Search Documents

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in develop¬ment of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By Richard C. Wang

The U.S. Bureau of Mines established a wire rope research laboratory to examine the factors that affect the safety and the useful life of wire rope. In the most recent work, two 32-mm 6x27H flattened strand ropes were degraded on a bending fatigue machine. The two tests were run at constant loads of 285 and 347 kN or safety factors of 2.5 and 2. Nondestructive and tensile strength tests were performed on samples of the ropes to determine the relationship between rope deterioration and rope breaking strength. Neither the area loss nor the number of broken wires measured from nondestructive tests could be used as clear indicators of the loss of strength. However, it was found from the tensile tests for both rope specimens that the strength loss was associated with the reduction of breaking strain. This suggests that measuring the strain of many short sections of a rope in the elastic region may locate the high stress sections and thus delermine the condition of the rope.

Jan 1, 2010

By Robert J. Timko

In early June 1986, an underground fire of unknown origin erupted in one of several entries of a coal mine located in southwestern Colorado. For a time, mine personnel aggressively fought the fire. However, control of the fire was later lost. To prevent further damage and reduce the possibility of an explosion, all portals and shafts to the mine were sealed. The mine operator requested the U.S. Bureau of Mines' assistance in obtaining and analyzing mine fire gases taken from sampling ports placed through the mine seals, as well as down boreholes drilled after the fire. This report recounts activities within the first 2 years of the mine being sealed. It includes a description of gases analyzed and mine atmosphere status equations generated from the analyzed gases. The gases were analyzed by chromatography and included standard atmospheric gases as well as higher hydrocarbons that are found in postfire atmospheres. Nine equations were used to evaluate what was occurring within the sealed mine. Following a description of the rationale behind each equation, the 2-year trend is briefly analyzed.

Jan 1, 2010

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By Eugene Fry

The Huber-Rydalch manganese property is in the Erickson mining district of Tooele County, Utah. The district covers the southern part of Simpson Mountains, a block rising abruptly above the surrounding desert floor (fig. 1). The Ruber-Rydalch deposits and other deposits in the Simpson Mountains manganese area were examined by Bureau of Mines engineers during 1940 and 1942 under the strategic minerals program. J. T. Pardee visited the district briefly in 1918. A. E. Granger and A. F. Shride, of the Federal Geological Survey, mapped the geology of the area in 1942 and 1943. The manganese deposits occur as veinlike masses in brecciated fault zones that traverse Cambrian and pre-Cambrian quartzite, quartzite conglomerate, and phyllite. The deposits now exposed near the surface represent the oxidized portions of primary mineralization originally containing rhodochrosite and rhodonite associated with quartz and calcite and small quantities of pyrite, galena, sphalerite, and chalcopyrite. The oxide ore is composed of manganite, pyrolusite, psilomelans, and wad in a gangue of quartz, calcite, and brecciated quartzite.

Jan 1, 1949

By B. E. Blair

The physical properties and related geological and petrographic data for 81 rock types obtained from operating mines or selected test sites are presented in this report. Most of these rock data were obtained to supplement structural studies in underground mines; however, the data may be equally applicable to other problems where the physical properties of rock are an important factor. Stress-strain curves are presented, where available, and free medium velocities from laboratory and field measurements are compared for several rock types. Rock-type, geographical, and geo-logical indexes are included for reference relative to physical property data in this and previously published Bureau of Mines physical property reports. INTRODUCTION This report presents the physical properties of 81 rock types from 16 different projects (sections 53-68). Three previous physical property reports2 3 4/ (herein after referred to as parts I, II, and III) presented data on 244 rock types from 52 project areas. (Part I included sections 1-25, part II sections 26-36, and part III sections 37-52).

Jan 1, 1956

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

By M. M. Gilkey

This report describes the effects of water shortage on Arizona's mineral industries. The information presented was obtained in interviews with company representatives. Operations covered included all State metal mines using substantial quantities of water and all concentrators and smelters. Also included in the survey were 8 operations in the nonmetallic group; 22 in the plating, metal-fabricating, and metal-forming categories; 1 public-utility power company; and 6 water companies. The extent of the water shortage in Arizona is reflected in mineral- industry water-use practices, in the high cost and low quality of water used at many operations, and in the stringency of State control of well drilling and pumping. Many mineral-industry operations are among those users most seriously affected by the uneven water supply.

