Search Documents

By Martin J. Gavin

The oil- shale studies of the Bureau of Mines , conducted in cooperation with the State of Colorado and the University of Utah , have for their primary purpose the determination of retorting and refining conditions most favorable for obtaining the highest yields of most satisfactory products . Oil shales , typical of the deposits in several States , are retorted in carefully controlled retorts of differe types , the conditions being varied in successive runs as the results indicate that improvement in the yield and quality of the products most desired may be expected . Each shale presents a somewhat different problem , for it has been found that different shales treated under similar conditions yield products of different natures , and also that the same shale will yield products of different natures when retorted under different conditions . Some shales apparently can not be made to yield , under any set of conditions , products of so high an order as are yielded by other shales . This indicates that the oil -yielding materials of certain shales differ in constitution and in their manner of breaking down when undergoing destructive distillation . Other shales appear to contain oil - yielding materials that resemble each other closely as regards chemical constitution , yet they require some. what different conditions of treatment , if products of similar nature are to be produced from each . In such cases the controlling factors seem to be the richness of the shale that is , its content of oil -yielding material and the physical and chemical nature of its mineral parts .

Mar 1, 1922

By Eric R. Bauer

The ground control aspects of extended depth-of-cut mining are presented in this U.S. Bureau of Mines report. A trend analysis of extended cut approvals was performed. A comparative review of roof fall fatalities for extended and nonextended cut mining is included. Current ground control guidelines for extended cut approval are summarized. The problems and concerns of this extraction system are addressed, and typical extended cutting face operations are described.

Jan 1, 1993

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By Oliver Bowles

Limestone, including dolomite, is the most widely used of all rocks - nearly 300 million tons annually in the United States alone. It occurs in some form in every State and is produced in thousands of localities. Because of its attractiveness, substantiality, and durability it is employed extensively as a building stone. In crushed and broken form it is used for concrete aggregate and railroad ballast and in highway construction, metallurgy, agriculture, and a host of chemical and industrial processes. This paper proposes to furnish general information on the origin and occurrence of limestone and dolomite, chief production centers, major uses, and methods of quarrying and preparing stone for market. Footnote references will guide the reader to sources of more complete information.

Jan 1, 1956

By J. Douglas Causey

No mines are active in the Hunter Mountain Wilderness Study Area (WSA), and no mineral resources have been identified in the WSA. However, the Monarch Mine has low potential for silver, copper, tungsten, and gold resources in quartz veins; the Shirley Ann Group and Sal Group have moderate and low potential, respectively, for silver, lead, and copper resources in skarn; claims overlying the Eureka Quartzite have low potential for silica resources; and the Tourmaline N1-4 Prospect has low potential for tourmaline resources in quartz monzonite. Copper, lead, silver, tungsten, molybdenum, wollastonite and garnet occur in skarn zones between monzonitic and carbonate units. Silver, tungsten, and copper also occur in quartz veins within monzonite. Known metallic mineral deposits are small, erratic and discontinuous. The J. 0. Mine, adjacent to the northeast corner of the WSA, may contain as much as 26 million tons of subeconomic wollastonite resources. The crest of an open pit to produce that resource would extend into the WSA. No information exists on geothermal potential because no exploration has been done in the area. No occurrences of energy minerals are known within the WSA.

Jan 1, 1983

By S. H. Ash

The Pennsylvania anthracite-mining region is the only one in the world of major magnitude. As the deposits of anthracite in the United States are limited virt113.lly to Pennsylvania, the difficulties of this industry have been commonly considered a State rather than a national problem. However, there is also national interest in the conservation and wise utilization of all fuel resources and in the control of interstate waterways. The anthracite industry is confronted with the very se:;-ious :problem of accumu.lation of water in many of the mines. This problem must be solved soon if progressively higr-er mi~ing costs are to be avoided. The water proble~ cannot be solved by the operating compa,nies without State or Federal aid, or both, owing to the magnitude of the work requir~d, diversity of interests of the coal ana surfa.ce ovmerships, hazard to the whole mining community, and interests affec~ed outside the mining region. The cost of abati~ the ever-increasing_surface seepage to mine workings and of handling this seepage once it }3s occurred is beyond the economic resources of most ope~ating ma.'18.gements. The data in this paper giving the high lights of the water problem and indicating what appears to be a step in the right direction are based upon observations made during the past year that the industry desires and believes it is to the npublic interesttr to keep mine workings free of flood end surface waters.

