Search Documents

By W. A. Selvig

[THE BUREAU OF MINES receives many requests for information regarding the low-temperature carbonization properties of American coals. This report presents in collected form the results of Fischer-Schrader bench-scale, low-temperature carbonization assays at 500° C. made by the Chemistry and Physics Section at the Pittsburgh station of the Bureau of Mines. Most of the assays were made of coals tested in connection with a survey of gas and coke-making properties of American coals,4 which was started in 1928 by the Bureau in cooperation with the American Gas Association. Other coals were assayed in connection with miscellaneous investigations. Since 1930 about 400 samples of coal were assayed from nearly every coal-producing State, Alaska, and British Columbia, Canada. The results of the tests on about two-thirds of the coals are scattered through more than 50 separate publications. This paper summarizes the data in the published reports as well as all unpublished data obtained to January 1, 1956. The report also includes a detailed description of the procedure used in making the assay.]

Jan 1, 1957

By N. S. Raymon

As part of an interegency agreement with the Energy Research end Development Administration to develop unproved refractory materials for use in coal gasification processes, the Bureau of Mines reviewed the literature to determine the effect of steam, H2, CO, and CH4 as well as the alkali metal oxides K2O and Na2O on refractory materials. Emphasis was given to the performance of high-alumina castable and fired refractories to conditions expected in coal gasification processes. Approximately 85 references were reviewed with 40 cited in the text. The literature was found to contain little data directly applicable to the selection of refractory lining materials suitable for use under the conditions of temperature, pressure, and gas compositions expected in second generation coal gasification reactors.

Jan 1, 1976

By Arnold O. Tanner

The recession that took hold of the domes-tic mining industry in 1981-82 finally abated somewhat in 1987, resulting from increases in many commodity prices, especially in the metals sector, and from continuing success in lowering operating costs. By no means was the work finished; the mining industry was in a sense entering a new era. The struggle for survival was still very evident for many companies and various commodities, but increasing productivity and profits were accompanied by indications that these trends were more long term than short term. Raw nonfuel minerals produced in the United States during 1987 had an estimated value of $26.3 billion, an increase of $2.9 billion over the 1986 value. This is the fifth consecutive year that the value has increased. Except for a decrease in 1982, the value each year has increased since 1971, or 15 of 16 years. The value of raw metals production increased by an estimated 28%, an impressive improvement since the drastic fall in 1982. Industrial minerals growth was comparatively flat, with an estimated in-crease in value of 0.1 %, continuing a trend of the previous 2 years. Metal mine production dropped considerably in 1982 and maintained its resultant lower level until 1987, when production significantly recovered.

Jan 1, 1989

By W. J. Kroll

Despite the fact that barium minerals are plentiful and widely distributed in nature, this element is one that we do not yet know how to prepare cheaply in metallic form. This is due to its chemical activity, as evidenced by its great affinity for fluorine, chlorine, oxygen, nitrogen, hydrogen, and sulfur. Furthermore, it forms a very stable subchloride and subfluoride, which prevents isolation of the metal by fusion electrolysis from a halide bath. A good survey of the metallurgy of barium calcium, arid strontium has been made recently in Light Metals (54,55).3/ Metallic magnesium (46), calcium (83), barium, and strontium (27) reduce each other's oxides. Proof of this can be found in the activation of BaO after reduction with Mg, which leads to the formation of so-called "Maquenne" mixtures (58) used for absorbing gases. However, it is impossible to extract the reduced metal- from the residue, a fact that Guntz (25) attributed to the formation of barium suboxide. There is no necessity for presuming the formation of such a compound, as it has boon established that in the reduction there is always formed an alloy of the alkaline-earth metal with the magnesium, which is capable of producing hydrogen when brought into contact with water. The reduction of alkaline earth-metal oxides with aluminum was observed by Mallet (57) in 1877, but recent investigations have shown that the end product of the reaction is an alloy of aluminum with the alkaline earth metal (1,2). Silicon also has been suggested as a reducing agent, and the results obtained are the same (84,85).

Jan 1, 1945

By J. B. Gayle

During the past several decades, there has been a steady increase in the number and size of experimental ovens used for carbonization research. Although many were originally intended principally for studies of coal expansion, current practice usually includes determinations of the properties of the experimental cokes. With respect to size and shatter characteristics, the cokes from the larger experimental ovens closely approximate those from duplicate charges carbonized in commercial ovens; however, they are consistently lighter and frequently less resistant to degradation by abrasive forces. To minimize these differences, some operators dry the experimental charges before carbonization. The resulting higher dry coal charge densities do, in fact, yield cokes with gravities closely approximating those produced commercially from the same coal or blend but without drying. The drying of the experimental charges may be criticized on the grounds that it represents a departure from commercial practice and may result in oxidation of the samples; for these reasons, the practice has not been universally adopted.