Jan 1, 1963

By M. M. Gilkey

This report describes the effects of water shortage on Arizona's mineral industries. The information presented was obtained in interviews with company representatives. Operations covered included all State metal mines using substantial quantities of water and all concentrators and smelters. Also included in the survey were 8 operations in the nonmetallic group; 22 in the plating, metal-fabricating, and metal-forming categories; 1 public-utility power company; and 6 water companies. The extent of the water shortage in Arizona is reflected in mineral- industry water-use practices, in the high cost and low quality of water used at many operations, and in the stringency of State control of well drilling and pumping. Many mineral-industry operations are among those users most seriously affected by the uneven water supply.

Jan 1, 1963

By Lawrence G. Houk

Monazite sand is the only commercial source of cerium, other rare-earth metals and thorium. Although used in rather small quantities, it is essential to many industries. The United Unites is entirely dependent upon British India and Brazil for its supplies. Monazite sand or sand imported under the tariff classification for monazite was shipped to the United States in greater quantities, in 1940 than ever before. About 75 percent of our imports was from British India and most of the remainder from Brazil. If need be, Brazilian production can be expanded to supply all of our essential requirements, and the theater of war expands in the Pacific Brazil may supersede India as the principal source. PHYSICAL PROPERTIES The mineral monazite is generally honey yellow or may vary from greenish yellow to clove brown. The grains are small and resinous in luster, and range from subtranslucent to opaque. The specific gravity varies

Jan 1, 1943

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution3 by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1930, however, was unusually dry and represents what may be termed "extreme" low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscahonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.4

Jan 1, 1931

By John H. Soule

Appreciable quantities of sine and lead orus have been produced from the West. Pinos Altos district of Grant County, N. sex. This area was visited many times by engineers of the Bureau of ines. D. H. Johnson and 4. R. Storms visited the district in haren 1943 in connection with an acrenu road to toe wines. M. H. Storma again visited the area in July 1943 in connection with a hetals Feserve Corporation loan on the Routen-Thomas

Apr 1, 1948

By John R. Benham

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 20,500 acre Black Butte RARE II area (No. 5102) in the Los Padres National Forest (fig. 1). The work by the Bureau of Mines indicates that the potential tor mineral resources in the area is low. Samples of outcrops and stream channels contained no economic minerals. A mercury deposit near a granodiorite-sedimentary rock contact occurs 2 mi northeast of the study area, but similar deposits have not been discovered within the area. Geothermal potential exists near Tassajara Hot Springs, but no thermal springs occur in the area; nor have oil, gas, or coal resources been found.

Jan 1, 1982

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By C. B. DUTTON, W. F. RITTMAN, E. W. Dean, M. S. HOWARD

NOMENCLATURE USED IN THIS REPORT. In this report the ending ene has been used throughout, except in the bibliography and in quotations from the writings of previous investigators, for all aromatic hydrocarbons, as, for instance, benzene, toluene, xylene. The ending ol, though largely used in technical description, is not correctly applicable to these hydrocarbons, and should be used to designate the impure mixtures of commerce, as distinguished from pure chemical compounds. PRESENT STATUS OF PETROLEUM-REFINING INDUSTRY. Although petroleum is widely distributed, being found in many parts of the world, and although information as to its occurrence and general characteristics seems to have existed from vcry early times, our knowledge of the chemical nature of this substance has been acquired largely within the past 40 years. Within this period a voluminous literature has accumulated, which records work as painstaking as has ever been undertaken in the whole field of chemistry, such as that of C. M. Warren, F. H. Storer, S. P. Sadtler, S. F. Peckham, and C. F. Mabery. Despite this fact, the commercial method of treating crude petroleum for the purpose of procuring marketable products is, in the main, essentially empirical. Much knowledge has been acquired as to methods of separating from crude petroleum such products as are desirable commercially, but little has been done to attain the maximum recovery of such products.