May 1, 1941

By L. B. Berger

Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the dangers of this gas, and frequent now items retort the finding of persons dead or unconscious from the effects of carbon monoxide, yet these accidents continue. Either those warnings are not read, or they are unheeded by people who feel that "It can't happen to me." It can happen to you - carbon monoxide is no respecter of persons, as evidenced by items appearing daily in newspapers all over the country. Carbon monoxide has been a threat to human safety as long as man has used fire to keep himself warm and to cook his food. The burning of any fuel that contains carbon may produce carbon monoxide. This is true of solid fuels such as coal, coke, and wood; of liquid fuels such as oil, gasoline, and kerosene, and of gaseous fuels such as natural or manufactured gas. In the process of combustion the carbon in the fuel unites the chemically with tat oxygen of the air to form carbon dioxide (CO2), however, if the supply of air is not adequate, combustion is incomplete and carbon monoxide (CO) will be formed.

Jan 1, 1943

By M. J. Beus

The U.S. Bureau of Mines is conducting investigations to improve design methods for mining volcano-genic massive-sulfide (VMS) type deposits in environmentally sensitive regions. This study was conducted at the Greens Creek Mine, which is typical of many VMS-type deposits throughout southeast Alaska, and served as a case history for computer modeling and structural analysis. Results indicated that the finite-element design method provided reasonable comparisons with both the anticipated regional stress regime and the measured deformational response of the underground accessways. Investigators concluded that reasonable accuracy can be expected for stability analyses of proposed mine design scenarios at this mine using the results of this preliminary study.

Jan 1, 2010

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

By H. D. Jacobs

The Federal Bureau of Mines, as part of a program to insure future raw material needs for the iron and steel industry, undertook research to beneficiate the oxidized taconites from the western Mesabi range in Minnesota. The data presented were obtained by applying the Bureau-developed selective-flocculation/cationic-flotation process to the second of three oxidized taconite samples. These three samples are representative of an estimated 10 billion tons of ore analyzing 30 to 40 pct iron. The experimental work was performed in a 900-lb/hr pilot plant. Treating the ore sample (36.1 pct Fe) with the Bureau's process produced commercially acceptable concentrates averaging 63.5 pct Fe and 4.3 pct SiO2, with an average iron recovery of 84.6 pct.

Jan 1, 1980

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Hsin Wei Wu

A real-time Diesel Particulate Matter (DPM) monitor has been developed on the basis of the successful National Institute of Occupational Health and Safety (NIOSH) designed Personal Dust Monitor (PDM) unit. The objectives of a recently completed Australian Coal Association Research Program (ACARP) study were to modify the PDM to measure the submicrometre fraction of the aerosol in a real-time monitoring underground instrument. Mine testing focused on use of the monitor in engineering evaluations to determine how conditions can be improved. Studies, including a selection during Longwall (LW) moves as described in this paper, demonstrated how DPM concentrations from vehicles fluctuate under varying ventilation and operational conditions. Correlation between the current SKC DPM measurement system and real-time DPM monitors were conducted and results from six mines show a correlation between elemental carbon (EC) and the new monitor DPM mass ranging from .51 to .81 with R2 >.90. These differences are suspected to be due to variations from mine to mine in aspects such as mine atmospheric contamination, vehicle fleet variations, fuel type, engine maintenance, engine combustion efficiency, engine behaviour or interference from other submicrometre aerosol. Real-time monitoring readily reflects the movement of individual diesel vehicles and allows pin-pointing of high exposure zones such as those encountered where various vehicles work in areas of constrained or difficult ventilation. DPM monitoring approaches that have been available for some time based on shift average monitoring do not readily allow successful engineering evaluation exercises to determine acceptability of pollution levels. Identification of high DPM concentration zones allows efficient modification of mine ventilation, operator positioning and other work practices t o reduce miners? exposures without waiting for laboratory analysis results.

