Search Documents

By A. W. Decora

Gas-liquid chromatography has been applied to separating basic nitrogen compounds, such as pyridines and amines. Close-boiling compounds have been separated by exploiting structural and polarity differences, using selective liquid substrates dispersed on specially prepared solid supports. Development of these special supports was necessary in order to obtain symmetric peaks for basic nitrogen compounds; solution of this problem was important in applying gas-liquid chromatography to the analysis of basic nitrogen compounds found in shale oil. Attempts to analyze shale-oil tar bases by conventional gas-liquid chromatographic techniques, using Chromosorb4/ or Celite 545 as the support for a nonpolar liquid substrate, resulted in asymmetric peaks. These asymmetries were caused by adsorption of sample vapors on the solid support. Symmetric peaks were obtained when strongly polar liquid substrates were used on either Chromosorb or Celite. However, a solid support giving symmetric peaks only with strong polar substrates restricts the choice of substrate, and frequently, desired separations cannot be achieved.

Jan 1, 1961

By A. W. Fahrenwald

The art of flotation has developed rapidly. Numerous technical staffs and individual investigators have, by their combined efforts, developed practicable methods of concentrating ores which ten or even five years ago were considered complex and impossible of commercial treatment. Also the work of those who have been engaged in pure research on the fundamentals of flotation has helped greatly to expedite the general development of the process. However, in spite of the highly successful practical operation of the flotation process, results are obtained and things happen that we are unable to explain completely, although much is known about the theory of the process. The rapid stride in flotation concentration, it is noteworthy to point out, is due to the freer exchange of facts and data by the staffs of the larger mining companies and the patent controlling corporations, and by investigators in general. Generally speaking, one may visit any mining plant and by presentation of proper credentials, be shown all that is going on or that is being done.

Jan 1, 1925

This manual covers the operation and lubrication procedures for the Eimco Pumpable Roof Bolting Machine. This machine meets U. S. Bureau of Mines Schedule 2G Approval. This manual is divided into three major parts: 1. Machine dimensions; 2. operating instructions and; 3. Lubrication. Whenever front or rear, right or left arc mentioned it is assumed that the reader is standing behind the machine looking toward the boom. The boom is at the front of the machine. Safety When leaving machine parked on an incline turn wheels into the rib or block wheels. Do not run over power cables. Make sure your power cable is up out of the way so others can't run over it. Machine has a fire suppressor system for the power unit. The remote actuator (pressure cylinder) is located at the operator's station. Components and service procedures on page 59.

Jan 1, 1976

By James W. Myers

The Bureau of Mines studied factors affecting ignition of coal mine refuse and on methods for control of burning. Laboratory experiments showed that air permeates more readily through segregated than through nonsegregated refuse and that air permeability is greater through coarse than through fine particle refuse. Minus 3-1/4-inch refuse ignites spontaneously more readily than minus 1/4-inch refuse. The burning of a 1,000-pound conical coal pile was con-trolled by capping with an 18-inch-thick layer of minus 1/4-inch refuse containing 37 percent combustible. In field trials, the burning of refuse at operating mines was controlled by capping with a layer of fine refuse. Water, applied as a spray or by injection, quenched surface flames and cooled the burning waste. Inspection of refuse piles at operating mines showed that the spontaneous ignition tendency is affected by the exposed surface relative to the total volume and the segregation of particles during dumping.

Jan 1, 1966

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By J. E. Doo1ey

To process and use the heavy ends of petroleum effectively, the development of suitable separation and characterization procedures not currently available was required. A systematic procedure was developed by the Bureau of Mines using such techniques as isothermal and molecular distillation, chemical treatment, silica-alumina gel chromatography, gel permeation chromatography, and spectrometry. Using these techniques, the Bureau achieved a detailed separation and characterization of a 370° to 535° C distillate from Gach Saran, Iran, crude oil. Such a systematic procedure and the semiquantitative data resulting therefrom should be of value in selecting feedstocks and in optimizing petroleum processing operations.

Jan 1, 1973

By Donald J. Frendzel

The post-World War II expansion of the Soviet petroleum industry has established the U.S.S.R. as a major oil-producing nation and has led to Russian reentry into the international petroleum trade. The rapid growth of Soviet petroleum production will allow the U.S.S.R. to displace Venezuela as the world's second largest oil-producer in 1960 and to narrow further the gap between Soviet and U.S. crude-oil production. U.S.S.R. crude oil output was only a tenth of U.S. production in 1946, but it will be more than a third at the end of 1960 and more than half in 1965. The Soviet Seven-Year Plan (1959-65) for oil provides for substantial increases in petroleum production, refining, storage, and distribution facilities. Crude oil production and primary distillation capacity are to double, considerable storage capacity is planned, and pipelines for crude oil and petroleum products are to increase threefold. According to the Soviets, the initial phases of this plan (1959 and 1960) have been completed successfully. However, this progress has been achieved with difficulty.

Jan 1, 1961

By A. G. Starliper, H. Kenworthy

A procedure was developed for the separation of lead and sulfur in industrial concentrates of galena by a combination of chlorination and fused - salt electrolysis . Galena could not be satisfactorily electrolyzed in the various media tried ; however , when it was treated with chlorine the resulting lead chloride could be effectively separated electrically into lead and chlorine . An apparatus was designed and constructed to chlorinate galena and to volatilize simultaneously most of the chloridized impurities . By electrolyzing the chlorinated concentrate , a high percentage of lead was recovered . Anodic chlorine was drawn from the cell and was used to chlorinate new feed . In many runs , the recovered metal analyzed from 99.8 to 99.9 percent lead . Lead was also distributed as a chloride in the bath , and a small portion was in the volatile fraction produced during the chlorination step . During a tinuous operation , only 0.1 percent of the total lead was discarded ; 99.9 percent was accounted for in the metal , electrolytic bath , and washed or leached chlorination condensate which was essentially lead chloride . About 95 percent of the sulfur from the galena was recovered as a byproduct of over 90 - percent grade .