Jan 1, 1916

By Alfred E. Schwaneke

A new high-temperature soft soldering system has been developed by the Bureau of Mines for use on copper, copper alloys, and low-carbon steel; the method is applicable to automobile radiators and home appliances. The system uses a unique sacrificial metal coating method to promote spontaneous wetting and spreading of zinc and zinc alloy solder: on metallic substrates. The 10-5 to 10-6 cm thick, electroplated or sputtered, sacrificial nickel coating is absorbed by the molten filler alloy during soldering and produces a direct solder-substrate metallic bond. Preliminary measurements on butt joints with copper members give tensile strengths up to 22,000 psi at room temperature using 95 Zn-5 Al alloy as solder. Spontaneous wetting, spreading, and capillary penetration are extremely rapid and produce joints as easily as 50-50 tin-lead solders. Recrystallization or annealing of the wrought copper joint members is negligible at the soldering temperatures of 450° to 490° C and lower. A list of fluxes and solder alloys is included in the report.

Jan 1, 1970

By Roy F. Abernethy

This publication by the Federal Bureau of Mines contains the free-swelling indexes for 2,812 samples of coal received from January 26, 1948, to July 15, 1957, and the Hardgrove grindability indexes for 2,339 samples of coal received from June 23, 1947, to July 15, 1957. These data consist of the origin of the sample, bed name, and analysis. Summaries show the high, low, and average values for each bed. The free-swelling index is a relative measure of the caking properties of a coal when burned on a grate, and the Hardgrove grindability index is used to estimate the relative ease of grinding coals. Development and standardization of these test procedures were at a much later date than those for the more familiar tests, such as proximate and ultimate analyses and calorific value determinations. The newer tests are valuable in supplying supplemental information, particularly for assisting in evaluating coals used in certain types of combustion processes.4/ Data from such tests are important to designers of burning equipment, operating engineers, and purchasing agents. Data from these newer tests are scarce and scattered through a number of publications. Special projects were started to determine the free-swelling and grindability indexes, in addition to the regular analyses on the tipple samples collected by Bureau engineers. Since the start of these special projects, all the coal fields of commercial importance have been adequately covered in the sampling program.

Jan 1, 1961

By John H. Johnson

White Pine Mine section designated for exhaust emissions studies. The MTU Mine Air Monitoring Laboratory was used to gather temperature and C02 concentration data at 10 locations. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in stratification in dead end headings. Diesel mine-vehicle tailpipe emissions were monitored in the laboratory by a portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. Diesel pollutant concentration data from the Orchard Valley Mine were analyzed and compared with data collected earlier in the White Pine and Brushy Creek mines. Lognormal frequency distributions and CO2-based concentration ratios and correlations were calculated. In the three mines compared, pollutant concentrations were distributed similarly, and concentrations appear to be controlled to present standards.

Jan 1, 1979

By William W. Adams

A new record in accident prevention was made by the metal-mining a industry of the United States in 1938, as signalized by a lower fatality rate than in any previous year. The rate was less than half as high as in 1911, the earliest year for which figures are available. A good safety record was also established in the prevention of nonfatal injuries, as the injury rate was lower than in any other years except 1931 to 1935, a 5-year period notable for its unusually low injury rates. Employment was more limited in 1938 than in 1937, both in number of men employed and total number of man-hours worked. The number of workdays per man also was smaller than in 1937. Operating companies reported that 7,233 mines were active in 1938 or some part of the year and that the total number of men employed was 103,027. This figure represents the summation of the average number of men employed as reported by the companies, the average for each mine being that for the period during which the mine was active. The number of employees at all mines in 1938 was 15,402 less than in 1937. Reports covering all mines indicated a total of 188 million man-hours worked during the year, or 21 percent less than the nearly 240 million man-hours worked in 1937. In the performance of this work accidents occurred that resulted in the death of 156 employees and the injury of 1.2,722, each injured employee being disabled for more than the remainder of the clay on which he was hurt.. The fatality rate for 1938 was 0.83 per million man-hours worked, which was 9 percent more favorable than the rate of 0.91 for 1937. Nonfatal injuries occurred at the rate of 67.61 per million man-hours worked, an improvement of 10 percent compared with the injury rate of 75.37 for 1937.

Jan 1, 1941

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952