Jan 1, 2010

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests.

Jan 1, 1957

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindablity index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous of coal as delivered is a check on the practical results obtained in the coal.

Jan 1, 1967

By W. H. Hamilton

The Kokomo (Tenmile) mining district has had an output valued between $20 and $30 million, mostly from production of silver, lead, and zinc, since 1878. For many years before World War II, there was little production, as the complex nature of the ores made them unattractive at existing metal prices. Under the stimulus of the war, the Geological Survey and the Bureau of Mines studied they district, and in October 1944 the Bureau of Mines began an exploration project, which included dia¬mond drilling, bulldozer trenching, and geophysical surveying. Project work was continued until March 1949, except for short recesses during 1945, 1947, and 1948. Forty-five diamond-drill holes, totaling about 13,000 feet, were drilled from underground and surface stations on the various properties in the district. Eleven bulldozer trenches, abut 2,400 linear feet, were excavated in an attempt to uncover the outcrop of the middle Quail limestone. These trenches ranged from 100 to 485 feet in length and reached a maximum depth of 15 feet. A limited geophysical investigation was made during the summer of 1946. The length of the traverses were: Magnetic, 990 feet; resistivity, 6,250 feet; and self-potential, 69,780 feet.

Jan 1, 1955

By L. E. Schultze

Experiments were conducted by the U.S. Bureau of Mines to verify enhancements due to chloride and surfactant additions in the leaching system of chalcopyrite with ferric sulfate and sulfuric acid. A statistical experimental design was used and equipment was designed to eliminate contributions from changes in solution electrochemical potential during the course of the measurements. Results confirmed that chloride additions increased chalcopyrite leaching by as much as 94 pct over the electrochemical potential versus hydrogen electrode range of 630 to 750 mV at pH 1.7 and 50°C. Total iron concentration had no effect over the range of 1 to 5 g/L. The effect of surfactant addition was less well defined. While additions of LA 790 (a polyoxyethylene lauryl ether) resulted in increased copper leaching in several of the tests, the differences were too small to be statistically significant. No interaction effect could be verified.

Jan 1, 2010

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Ergonomics processes described in the literature have been associated mostly with manufacturing, financial, electronics, and office settings where working conditions tend to be rather constant and repetitive. The information presented in this document demonstrates, however, that an ergonomics process can also be implemented in a setting such as mining where working conditions frequently change and workers are periodically exposed to extreme weather conditions. This document describes how Bridger Coal Company implemented an ergonomics process at its Jim Bridger Mine from 2001 through 2004. The process developed by the Ergonomics Committee, the promotion of the process to management and employees, and the impacts of the process on working conditions at the mine are reviewed. Barriers overcome and lessons learned are also described. Quotes from Bridger Coal Company employees are included in the document to add a personal perspective. Other industries with working conditions similar to mining, such as construction and agriculture, may find this information useful.

Jan 9, 2006

By Clinton C. Knox

During the latter part of 1943, a magnetometric survey was conducted by the Geophysical Division of the Bureau of Mines at the Mahopac magnetite mine, Putnam County, N. Y., in an endeavor to locate a segment of the ore body that reports state was cut off by a fault. The Mahopac mine was abandoned about 1895 after producing nearly 1,000,000 tons of high-grade magnetite iron ore. The results of the investigation indicate the termination of the ore body by "pinching", or a displacement of such magnitude as to place any extension at a considerable distance from the original are body. This report describes the work done on the project and presents the data obtained.

Jan 1, 1948