Search Documents

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two- thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines collected and analyzed overcore measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 2010

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July l, 1936.

Jan 1, 1940

By George T. Motock

The author prepared the following report as the result of a trip to Germany in the summer of 1945 for the Technical Industrial Intelligence Commitee Subcommittee on Metals and Minerals. The purpose of this committee, which functions under the Joint Intelligence Committee of the Joint Chiefs of Staff of the United States Armed Forces and of which the Bureau of Mines

Jan 1, 1946

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau's interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937

By O. S. North

As recently as the late 1920's there Were few indications that a 15-million-dollar-a-year industry would ever grow out of the mineralogic curiosity vermiculite. Today, it is an important industrial commodity, used primarily as an insulating material and lightweight aggregate, but with a wide range of other applications. The quantity of crude vermiculite produced and used in the United States increased 14-fold in the 17 years between 1935 and 1951. The vermiculite minerals are of secondary origin, formed by hydrothermal alteration of an ultrabasic igneous rock, generally pyroxenite, or by alteration of phlogopite or biotite mica or possibly other similar minerals. According to different authorities, vermiculite may originate either by direct hydrothermel means, by the weathering of biotite or phlogopite, or by a combination of these two agencies. Vermiculites frequently occur at or near the contacts of an acid intrusive rock, especially a pegmatite dike, with a basic or ultrabasic country rock.

Jan 1, 1953

The Government of New South Wales has granted approval for Hunter Valley Aluminium Pty., Ltd" and Alcan Australia Ltd. to proceed with the building of an aluminum smelter at Lochinvar and the expansion of a smelter at Kurri Kurri. Construction of the smelters is expected to start as soon as the consortium is finalized in early 1982. The smelters are part of a plan to increase Australia's aluminum capacity fivefold to 1.5 million tons by the mid-1980's. CHILE Construction of a $61 million lithium carbonate plant in northern Chile will be started in early 1983 by Sociedad Chilena del Litio Ltdao Production is scheduled to begin in 1984 with an initial capacity of 6,350 tons of lithium carbonate produced from a brine deposit. The firm is owned 55% by Foote Mineral Company, of Exton, Pennsylvania, and 45% by Corporacion de Fomento de la Produccion-CORFO.

Jan 1, 1982

By P. Nicholls

Patent records show that the idea that the burning of fuels can be improved by mixing or pretreating them with chemicals 6 dates back to the early years of the last century. By 1845, English and French patents included the specific beneficiations of elimination or reduction of smoke, soot, and clinker; reduction of the ashes, presumably meaning the total weight of refuse from the ashpit; elimination of sulphur fumes; increase in the rate of burning; increase in the time a given charge of fuel would last; and, in most patents, a saving of fuel. The earlier patents specified additions up to 80 pounds or more per ton of fuel, but after 1860 the quantity was rarely more than 4 pounds. There is no record of the extent to which these patents were commercialized, but after 1884 many American patents were assigned to companies specializing in treatment of coal, so it is probable that the products were marketed on a considerable scale at least as early as that date. From 1900 on, many companies marketed proprietary products that were sold under the general name of "fuel savers." Since its establishment in 1910, the Bureau of Mines has continually received inquiries about these products and, at the request of other govern-mental departments, has tested some used in accordance with the instructions of the purveyors; the results were all negative and, within the accuracy of measurements, the products had no effect on the burning.

Jan 1, 1937

By William E. Dennis

"At the request of Philip S. Hoyt, the Eagle Mountain fluorspar deposits in section 35, block 68, Texas & Pacific Railroad Survey No. 9, were examined by an engineer3/ of the Bureau of Mines during March 1943: As a result of this examination; a preliminary program of trenching, sampling and core drilling by the Bureau of Mines was begun in. June 1943.4/ Eight deposits were explored.The Federal Geological Survey mapped the properties and furnished geologic information throughout the program, while the Texas .Bureau of Economic Geology6/ made preliminary maps that facilitated planning the exploratory work on section 35.The eight deposits explored by the Bureau of Mines are in block 68, Texas & Pacific Railroad Survey No. 9, Hudspeth County, Tex., approximately 7-1/2 miles south of. Hot Wells and 12-1/2 miles south of Allamoore, which is 10 miles west of Van Horn and 20 miles east of Gierra Blanco on U. S. Highway 80(fig. 1). A graded gravel road, built by the Public Roads Administration, leads from Hot Wells to the deposits in section 35, and there are unimproved roads, passable,by automobile, to all the other deposits.Carload shipments can be made to and from Hot Wells on the Southern Pacific Railroad, and complete railroad facilities are available at Allamoore on the Texas & Pacific Railroad.Van Horn and Sierra Blanca are the only local source of labor and. supplies. The prevailing wage for common labor is 60 cents an hour. Living accommodations are obtainable in Horn and Sierra Blanca.No electric power lines pass near the deposits. Diesel and gasoline motors are employed to furnish power for mining and milling operations.Two recently 'drilled water wells on section 35 furnish water for the mill. Other wells will be drilled if the present supply is inadequate for prolonged Peak operation.The properties lie in the foothills on the northeast side of the Eagle Mountains at 5,500 feet altitude. The Eagle Mountain Range rises sharply from a broad, flat valley known as Eagle Flat. Eagle Peak, the highest in the range, has an altitude of 7,510 feet. In the vicinity of the fluorspar deposits the topography is moderately reliefs ranging from 50 to 300 feet."

