Search Documents

By H. D. Jacobs

A process for recovering both iron and manganese from four manganiferous ores of the Cuyuna Range was evaluated. It comprised: (1) Low-temperature gaseous reduction to convert nonmagnetic iron minerals to magnetite and manganic minerals to manganous oxide, (2) acid leaching to extract manganese, and (3) magnetic separation to reclaim iron from the leach residue. Iron recoveries from the magnetic products ranged from 70 percent to 90 percent; manganese recoveries from leach filtrates ranged from 75 percent to 95 percent. Two ores, from the Hillcrest and South Alstead properties, yielded magnetic products considered adequate for use as blast furnace feed. Although good yields of manganese were attained on all ores, appreciable iron accompanied the manganese into solution. Previous work, however, has shown that this iron can be precipitated almost quantitatively under autoclave oxygen pressure with very little loss of manganese.

Jan 1, 1970

By Roy T. Sorensen

The Bureau of Mines has investigated the recovery of cell-grade alu-mina by RCI leaching of calcined kaolin in the alumina miniplant at its Boulder City (NV) Engineering Laboratory. Classification and thickening were used for separating aluminum chloride leach liquor from the siliceous residue generated in the acid leaching step of the clay-HCI process. Coarse solids were classified from fines at 115 mesh and countercurrently washed in three additional spiral classifiers. Fines were treated in a conventional five-thickener, countercurrent decantation circuit. When this method was applied to the solids-liquid separation of slurry from RCI leaching of minus lO-mesh calcined kaolin, 75 pct of the residue reported as classifier sands and 25 pct as thickener underflow. Predicted individual classifier and thickener area requirements were 6 and 25 ft2/tpd, respectively. Total thickener circuit flocculant requirement was 2.4 lb/ton solids. Aluminum chloride pregnant liquor was produced that analyzed 8.4 pct A1203 and contained more than 97 pct of the alumina in the liquid phase of the slurry. Bench-scale settling tests were used to correlate fines content of leach residue to thickener area and flocculant requirements.

Jan 1, 1983

By C. J. Chindgren

A refractory-lined, garage-type automobile incinerator with a natural gas afterburner for air pollution control was cooperatively constructed and tested by the Bureau of Mines and the Wasatch Metal & Salvage Co. in Salt Lake City, Utah. The incinerator is capable of relatively smokeless burning of 32 to 60 cars per day, dependent on the degree to which the cars are stripped prior to incineration. Preliminary burning campaigns indicate the cost of incineration to be approximately $2.75 per car.

Jan 1, 1970

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

By D. E. Sullivan

The Minerals Availability Program of the Bureau of Mines conducts cost evaluations of current and potential mineral operations in the United States and foreign countries. The International Mining Cost Indexation System (IMCI) allows data of different time periods within a country to be updated to a common base year for analytical purposes. The IMCI comprises 12 factor cost indexes and an exchange rate series for 96 market economy countries, denominated in both local and U.S. currency. The IMCI for each country contains 12 time series indexes that measure the average annual rate of change in the cost of factor inputs to the mining industry within that country. Mining industry factor cost indexes include wages, plant and equipment, construction and mining materials, power and transportation, and other measures considered to comprise the majority of capital and operating costs. Cost data or proxies are collected in local currency. Index series within each country are constructed separately and indexed on a 1975 base year. The local currency index is converted to a U.S.-dollar-based currency index using an exchange ratio.

Jan 1, 1987

By F. E. Walker, S. J. Aresco, J. B. Janus

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal , expressed in British thermal units , and the composition as shown by proximate analyses . To these , when required , are added the ash- softening temperature , the free - swelling index , and the Hardgrove grindability index . Under most of these specification contracts the bidders guarantee the quality of the coal , and that guaranteed by the successful bidder becomes the standard of his contract . The deliveries are sampled in accordance with instructions 4/ issued by the Bureau of Mines ; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and , if it is not , a price adjustment is made . Analyses of the delivered coal and tipple samples ( samples collected at mine tipples as coal is being loaded into railroad cars or trucks ) provide valuable data for use in evaluating future bids . In addition , the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal . The Government purchased approximately 5 million tons of coal in fiscal year 1962. In connection with these purchases , the Bureau analyzed 7,114 samples . These are published ( table 1 ) for the use of Government officials and the public . A series of publications has been completed on coal analyses by States or , where production is small in any one State , by groups of adjacent States . In addition to analytical data showing composition and quality of coals of the States , the publications contain brief descriptions

Jan 1, 1963

By L. C. IlsLey

In January, 1922, a conference relative to trailing cables for use with permissible mining machines was held at the Pittsburgh Experiment Station of the U. S. Bureau of Mines. At this conference it was recommended that the bureau take steps to investigate the rubber-sheathed type of cables and to bring about the establishment of a list of approved cables. Effective until such time as a complete investigation could be made, the bureau asked the several manufacturers holding approvals for mining machines to recommend cables for use with their machines. In general the cables recommended were tentatively approved. Due to the lack of available personnel, no actual tests of cables were made until mid-1927. Meanwhile a field investigation of trailing cables was made at 20 mines of three coal companies in western Pennsylvania, and samples of cables were obtained from the manufacturers for laboratory tests. Twenty-five samples of the concentric-type cable, representing the product of five manufacturers, were obtained for the tests. These cables were of four sizes, as follows: 3 cables of No. 2 B & S gage, 17 cables of No. 3 B & S gage, 3 cables of No. 4 B & S gage, and 2 cables of No. 6 B & S gage.