Jan 1, 1964

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979

By P. V. Fillo

This paper describes Mohave Mining and Milling Co. methods of mining and milling manganese ore in Arizona. It is one of a series of publications prepared by the Bureau of Mines on methods and costs in various mining districts in the United States. Production of manganese ore, as such, in Arizona began in 1915. Before this time manganiferous ores had been mined primarily for silver content and used as a smelter flux. From 1916 to 1918 approximately 69,000 long tons of manganese and mangsniferous ores were mined. After World War I production dropped to almost nothing until World War II, during which period more than 24,000 long tons were produced. A lull in mangonese mining occurred after World War II, having production rates of only a few hundred tons annually through 1952.

Jan 1, 1963

By J. A. Cavallaro

This Bureau of Mines report describes the preparation characteristics of 10 coal samples collected from the significant coal-producing mines of Lucas, Mahaska, Marion, Monroe, and Wapello Counties in Iowa, with special emphasis on physical desulfurization. All 10 samples were of high sulfur content as received, ranging from 4.2 to 10.4 percent; the organic sulfur content ranged from 0.8 to 3.8 percent. The pyritic sulfur content of the samples could be appreciably reduced by crushing and washing and provided pyritic sulfur reductions ranging from 36 to 75 percent. Crushing to 3/8-inch top size and removing the sink 1.60 specific gravity material would provide float coal products containing 3.5 to 6.0 percent sulfur. However, these coals could be burned at utility plants utilizing SO2 removal processes with efficiencies ranging from 70 to 88 percent and still be in compliance with the current Federal SO2 emission regulations for stationary sources.

Jan 1, 1973

By Ott F. Heizer

This paper describing the mining practices at the mines of Massachusetts, Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in tie various mining districts of the United States. The author acknowledges the assistance of William C. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in the preparation of this paper.

Jan 1, 1930

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By John M. Dale

Sulfur is a plentiful, low cost, unique material whose physical properties can be altered and employed in structural applications. This program was undertaken to develop an optimum sulfur based formulation for use as a coating to both seal and support mine walls. The initial effort in the program was devoted to a laboratory study of the physical and mechanical properties of a variety of sulfur base coatings that were specifically formulated for this application. Concurrent with formulation development, laboratory equipment and techniques were developed for spray applying the sulfur based coatings to the ceiling and walls of a structure that simulated the interior of a mine. Much of the formulation work was guided by the experiences encountered when attempting to spray the formulations overhead. One hundred parts of sulfur modified with 10 parts of talc, 3 parts of milled glass fiber, and 2 parts of dicyclopentadiene was found to be a fire retarded, low odor, low eye irritation, sprayable formulation for sealing and strengthening mini, walls. An invention disclosure on this formulation was submitted to the Bureau of Mines and a patent application was filed. Various mineral samples were obtained and adhesive strengths of the formulation to these samples in both the wet and dry state were measured. With the development of an attractive sulfur based coating material, attention was directed to the design, fabrication, and testing of a portable spray application unit so that coatings might be applied in the field to various rock surfaces and earth formations for further evaluation. The unit was fabricated in the Southwest Research Institute shop. Once operational, the unit's capabilities were field tested and demonstrated at three separate locations. Upon completion of the field testing, the unit was shipped to the Spokane Mining Research Center where Bureau personnel were instructed in the use of the unit.

Jan 1, 1972

By P. D. Laverty

This report describes a processing method developed by the U.S. Bureau of Mines to produce high-quality flake graphite from the steelmaking waste known as kish. The kish produced by current steelmaking practices is a mixture of graphite, desulfurization slag, and iron that is skimmed from the molten iron feed to the basic oxygen furnace. It is estimated that the graphite content of kish discarded by U.S. steel plants is more than sufficient to meet the total U.S. demand for flake graphite. That need is now filled by natural graphite from foreign sources. Kish was treated by a combination of screening and hydraulic classification to produce a concentrate containing greater than 70 pct graphite. Leaching of the concentrate with hydrochloric acid solution gave a graphite product with 95-pct purity. An optional secondary leaching operation with hydrofluoric acid produced graphite with a purity of 98 pet or greater. The flake size of graphite from kish ranged from 10 mesh down. Evaluation of test samples by industrial graphite users indicated that kish graphite is a suitable substitute for the natural material for most uses. A process flowsheet and material balance for pilot plant design are presented.

Jan 1, 2010

By Sam S. Taylor, H. M. Smith

"INTRODUCTION In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas Produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used.Although P.ir is a Cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called ""bad gas""--return,mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory--scale study of direct oxidation of crude oil."

May 1, 1934

By Harry R. Johnson

Domestic expenditures by the U.S. petroleum industry have exhibited distinctive shifts in emphasis over the past 20 years. From the end of World War II to 1955, expenditures for all phases of the industry expanded. Although over one-half of all expenditures were for production, the relative emphasis was changed after 1956-58 from production toward processing and marketing. The period 1967-69 marked the beginning of a return to emphasis on exploration and production. These trends in expenditure patterns are logical and rational when related to domestic and international economic conditions and to the widespread application of improved production technology. As the immense job of developing the oil resources of Alaska and other regions begins, the petroleum industry will continue to turn to external sources for working capital. Long-term debt will probably be the principal method of external financing through 1970, but a definite shift toward new common and preferred stocks will be made. Higher product prices may be sought by the petroleum industry, but the economics of crude-oil production, changes in the tax structure, and possible changes in the oil imports control program make the price structure of crude oil and crude-oil products unpredictable at the present time.

Jan 1, 1970