Search Documents

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

By Robert H. Bedford

The New Almaden mine was discovered in 1824, and since that date production of quicksilver has exceeded 1,000,000 flasks. Because of this high production record, the New Almaden area was, upon passage. by Congress of the Strategic Minerals Act of 1939, immediately considered by the Bureau of Mines as a promising location for exploration. In 1941, the Federal Geological Survey undertook a survey of the entire district. R. R. Trengove, an engineer of the Bureau of Mines, made a preliminary study for a project in 1942, and in August 1943 the Bureau, in close cooperation with the U. S. Geological Survey, began the development project described herein. The Bureau of Mines drilled 36 holes, totaling 6,807 feet of diamond drilling, along the contact between the serpentine and Franciscan, sandstones and other sedimentary formations. The ore bodies are found along this contact and occur in the carbonate-silica rock. This report briefly describes the location, history, and ore deposits of the property. The recent operations are outlined, and the work performed by the Bureau is explained in detail.

Jan 1, 1950

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the hydrogen cyanide (HCN) concentrations and smoke particle characteristics during the combustion of flexible polyurethane foams and other nitrogen-containing materials, for the development of a test parameter. The experiments were conducted in an approximately 2O-L furnace at set furnace temperatures of 250° and 1,000° C for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied as a function of time were the gaseous and aerosol HCN concentrations, the smoke particles average diameter (dg) and particle concentration (no), and the product of the smoke particle diameter and concentration (dgno). Carbon monoxide, carbon dioxide, and oxygen concentrations, sample mass weight loss, and furnace temperatures were also studied; analyses of nitrogen and cyanate content of the material were carried out. Results show that dgno correlates directly with the HCN concentrations, which depend on the nitrogen and cyanate contents of the material.

Jan 1, 2010

By Irving Hartmann

As part of the continuing effort by the Bureau of Mines to promote mine safety, research work is being conducted at the Experimental coal mine, Bruceton, Pa., on the prevention of coal-mine explosions and on other mine-safety problems. The principal subjects studied during the past 2 years are briefly described in this paper. Although at present these problems are relevant particularly to the mine layout and to high-speed mining practices in numerous American coal mines, it is hoped that the findings will prove interesting and useful also to our European research colleagues. Some of the investigations treated here will be presented in greater detail in forthcoming Bureau of Mines reports. 1. UNDERGROUND STORAGE OF COAL CUTTINGS The seams in mist American bituminous-coal mines are undercut, shear-cut, or top-cut before blasting. The cuttings arc generally loaded out with the balance of the coal. However, in some mines it is not economical to load and remove cuttings from the mine. This applies especially if the cut section of the seam is of appreciably lower grade than the rest of the coal, or if the cut is made partly into an adjacent stratum that is high in incombustible content. In such mines the cuttings are sometimes stored in random heaps in rooms or other areas, along the ribs of mine entries, or in layers on the floor of rooms or entries.

Jan 1, 1956

By G. S. Rice

The Experimental Mine of the United States Bureau of Mines is a unique coal mine that serves as a large-scale testing laboratory. It is used primarily for testing the explosibility of coal-dust and gases but is also the workshop for many other kinds of research work of which the chief object is to increase safety in mining. The mine is situated in Allegheny County, Pa., about 13 miles southwest of Pittsburgh among the high hills of the west bank of the Monongahela River, at the northeastern edge of the gas-coal district of the Pittsburgh coal bed which extends south through the Connellsville coking-coal district into West Virginia. The Pittsburgh bed, of the Upper Carboniferous age, is one of the most extensive continuous coal beds in the United States, if not in the world. Throughout large areas it shows remarkable uniformity of thickness, levelness, and character of coal, which is a coking coal of high-grade bituminous rank. Its thickness in the northern part is 5 to 5 ½ feet and in the central and southern part is 7 to 9 feet.

Jan 1, 1933

By Engelmann. William H.