Jan 1, 1961

By Erle C. Donaldson

Bureau of Mines engineers examined the chemical and biological treatment of sewage water designed in one case for reuse and in another for subsurface injection. In the first case discussed, approximately 6 million gallons per day of sewage are treated by the activated sludge process followed by tertiary treatment that includes ion exchange. The renovated water is used in the industrial complex. Liquid industrial waste is sent to a waste disposal facility where it is treated for injection into a deep subsurface formation. In the second case, a community of 3,000 people is using a lagoon sewage treatment system followed by subsurface injection of t- treated effluent. Subsurface disposal is used to avoid growth of algae and weeds in a nearby lake to which the treated effluent was originally discharged. The renovation of municipal water for reuse provides a source of water for industries in a semiarid region and may also provide a source for domestic use in densely populated regions where domestic water requirements have priority over industry needs. In addition both waste treatment systems provide examples of the use of subsurface waste disposal to avoid pollution of surface streams.

Jan 1, 1971

By F. E. Block

The metallic reduction of vanadium chlorides was investigated by the Federal Bureau of Mines as a possible new route for preparing vanadium metal in an effort to develop a production process that would be adaptable to large-scale plant production and would yield metal of uniformly high quality. Vanadium tetrachloride was usually prepared by chlorinating vanadium pentoxide in the presence of carbon. Although oxygen-?free tetrachloride was difficult to prepare this way, it could be prepared by the direct chlorination of vanadium carbide. Lower valent vanadium trichloride was prepared by the thermal decomposition of vanadium tetrachloride. Vanadium dichloride was also prepared by the thermal disproportionation of vanadium trichloride.

Jan 1, 1961

By Henry P. Cole

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/technical workplaces are described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training is explored. Research and development activities that may improve mine health and safety training are suggested. Most of these research and development activities were completed later in the project. This additional work is reported in the project technical report #2 and the final report. The research reported in the present document was completed in 1984 -85. Many of the initial findings reported in this document are updated in the later project final report.

Jan 1, 1988

By Wm. W. Odell

For a number of years there has been a very appreciable annual,, increase in the production and recovery of natural gas and natural-gas gasoline2 in the United States the latter product being used largely for blending with gasoline from petroleum in the production of motor fuel. On account of the increased amount of oil cracking in the production of gasoline and the accompanying increased percentage of low-boiling constituents in the resulting product, the specifications for the natural gasoline suitable for blending have been altered, that is, the amounts of propane and butane which it can contain have been limited. The result has been that large quantities of the latter materials are wasted because there has been no ready market for thorn in large quantities. Because of this wasteage and because it is probable that large quantities of there and similar materials will be produced in the near future us a result of the more general use of oil cracking processes, a study was made by the Bureau of Mines, under a cooperative agreement with the assistance of the Phillips Petroleum Company, of the suitability of these materials alone or in mixtures for use as gas enricher in the carburetion of water gas for city distribution. This investigation included: (a) A study of the properties of the low boiling members of the paraffin series including pentane with particular reference to their utilization as gases.

Jan 1, 1927

By R. V. Lundquist, H. Leitch

The solubility characteristics of three calcium aluminates , 12Ca0 · 7A120½ 3Ca0 A1203 , and 4Ca0 A12 03 Fe2O3 , were determined in water and in solutions of NaOH and Na₂ CO₂ to more clearly define their role in relation to the recovery of aluminum by the lime sinter and the lime - soda sinter processes . The calcium aluminates were prepared by sintering stoichiometric mixtures of CaCO3 , Al2O3 3H20, and Fe 0 at 1,375 ° C. The rates and extent of aluminum extractions were determined . The aluminum extractions from the aluminates were dependent on the presence of carbonate ions in the leach solutions , temperature , time , leach solution composition , and solid - liquid ratio of the slurry . The aluminum extracted from the calcium aluminates in water and in NaOH solutions varied from 4.6 to 22.9 percent . Virtually , complete extraction could generally be obtained for 12Ca0.7A120 and 4Ca0.A12 03 • Fe₂ 03 ; in one instance it was obtained for 3Ca0.A1203 , when an excess of carbonate ions was present over that required for the conversion of all of the calcium in the aluminates into CaCO3 . In some cases of poor aluminum recoveries , extractions could be improved by regrinding and releaching the solid residues .