Jun 1, 1946

By J. J. Forbes

Since 1910 the Bureau of Mines has given training in the care and use of oxygen breathing apparatus under conditions that may exist during mine fires and after mine explosions. In 1929 the Bureau supplemented this instruction by initiating a course in advanced mine rescue training to prepare mine officials and others to organize men for mine rescue and recovery operations. The course of instruction has been developed and expanded since its inception to keep abreast with new ideas, methods, and equipment. Four miners' circulars were issued to be used in the training course. The first of this series (Miners' Circular 33) deals with mine gases and the various methods of detecting them; the second (Miners' Circular 34) gives instructions for sampling and analyzing mine atmospheres; the third (this circular) describes methods and equipment for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures in sealing and unsealing mine fires and in conducting recovery operations, These circulars have been revised from time to time to keep them up to date.

Jan 1, 1954

By Jeffrey Y. Foley

In 1980, the Bureau of Mines investigated the northern Darby Mountains on the Seward Peninsula, AK, for radioactive mineral deposits. Uranium is concentrated in silicified shear zones in biotite quartz monzonite of the Darby pluton. The shear zones are best exposed in steep, narrow, avalanche gullies; they are characterized by radiometric anomalies and by uranium and thorium geochemical anomalies. Radiometric and geochemical anomalies are also found over altered biotite quartz monzonite where there are no visible shear zones. The radiometric and uranium anomalies are often spatially, but apparently not genetically, associated with alkaline mafic and felsic dikes. Similar geochemical and radiometric anomalies over discolored altered zones and geochemical anomalies in sediments downstream from the altered zones indicate that additional areas may also be favorable targets for uranium deposits. Analyses of panned, heavy mineral concentrates show no significant concentrations of uranium or thorium in resistant heavy minerals. This indicates that radioactive elements in the Darby pluton are concentrated in soluble, nonresistant minerals that may constitute a recoverable uranium resource.

Jan 1, 1986

By E. H. Rose

This paper, describing the concentrator practice of the Moctezuma Copper Co., is one of a series being prepared by the Bureau of Mines. The Nacozari concentrator of the Moctezuma Copper Co. (the Mexican subsidiary of the Phelps Dodge Corporation) is located about 75 miles south of Douglas, Ariz., in the Moctezuma District of the State of Sonora. Nacozari is the southern terminus of the Nacozari Railroad, ever which all concentrate is transported to Douglas for smelting.

Jan 1, 1930

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By J. J. de Barbadillo

This report describes a process for recovering chromium and other metals from superalloy scrap. Part I contains the results of laboratory scale experiments which were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the formation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallugical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and an iron-molybdenum residue. Recovery of the principal elements contained in the scrap are chromium(Cr)-93 percent, nickel(Ni)-99 percent, cobalt(Co)-96 percent, molybdenum(Mo)-92 percent. Part II encompasses a preliminary engineering design of a pilot plant capable of treating 100 pounds(lb) of superalloy scrap per hour. Also included is an economic analysis of the operation of the pilot plant.

Jan 1, 1980

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By Roy A. White

The development of a fire and rot-resistant coating treatment for mine timbers, along with the associated processing technology, is described. Included are a literature search, laboratory studies of polyimide-fungicide coatings, and leaching and fungus growth studies on coated wood blocks. Finally, an economic analysis is performed tor various levels of production.

Jan 1, 1977

By William H. Waggaman

The United States not only is the largest producer of phosphate rock but also manufactures and consumes greater quantities of phosphate products than any other country. New and expanding uses will increase even further the demand for this basic raw material. Only a small proportion of the total quantity of phosphate rock mined and marketed is consumed directly in a raw or unprocessed state; the vast bulk is chemically treated and converted into [ertilizer] and a wide variety of finished products that play a vital role in [r] national economy. Three fundamental methods are employed in decomposing phosphate rock. 1. Reduction by carbon at high temperatures. 2. Treatment with one or more acids. 3. Calcination or fusion with silica, sodium salts, magnesium minerals, or small quantities of phosphoric acid.

Jan 1, 1960

By Robert Torbin

The objectives of the Continuous Shaft Lining (CSL) System are to reduce the costs, safety hazards, and time currently required in lining mine shafts with concrete. The CSL will line machine bored shafts downward from the shaft collar on a continuous basis using an inverted, pressurized slipforming technique. The technique for slip-forming downwards has been demonstrated and refined under this program. The approach taken involved laboratory scale testing of key features of the CSL concept. These feature tests included concrete distribution, concrete sealing, concrete slipforming and development of a reliable concrete mix. Based on these results, a full scale above-ground test facility and CSL were designed and fabricated. The objectives of these tests were to demonstrate the viability of the basic concept; to establish operating limits; and to provide input data and information for the design of a second generation shaft lining system. The results of the program have led to a CSL design and operational philosophy which will need to be tested in an underground environment before industry will accept the technology. However, the next generation CSL promises to meet all the original program technical objectives.

Jan 1, 1983