In pursuit of innovative methods to improve mining productivity, the Bureau of Mines is investigating the use of inorganic salts as drilling fluid additives for penetration enhancement. Laboratory diamond drilling tests were performed on Westerly Granite with aluminum chloride solutions and on Sioux Quartzite with aluminum nitrate and aluminum, calcium, sodium, and zirconium chloride solutions as drilling fluid additives. These drilling results were compared with the average drilling performance using distilled, deionized water on Sioux Quartzite (12 replicate tests) and Westerly Granite (3 replicate tests). Maximum in-creases in penetration per given time and bit life were obtained when drilling with zero point of charge (ZPC) concentration solutions of each additive. For Sioux Quartzite, maximum increases in penetration and bit life ranged from 96 to 115 pct and 64 to 99 pct, respectively. For Westerly Granite, maximum increases in penetration of 155 and 165 pct and bit life of 109 and 136 pct were obtained at or near ZPC aluminum chloride concentrations of quartz (7.3 x 10-7 mol/L AIC13) and alkali feldspars (1.1 to 1.5 x 10-6 mol/L AIC13), respectively. This simultaneous increase in penetration per time together with extended bit life should result in increased productivity and reduced bit costs.

Jan 1, 1987

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

By Joseph M. Singer

Having established that sodium chloride reduces the incendivity of explosives, the Bureau of Mines studied the effect of sodium nitrate in reducing ignition hazards. Gallery experiments showed that sodium nitrate reduced the incendivity of certain explosives to 8 percent natural gas in air but increased their incendivity to coal dust predispersed in air. Laboratory experiments using hot jets from explosions of stoichiometric mixtures of methane-oxygen-nitrogen showed that both sodium chloride and sodium nitrate reduced the incendivity to methane, to mixtures of coal dust and methane) and to coal dust. The difference between the gallery and laboratory results with respect to coal dust is attributed to temperature-time effects.

Jan 1, 1967

By Frank A. Peters

This Bureau of Mines report is the second of a series of process evaluations planned to determine the relative processing costs of producing metallurgical-grade alumina from low-grade aluminous materials. Included in these evaluations are recommendations for additional research and development to improve the processes and to lower their costs. The design for each process is based on published work. The processes considered in this report are designed to extract alumina as aluminum chloride from calcined clay with 20 percent hydrochloric acid and to remove the silica residue by filtration. Iron is removed by one of the following processes: Isopropyl ether extraction, in which iron chloride is extracted before decomposing the aluminum chloride; gas precipitation, in which the aluminum chloride is precipitated with hydrogen chloride while leaving the iron chloride in solution; gas precipitation-isopropyl ether extraction, in which the aluminum chloride from precipitation is extracted with isopropyl ether, if necessary; caustic purification, in which a crude alumina is produced and then purified by a modified Bayer operation; or sinter purification, in which a crude alumina is produced and then purified by a lime-soda sinter operation. For plants producing 1,000 tons of alumina a day the estimated operating costs per ton of alumina are: [Isopropyl ether extraction process $ 65.09 Gas precipitation process 89.04 Gas precipitation-isopropyl ether extraction process 119.65 Caustic purification process 73.79 Sinter purification process 80.47] The estimated fixed capital costs per annual ton for these plants on a Marshall and Stevens chemical equipment basis of 240.0 are: [Isopropyl ether extraction process $229.03 Gas precipitation process 287.16 Gas precipitation-isopropyl ether extraction process 356.59 Caustic purification process 266.48 Sinter purification process 279.13]

Jan 1, 1962

By V. E. Edlund

As part of its efforts to devise new and improved methods for recovering lithium from unconventional resources , the Bureau of Mines investigated a lime -gypsum- roast , water- leach technique for processing lithiumenriched ( 0.01-0.68 pct Li ) clays . This report presents the results of a study of the technical feasibility of extracting lithium from raw material representative of clay beds associated with the McDermitt Caldera complex in Nevada and Oregon . prepared from water used Pellets suitable for bench-scale roasting studies were mixtures of minus 200 -mesh clay , limestone , and gypsum , with as the pelletizing agent . Roasting pelletized charges at 900 ° to 1,000° C temperatures for 1- to 4-h periods produced calcines that leached readily , yielding water - soluble lithium sulfate ( Li₂SO4 ) . A 5-3-3 ( weight ratio ) mix of clay , limestone , and gypsum produced calcines with the best leaching characteristics . More than 91 pct of the contained lithium was extracted from pelletized mix batches roasted in covered refractory boats . Lithium recovery decreased to about 87 pct when the mix was roasted under dynamic conditions in a gas - fired rotary furnace . A reaction mechanism was postulated which indicated that dilution and loss of SO2 and oxygen in the combustion exhaust adversely affected the leachability of the dynamically roasted calcine .