Jan 1, 1964

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

By L. K. Weaver

Bureau of Mines investigated the progressive impact that petroleum (crude oil and condensate) operations in the Gulf of Mexico have had on onshore operations and the expected effect of increasing activities in this area on future petroleum supplies from domestic sources. The data analyzed include capital expenditures, number of wells drilled, success ratio for exploratory wells, daily production per completion, annual producing rates, and oil reserves. The report compares offshore and onshore data and ascertains trends in petroleum industry operations. Observed data and trends indicate that in the near future Gulf of Mexico development and production will continue to increase relative to total U.S. petroleum activity. By 1975 annual oil and condensate production from the Gulf of Mexico is expected to be in the range of 750 million bbl to 1,150 million bbl, and account for approximately 20 to 30 pct of the estimated total domestic production.

Jan 1, 1969

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

By Charles F. Jackson

Waste filling has been employed for many years for supporting the walls of stopes and preventing failure and subsidence of the surrounding and overlying rock formations, and its effectiveness for this purpose has long been recognized. It is used for permanent support in ground where timbering (including square-setting) is inadequate for more than temporarily supporting the walls of the excavations. It should be rioted, however, that effective as a good, solid fill may be in resisting heavy side pressure and direct weight, its usefulness for supporting large areas of back and preventing breaking and movement of the overlying rocks is limited. Even the strongest and most uniform rocks will break if the unsupported span becomes too great; and since filling cannot be packed tightly against a horizontal back there is always a possibility of the back breaking and consequent subsidence if the maximum self-supporting span is exceeded. Planes of separation, such as bedding and fault planes, slips, and joints, are common in all rock masses; these may occur above the stoping area where their presence cannot be ascertained by observation. If too much reliance is placed upon filling for the support of a large horizontal area of back (as contrasted to support of vertical or steeply inclined walls) large masses of rock may break along a. plane of weakness, compress the fill, and leave an open space into which caving of the overlying rocks may continue until the space is filled. In this paper the term "waste filling" includes any filling material other than ore - waste mine rock, rock from surface quarries or opencuts, sand and gravel, mill sands, or slags from smelting operations.

Jan 1, 1935

By Thomas A. Morgan

The distribution of stress adjacent to each of 25 mine openings was determined by the borehole stress-relief method in the FMC Corp. Westvaco trona mine at Westvaco, Wyo. The purpose of the stress determinations was twofold: First, to study the effect on these distributions of various factors such as opening shape, stress level, and loading history; and second, to estimate the distribution of stresses adjacent to extensive high-extraction (85 to 100 percent) areas. Stress distributions in areas of low average stress correspond closely to the theoretical distributions based on elastic theory. However, in areas of high average stress, the stress distributions are of a type associated with plastic failure. The stresses adjacent to a mined-out area supported by remnant pillars were significantly higher than the stresses adjacent to another area in which the remnant pillars were removed.

Jan 1, 1965

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By FREDERICK H. WILLCOX

In the past the blast-furnace industry was under the stigma of being one of the most prolific sources of killed or seriously inj ured and permanently disabled workmen of any of the industries of the country. In the popular mind, labor at blast furnaces was little less hazardous than mining, powder making, or railroad work. This impression wasbased not so much on definite knowledge of the number actnally injured and the causes of injury as on the spectacular nature of the accidents that from time to time were described in the press. As with a mine disaster or a railroad wreck so with many furnace accidents, the number fatally injured in such accidents constitutes only a minor proportion of the workmen who suffer more or less serious injuries. However, the reader of the daily paper receives a distinct impression-of frightful and sudden disaster which is apt to be associated henceforth in his mind with work at blast furnaces. It is true that in the past this impression has not been without warrant, for from the time of the advent of Mesabi ores, taller furnaces, and faster smelting, which begain in the early nineties, the newspapers have chronicled a large number of blastfurnace disasters. Blast-furnace men have never assumed to tolerate failures in construction or defective control of furnaces. But the admitted hazards of the work are many, and the slow development of improvements in the construction and control of the furnace and its auxiliaries have occasionally given rise to a tendency to accept as a part of the day's work not only the unforeseen and difficultly controlled accidents but accidents whose recurrence might be stopped by the adoption of suitable preventive measures. In the smelting of iron, even more than in many other industries, safety is inseparably related to efficiency in production, and. the accidents strictly incident to work about the furnace are proportional in some degree to the success with which obstacles to smooth working are overcome. This relation does not hold, however, in regard .to such accidents as are incident to hand labor, falls, falling and flying objects, machinery, and the use of hand tools.

Jan 1, 1917

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982