urchn.&apos;.ii~; alloys, ch:rr.ic,~l::, or tin vl?.tc fcr furthcr a:mflzc- ture ?rc: ~-.f>t i~ci~~dcd. Tilit r~lqe:;tionrr::ire submit tod to consunern ar,nt:incd no dofinition of rnr.oncl.:ryr me$.-i; but, ovrirq to ti~i-: a~counti~ procedure used s.l~o~c-:t 1&apos; thu scrnn hac i~-.rtergol:e ch?rri?~ of ovinerzhip or titlo, thc rc!coverod t! n !its b~en i-c<;,r(it.!rj L.S r,e~3r;d:q met.1. Tbv tin content ~f ]

Jan 1, 1938

By Charles S. Allbright, Frank G. Schwartz, Marvin L. Whisman

Radioactive tracer techniques were used to gain a better knowledge of the types of compounds that cause gum formation in gasoline during storage . A selected organic compound was labeled with tritium and purified . An unstable gasoline was tagged by adding a small amount of the labeled compound . After storage of the gasoline at 110 ° F for 16 weeks , the gum that had formed was recovered . The amount of the test compound converted to gum was determined by liquid scintillation counting . About 70 compounds , including several classes and types , were studied . The compounds , listed in order of descending reactivity in the test fuel , were sulfur compounds , nitrogen compounds , polycyclic hydrocarbons , olefins , alkylbenzenes , and saturates . In the order of decreasing percentage of each in the gum , the compounds were monoolefins , alkylbenzenes , sulfur compounds , polycyclic hydrocarbons , nitrogen compounds , and diolefins . This type of information should be helpful in developing a method for predicting the storage stability of gasoline .

Jan 1, 1964

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks&apos; storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By F. G. Horino

The Bureau of Mines conducted compressive strength tests on model pillars of selected rock types with each pillar containing a critically oriented plane of weakness. The objective of these tests was to determine if a significant increase in the strength of the model pillar could be obtained by either (1) installing tensioned rock bolts through the pillar and normal to the plane of weakness, or (2) wrapping tensioned steel wire ropes around the pillar at uniformly spaced intervals along the pillar. Equations based on Coulomb&apos;s failure criterion are developed to predict uniaxial compressive strength of model pillars that are either rock-bolted or wire-roped. Laboratory compressive strength tests on unbolted and bolted model pillars of sandstone, marble, Indiana limestone, and oil shale containing a plane of weakness oriented at 45° showed that the bolted pillars are stronger than the unbolted pillars by 84, 31, 52, and 28 pct, respectively. Laboratory compres-sive strength tests on nonroped and roped model pillars of Texas limestone, sandstone, and granite containing planes of weakness showed that the roped pillars were stronger than the nonroped pillars by factors ranging from 1.01 to 2.41, depending upon the angle of the plane of weakness and the rock type. Rocks with a low Young&apos;s modulus benefited most by the wire-roping technique.

Jan 1, 1971

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By J. B. Gayle

A 1/2-ton experimental coke oven was installed ac the Bureau of Mines Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial slot-type ovens. Because of the small force exerted on the oven walls in most tests conducted to date (probably owing to the practice of charging coals and blends at a moisture content approximating that normal to commercial plants operating in this district), little information has been obtained about expansion properties. Two sole-heated ovens have therefore been constructed and used as supplementary equipment for determining the expansion properties of coals tested in the Tuscaloosa oven. The reasons for constructing the Tuscaloosa oven, the details of design, the operating, characteristics of the oven and the reproducibility of results have been discussed in previous publications. 3 4 5/ The present report deals with the effects of substituting various high- and low-volatile coals for components of a selected base blend carbonized under conditions similar to those normally used for producing foundry coke. Results of tests of 11 coals and 14 blends indicate that several blends tested rave cokes having physical properties very similar to those produced from the reference blend.

Jan 1, 1957

By Clarence O. Babcock

In this report, the Bureau of Mines presents a method for reducing the complexity of designing room-and-pillar mining systems by treating them as anisotropic soft inclusions in the surrounding ore or host rock. Theoretical models were derived for the calculation of the effective Young&apos;s moduli for these systems. The predicted behavior of the plate-type elements used in these models agreed well with test results from 21 plates each with 49 holes spaced on a 7 X 7 Cartesian grid. The plates behaved as anisotropic solids, the effective Young&apos;s moduli of which could be predicted from the scaled hole size and spacing. Actual hole shape was insignificant. The effective Young&apos;s moduli for simple mining systems are calculated in sample problems. This approach should provide information about field stress in the mining region and the stress distribution in the surrounding ore or host rock when the actual mining configuration is replaced by an anisotropic inclusion in a finite element analysis. The field stress within the inclusion can then be applied to the actual opening shape to determine the stress distribution within the mining region.