Jan 1, 1983

By R. S. Fowkes

Jetstream pressure distributions and coal cutting rates were determined for a number of nozzles and under different operating conditions. The jetstrearn pressure distribution data were fitted to an assumed curvilinear equation by the utilization of a numerical least-squares technique with the aid of a digital computer. Subsequent manipulation of the approximation equation showed that the total force of the jetstream, rather than its maximum pressure or total kinetic energy per unit Lime, was the most significant quantity affecting the coal cutting rate. A shorter method for assessing the ability of a nozzle to cut coal was found.

Jan 1, 1968

By Joseph D. Davis

The term "fusain" was first adopted from the French by the American geologist J. J. Stevenson in 1911, according to Wheeler, (1),3 who applies it to that portion of coal resembling charcoal, which he treats as one of the four ingredients of banded bituminous coal. The term has since been adopted by American writers. The Germans use it with slightly different spelling - namely, fusit. It is the equivalent of "mother-of-coal" and "mineral charcoal" of the earlier British writers. The English word fusain is also applied to "a crayon of fine charcoal" and is derived from the Latin root fusus. OCCURRENCE OF FUSAIN IN COAL AND ITS RECOGNITION Fusain is fairly widely distributed in coals of all ranks in varying amounts. It is almost always present in very thin sheets between the bedding planes of the banded coal constituents and presents a jet-black silky appearance who n the coal is split away. As fusain has little cohesive power the coal splits readily along the planes where it occurs. Such fusain bands often attain appreciable thickness -- frequently 1/4 to 3/4 inch. -Beet (2) has reported a maximum thickness of 2 inches for fusain partings, and Sinnatt (3) has found it in the form of plates and lumps; one lump taken by him from the Peacock mine weighed 3-3/4 pounds. Bore (4) has found it in coal balls. Sinnatt (3) states that fusain occurs in two forms, "the first a hard compact variety occurring rather rarely, which can not be pulverized by pressure of the fingers the second type is the common substance" -- that is, a very friable, easily pulverized material. The writer has also found the two types of fusain in the same coal bed and has observed that the hard variety contained considerable calcium carbonate, which probably entered the material in situ by infiltration. Sinnatt further remarks that the layers of fusain (soft type) usually contain less moisture than the coal (or lose it more readily on exposure), and when exposed they quickly change to flocculent powder so that the fines of the coal as mined are likely to contain a major proportion of this substance.

Jan 1, 1929

By H. E. Powell

This study was made to determine the capabilities and limitations of the hydrocyclone for separating quartz sand from impure clays, Optimum operating conditions for beneficiating typical subgrade clays were determined. Estimates are furnished for installation and direct operating costs of hydrocyclones in such separations. Laboratory models of commercial hydrocyclones were used to beneficiate a suite of fire clays including plastic, semiflint, and flint types, all of which were contaminated with quartz in amounts ranging from 3 to more than 62 percent. Results show that this technique is not limited to a single type of clay but is applicable to clays ranging from plastic through flint, Under proper conditions use of this technique will result in good separation of the sand and good recovery of a useful clay mineral concentrate. Rejection of quartz from the clays investigated ranged from a low of 82.4 percent with an alumina recovery of 71.2 percent to a high of 99.0 percent with an alumina recovery of 85.6 percent.

Jan 1, 1963

By A. J. Forney

Recent experiments used catalysts of plate assemblies in synthesizing high-Btu gas and gasoline indirectly from coal. A gas with a heating value of 925 to 943 Bt-: per cubic foot has been prod u la the hot-gas-recycle pilot plant from synthesis gas (3H2+100) with lathe turnings used as catalyst in the first reactor, and assemblies of parallel sprayed plats of nickel in the second. Solid plates made of Raney nickel, and steel and aluminum plates sprayed with Raney nickel or nickel oxide were tested. Those catalysts had very low resistance to gas flow; 90 percent lower than nickel granules used in previous experiments. In a single stage of synthesis thee nickel plates were only partially successful. Although the heating values of the product gas ranged from 856 to 941 Btu per cubic foot, the carbon monoxide content of he gas was above 0.1 percent. Both steel and wrought turnings were tested in single-stage synthesis, but the conversion of hydrogen and carbon monoxide was too low to attain the desired heating value of 900 Btu per cubic foot in the product gas. Assemblies of plates thermally sprayed with fusel iron were tried in an experiment to make gasoline. A gasoline yield of 52 percent (of the hydro¬carbons produced) was obtained using a 1H2-10O feed These sprayed assemblies were in service for 1,500 hours, the longest that this type of catalyst has been used. When a second reactor containing Raney nickel catalyst was added in series with the first reactor, complete utilization of the feed gas was obtained because in addition to the liquid product, a high-Btu gas with a heating value of 800 Btu per cubic foot was made.

