Search Documents

By E. H. Burroughs

This bulletin is the fourth in the series of petroleum bibliographies being published by the Bureau of Mines, the three preceding, Bulletins 149, 165, and 180, being compilations for the years 1915, 1916, and 1917, respectively. In this bulletin the same general plan has been followed in arranging the references, but a few changes and additions have been made in the classification, the more important changes being in the classes "Geology and Origin" and "Refining and Refineries." Dl1'ring the year German periodicals were not available, and, as in the bibliography for 1917, references to articles in foreign journals that were not available have been taken' from other sources and credit given to those sources.

Jan 1, 1921

By G. B. Sonneman

This final report summarizes the work done by The Bendix Corporation, Environmental Science Division, under contract to the Bureau of Mines to design, develop and test two improved systems for remote sampling the air at the working face of a coal mine in conjunction with approved portable methane detectors and machine-mounted methane monitors respectively. The work was started in May 1973 with preliminary design studies and was completed in May 1975. Five portable and two machine-mounted sampling systems were delivered. Contract "add-on" requirements for (1) modification of the machine-mounted system to accommodate a flame safety lamp and (2) a study of sensor response time improvement for the machine-mounted system were also completed.

Jan 1, 1975

By Lloyd Williams

1. The investigation shows that the Pewee, Big Mary, and Windrock are the most important beds in Anderson County. About 73 percent of the known recoverable reserves of coal in the county are in these beds, and from them comes 94 percent of the production. The remaining reserves tabulated in this report are in the Joyner, Jellico, Coal Creek, and Poplar Creek beds, and 6 percent of the county production comes from these beds. No production is being reported at present from the Jellico bed, although it was mined years ago. 2. Known measured and indicated reserves in all beds, bared on a minimum thickness of 1/4 inches and on 1,800 short tons put acre-foot of coal in place, are estimated to be 170 million torts as of January 1, 1953 Of this total, 155 million tons is in beds 2S inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to they total estimated reserves.

Jan 1, 1955

By M. D. Aldridge

This document reports the results of a two-year research effort aimed at improving communication systems used in coal mines. This work was conducted under a program whose original goal not only involved the development of practical and effective electronic systems for operational communications, but also for monitoring, at a central location, remote instruments at key positions in a mine. About half way through the originally proposed three year effort, the program was redirected to phase out the communication effort at the end of two years and to concentrate the program" resources on the investigation of new monitoring system concepts developed by this research. Thus, the work reported here is incomplete relative to the originally pro- posed program. However, the work was carried to the point of providing sufficient evidence to aid in the comparison of certain new communication concepts. For the concepts chosen for this study, the work was stopped short of hardware development and field testing, Several reports in the form of Master's theses and a Doctoral Dissertation have resulted from this research. They each report in considerable detail the results of several individual" contributions to this program. In preparing this report, an attempt has been made to provide a complete description of the significant results but with- out burdening the reader with the minute details. These more detailed reports are referenced heavily for the convenience of those interested. PRESENT COMMUNICATION METHODS Two types of communication systems are presently used In coal mines. They are: 1, Various forms of telephone systems, and 2. Carrier current radio systems using the trolley line as the interconnection circuit. Carrier current radio is used almost exclusively for control of rail trafflc by the dispatcher. Almost all other communication uses the telephone system, Telephone lines generally extend to areas where trolley lines are not present such as the outside offices and warehouse. Therefore the telephone system provides the primary means of voice communication. Telephones - Telephone systems employed in American coal mines fall into three categories. 1. Paging type telephone systems - these systems have individual stations which use battery powered transistor audio amplifiers to boost signal levels for normal communication. When in the page mode,

By Wiliam L. Crentz

The importance of Somerset County, Pa., as a coal producer is due in large measure to the presence reserves of low-volatile bituminous coals. Although many coal beds of minable thickness are present, the important reserves are to be found in those beds underlying the Pittsburgh bed. The Kittenning beds and Freeport beds, which are responsible for the bulk of the present coal production in Somerset County and contain the largest reserves to meet future coal requirements, are usually thin and entirely free from impurities. The Pittsburgh bed, which has been such an important coal deposit in the coal areas immediately west and south of Somerset County, is of secondary importance in this county. Although generally rather friable, Somerset County coals have enjoyed wide receptability as excellent coals and to some extent have been utilized in the metallurgical market.

Jan 1, 1951

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By H. P. Greenwald, H. C. Howarth

There was reported in Bureau of Mines Technical Paper 5754/ a series of tests to determine the compressibility and bearing strength of specimens prepared from blocks of potash salt obtained from a mine near Carlsbad , N. Mex . The events leading up to the investigation were sketched in a foreword by George S. Rice , then chief mining engineer of the Bureau ( retired September 30 , 1937 ) ; this foreword also gives a discussion of the possibility of increasing the ultimate total recovery of the potash salt by " second mining" of pillars or by use of a longwall system . In June 1936 , Rice and the senior author visited Carlsbad with H. I. Smith , chief of the mining division of the Geological Survey , to observe mining then in progress and to discuss with the management of one of the mines records of convergence of roof and floor which they were obtaining . It developed that serious thought was being given to the possibility of roof failure resulting from shear at the faces of pillars . There was envisioned the danger of such cracks extending upward to water - bearing strata . Obviously , the simple compression tests of the potash salt then being made would throw no light on this question , and tests of assemblies of potash and roof salts would have to be made . In this connection it is to be remembered that in the mine no sharp division exists between the potash salt being recovered and the nearly pure halite which forms the roof . The interlocked crystalline structure is continuous , and there is merely a very rapid decrease in the proportion of sylvite in a short distance vertically . Figure 2 of Technical Paper 575 shows that two samples near the top of the salt being mined contained , respectively , 51 and 65 percent potassium chloride . Contrasted with this is an analysis of the roof salt given on page 24 of that publication , which showed only 3.6 percent potassium chloride . As the data given in Technical Paper 575 show , the roof salt is much less plastic than the potash salt . The immediate roof may then be thought of as a more rigid stratum of indefinite extent resting on and continuous with yielding supports and loaded uniformly at the rate of 900 to 950 pounds per square inch . Just what thickness of the salt should be considered as immediate roof is uncertain .