Jan 1, 1970

By J. A. Ruppert

The Bureau of Mines investigated methods of refining iron-contaminated zinc to marketable quality and developed a laboratory-scale process in which aluminum, added as a refining agent, reacted with the iron, forming solid Fe2Al which floated to the surface of the melt. Solids were separated by both filtration and centrifugation, using a unique type of "dipping" centrifuge devised during the work. Typical zinc recovery was 95 percent, and iron content of the metal was lowered from 0.37 to 0.02 percent.

Jan 1, 1967

By W. H. Young

PRODUCTION of bituminous coal and lignite increased substantially in 1963 compared with 1962 figures. The major items of production, consumption, exports, and productivity increased. However, certain key items declined. For the fourth year there was no upward trend in mechanization; the percentage of total tonnage mechanically loaded remained the same as in the 3 previous years and the percentage of total tonnage mechanically cleaned was smaller than in the previous year. Furthermore, the percentage of total production mined by stripping and by augers increased. Most significant was the continued decline in average value and employment. Production.-The output of bituminous coal and lignite in the United States in 1963--459 million tons-was 9 percent greater than the 422 million tons produced in 1962. Production was greater in 1963, largely because of expanded consumption by the electric utilities and an increase in exports.

Jan 1, 1964

By Charles Vaught, Henry J. Kellner, Michael J. Brnich, Henry P. Cole, William J. Wiehagen

In 1985, U.S. Bureau of Mines and University of Kentucky researchers began a series of studies relating to self-contained self-rescuer (SCSR) donning proficiency. During the next 5 years investigators examined a number of factors that have a bearing upon miners&apos; ability to put on and use the apparatus in an emergency: the procedure being taught; availability and utilization of training models; opportunities to practice; hygiene; and on-the-job training. This report presents an overview of that research. It is concluded that companies should adopt a hands-on training protocol that allows them to integrate SCSR donning practice into other workplace routines such as fire drills.

Jan 1, 1993

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By John P. Hager

This study investigated the formation of vapor complexes between aluminum chloride and the chlorides of iron, titanium, and silicon. For the A1-Fe-C1 system the proposed gaseous complex species is Al2Fe2C112(g), which is formed according to the reaction 2A1C13(s) + 2FeCl3(s) = Al2Fe2C112(g) The corresponding free energy expression was determined to be ?G° = 38091.49 - 71.45 ? T 400 < T < 600°K The vapor composition above AlC13 melts contaminated with FeC13 was calculated. In the Al-Ti-CI and Al-Si-Cl systems the proposed vapor complex species are Al2Ti2Cl14(g) and Al2Si2Cl14(g) respectively. Free energy expressions were estimated for the formation of the two complex species. Again, the vapor composition above AlCl3 melts contaiminated with TiCl4 or SiCl4 was determined. The results of this study were compared with previous studies on the three systems.

Jan 1, 1980

By J. W. Stevenson

The Bureau of Mines investigated the influence that atmospheric pressure changes exert in a gassy coal mil on a ventilating air current with a system of bleeder entries. During the season when abnormal barometric fluctuations usually occur, recording instruments monitored the air current ventilating an active coal-producing area. It HL he rate of coal production caused a more significant change in methane concentration than did barometric change. The hazard that accompanies methane release due to expansion of the gob gases during atmospheric lows was minimized by the effective bleeder system.

Jan 1, 1966

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By Phillip N. Yasnowsky

This Bureau of Mines report summarizes State severance taxes imposed on minerals and mineral fuels, provides a hypothetical example of how a State severance tax affects selected components of a firm&apos;s income statement, and uses the Bureau&apos;s Minerals Availability System (MAS) to estimate the effect of assumed changes in State severance tax rates on copper recovery cost at given levels of potential copper availability. A reduction of the rates to zero or a doubling of them results in changes in costs that are of the same order of magnitude as the cost of transporting copper to the United States from major foreign producing countries.

Jan 1, 1982