Jan 1, 1965

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By Wing G. Agnew

The first six Reports of Investigations in this series , pertaining to the investigation of stemming at the Mount Weather Testing Adit, dealt with ( 1 ) the dust produced by blasting , ( 2) the effect of stemming upon gases generated by blasting , ( 3 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 60 - percent ammonia gelatin dynamite , (4) the length of stemming material through which a primer will fire and detonate a charge of dynamite , ( 5) comparison of dust and gases produced when blasting charges of dynamite in drill holes , bombs, and mud - cap shots , and ( 6 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 40 - percent ammonia gelatin dynamite .

Oct 1, 1943

By M. C. Malamphy, A. H. Reed, G. K. Dale, T. M. Romslo, A. Ollar

"PREFACEA general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourth. The data are accompanied by maps showing the location of holes drilled and the deposits developed.Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township.The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on Figure 13 in Volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes.Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area."

Apr 1, 1948

By J. J. Hoeppner

Lignite samples were collected so as to be widely representative of the extensive deposits in the western north-central area. These were carbonized at temperatures ranging from 450° to 550° C., according, to a standardized procedure. In general, product yields varied; extremes obtained on selected samples show char recoveries on the moisture- and ash-free basis as 56.7 percent for slack lignite or "leonardite" to 80.8 percent for a concentrate of the fusain component from a typical face sample; normal lignite samples averaged approximately 70 percent. Tar-plus-light-oil yields ranged from 3.3 percent for the fusain concentrate to 11.0 percent for a normal sample, averaging approximately 8 percent; gas recoveries varied more widely both in yield and in composition, ranging, from 10.0 percent to 27.7 percent, the latter being from leonardite and quite high in carbon dioxide. Sampling was conducted with the view of representing, as nearly as possible, all beds delineated by Brant (2);4/ many are necessarily missing since collection was confined largely to worked deposits. Data presented in this report indicate a general uniformity of North-Central lignite in respect to low-temperature carbonization, with a few possible exceptions of a local nature. When processed according to the indicated conditions, maximum tar yield may be realized with minimum loss of recoverable heating value of the original coal. Natural weathering of lignite, however, does affect tar yield adversely and should be held to a practical minimum in any commercial operation.

Jan 1, 1956

By John Nagy

Experience and research have shown that an effective way to reduce structural damage from explosions is to provide adequate pressure-relief vents in the walls of equipment and buildings within which explosions might occur. In general, free or unrestricted openings represent the most efficient type of vent. However, in many manufacturing operations it is impractical to use free vents, and it becomes necessary to cover the openings with diaphragms or blow-out disks, hinged panels, or other devices, in order to give protection against weather changes, to prevent the efflux of dusts or vapors from equipment during normal operations, or for other reasons. A few data on the pressure-relieving capacities of hinged panels and a paper diaphragm were published in Bureau of Mines Report of Investigations 3924, which covered the first phase of the dust-explosion venting study made by the Bureau. The present report describes recent experiments that were made to determine the relative effectiveness of an unrestricted vent and 22 types of closures, including various paper, cloth, and metal-foil diaphragms, hinged doors or panels, and several kinds of scored and unscored glass panes. The tests showed that many of the vent closures were effective in releasing the explosions rapidly during their incipient stage, so that the development of destructive pressures was prevented. Vents of this type should prove useful in safeguarding industrial equipment from severe explosion damage. The experiments disclosed that the venting capacities of the diaphragms are approximately inversely proportional to their static bursting strengths.

Jan 1, 1950

By John E. Rourke, O&apos

A survey of existing and developing field permeability test methods was conducted in order to identify and specify capable methods to be used in feasibility investigations or performance monitoring for in situ leaching of ore deposits. Geologic settings of leachable deposits are discussed, as well as representative techniques used for the in situ leaching operation. Subsurface investigation techniques including drilling, core recovery, and down-hole inspection methods relevant to field permeability investigations are discussed. Field experience is examined and capable field permeability test methods are identified. Specifications for test borehole preparation, test performance. and methods of analysis are given. The test methods are comparatively rated in a matrix with respect to costs ease of use, and data effectiveness' for a broad range of conditions. Well Pump and Packer test methods receive high ratings. Recommendations are made for needed developments in field permeability test methods and a comprehensive bibliography is given.

Jan 1, 1977