Jan 1, 1929

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

By Benjamin C. Pollard

The location and production potential of a large block of strippable reserves in North Dakota were determined by using published data as a base and adding new drill hole data or other data contributed by companies that presently own or lease coal lands. Only beds exceeding 5 feet in thickness, under less than 120 feet of overburden, and in large blocks of 5 million tons or more were included in the estimates. All such reserves are in the Fort Union Formation of western North Dakota and are lignite in rank. Sixteen large blocks of reserves evaluated in this study are estimated to contain a total of 4.1 billion tons of strippable lignite.

Jan 1, 1972

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By A. W. Fahrenwald

The purpose of screening is to separate a crushed or natural product into one or more products in which size of grain is constant, or within certain size limits. The ore dresser finds need for this operation in the laboratory, in the study of ore-dressing processes, and for various purposes in the plants. In the plant, for example, screens are employed in closed circuit with crushing devices such as rolls, and sometimes are used in closed circuit with ball mills. Screens are generally used to prepare jig feed where a sized feed is wanted. For any given sieve opening there is in any feed a certain percentage of grains that will pass through the sieve meshes only with difficulty and under favorable conditions. For example, cylindrical grains of length greater than the maximum dimension of the sieve mesh and of diameter less than the sieve opening pass the sieve only when the long axis of the grain is normal or nearly normal to the sieve. Whether such grains should actually be in the through's or the oversize of a screening operation--considered from the point of view of the subsequent treatment of the grains--can not be said. The grains that pass the sieve opening in a screening process only under-favorable conditions have been named "difficult" grains by R. K. Warner.4 In many ore-dressing flow-sheets it probably matters little whether these difficult grains show up in the screen through's or oversize. The main objection to them is that they are sieve-blinding.

Jan 1, 1929

By Forrest T. Moyer

In 1969, the number of fatal injuries in the coal mining industry was lower than in any previous year and the number of nonfatal injuries was lower than in any preceding year except 1968. Fatal injuries in 1969 totaled 203 with frequency rates of 0.85 per million man-hours of worktime and 0.36 per million tons of coal These rates were new annual lows. Nonfatal injuries totaled 9,917 with frequency rates of 41.76 per million man-hours and 17.42 per million tons. The severity rate for fatal and nonfatal injuries combined was 7,359 days lost or charged per million man-hours. The average severity was 173 days lost or charged per injury. These statistics represent the injury experience of an average of 133,302 employees per day working an average of 225 days in 5,955 coal mines for a total of 237-5 million man-hours worked and a coal output of 565 2 million tons

Jan 1, 1973

By Robert C. Steckley

The Bureau of Mines performed a fragmentation experiment in cooperation with Duval Corporation in a porphyry copper-molybdenum deposit near the Sierrita pit south of Tucson, Ariz. This experiment evaluated the fragmentation created in a 10-hole test blast having blasthole spacings of 25, 20, and 15 feet. The 10 blastholes were 9 inches in diameter and contained a total of 17,400 pounds of aluminized slurry blasting agent in 50-foot columns with 60 feet of stemming. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. These core examinations included study of length recovery, rock quality designation (RQD), weight recovery, and size distribution. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the broken material on the surface. Fragmentation to depths of 110 feet was excellent from the 15-to 20-foot blasthole spacing patterns. Good breakage was also produced by the 25-foot pattern although the effects of the blast were not so obvious. In situ leaching tests were not conducted. However, based only on size consideration, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1975

By A. R. T. Dennues

"INTRODUCTION There are presented in this report the results of limited studies by the Bureau of Mines of the firedamp safety of some powder-powered tools proposed for use underground in coal mines. This study was made to obtain general information and specific technical data for a cable splicer and some rail punches now commercially available, the aim being to keep abreast of developments and to anticipate hazards.ACKNOWLEDGMENTSAcknowledgments are made to the Mine Safety Appliances Co., Pittsburgh, Pa., for supplying equipment for these tests, and to the Pittsburgh Coal Co. for making possible observations of the use of these tools in coal mines.The assistance of other members of the Explosives Division is acknowledged: J. E. Crawshaw, for examination of ammunition and, propellant powders; H. L. Wilson, for analyses of the natural gas used in the gallery and Jerome C. P. Weinheimer and Martin Bashel, for conducting the gallery tests.GENERALDescriptions of the DevicesPowder-powered tools of the type tested utilize the energy of charge of,propellant powder accomplish tasks. They are essentially small guns adapted to special work. Of the family of such tools now commercially available from one manufacturer, two have been proposed for use underground in coal mines, namely a cable splicer known as model TI and two models of rail punch known as R40 and R60. These tools employ blank-cartridge ammunition and special projectiles to accomplish the work indicated by these descriptive names."

Jul 1, 1947

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

In 2007, a total of 4,639 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 31.2% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,051; 44.2%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=373; 8.0%), followed by Texas (n=352; 7.6%).

Aug 1, 2009

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959