Feb 1, 1938

By Robert A. Westin

Polychlorinated Biphenyls (PCBs) have been widely used as fire resistant dielectri coolants in electrical equipment used in mining applications, including transformers capacitors, electric motors, and electromagnets. In addition, PCBs have been used in hydraulic fluids and heat transfer fluids, and are present in many oil filled transformers. The Environmental Protection Agency recently banned the manufacture of PCBs and equipment using PCBs, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggest ways to decrease the risks resulting from continued use of PCB equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.

Jan 1, 1979

By A. C. Fieldner, W. A. Selvig

Information concerning the fusibility of coal ash has become of considerable value to the consumer of coal, mainly in connection with the troublesome formation of clinker resulting from the melting of the ash constituents of the burning coal. The growing interest in such data has led the Bureau of Mines to make a general survey of the "fusing" or "softening" temperatures of the ash from coals of the United States. It is hoped that this information when used together with the large number of coal analyses published 1 by the bureau will assist the consumer of coal in comparing different coals, and in selecting the coal best adapted for his purpose.

Jan 1, 1922

By Jeffrey Y. Foley

Chromite deposits along the Border Ranges Fault in southern Alaska were investigated by the Bureau of Mines. This report, part 1 of a two- part series, describes the deposits. Part 2 describes the mineralogy and the results of metallurgical tests. Fieldwork began in 1981 and continued through 1983. Ninety-four subeconomic podifom chromite deposits in eight mafic-ultramafic complexes were investigated. Previously unreported chromite deposits at Red Mountain on Kenai Peninsula, on Kodiak Island, and near Tonsina are described. Deposits range in size from less than a thousand tons to over 1.25 million tons of contained chromic oxide (Cr203). Grades range from about 5 to 10 pct chromite. Excluding all deposits more than 10 miles from tidewater or existing roads and all deposits containing only chemical- or refractory-grade chromite, about 2,200,000 tons of Cr203 are contained in 41 hard-rock deposits. A placer deposit contains an additional 556,000 tons. These 42 deposits constitute a subeconomic indicated and inferred reserve sufficient to meet the Nation's chromite demands for about 4 yr, or the metallurgical industry's demands for over 5 yr, at 1981 consumption rates.

Jan 1, 1985

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1966-67. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By E. P. Youngman

In the absence of any subsequent enactment of mining legislation, the Turkish mining law in effect in 1914, when Iraq became a British mandate, is still operative. The Constitution, or Organic Law, of Iraq, adopted by the Constituent Assembly on July 10, 1924, in articles 113 and 114, provides that:3 Ottoman en laws date and thao remained and lave pub- lished on or after that date and which have remained in force in Iraq u to the time of the publication of this law shall remain in force in Iraq' so far as circumstances permit, subject to any modi- fication or repeal in conformity with the proclamations, regula- tions, and laws referred to in the following article, and until they are altered or repealed by the legislative power or the High Court issues a decision rendering them null and void in accordance with the provisions of article 86. (Art. 113.) All proclamations, regulations, and laws by the Commander-in- Chief of His Britannic Majesty's Forces in Iraq, the Civil Commis- sioner, and the High Commissioner, and those issued by the Govern- ment of His Majesty King. Faisal, during the period between Novem- ber 5, 1914, and the date of the coming into force of this Consti- tution, shall be considered to be valid as from the date on which they came into force... (Art. 114.) 4 According to a German authority, it is the Turkish law of March 26, 1906, that, with a few modifications, is still in force. This law (similar to the French law of 1810) is discussed in a separate section of this paper.

Jan 1, 1933

By Charles E. Glass

The purpose of this report is to demonstrate the flexibility of rte sensing techniques for providing data with which to implement mined-lands reclamation in an efficient and cost-effective manner. An operational program is presented for using satellite remote sensing data, collateral data, and automated image analysis to provide: 1) an inventory of coal and copper mines and mine waste in Arizona, 2) techniques for periodic monitoring of mining areas using multitemporal classification and image prediction techniques, and 3) delineation of high priority areas for future reclamation and current land-use planning of Arizona mining areas based on environmental hazards indices computed using classified scenes and collateral data.

Jan 1, 1980

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation. and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice. making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being headed by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems best suited for the work in hand. The following, projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration or a linear relation between surface and coercive force in magnetic minerals and Its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1. 1934, to June 30, 1935.

Jan 1, 1936

By R. S. Dean

The function of the Metallurgical Division is to conduct investigations relating to the treatment of mineral products from the state in which they are mined to the refined metal or other unfabricated product. These investigations include scientific and practical studies of ore dressing, covering the crushing and grinding of ores, separation by gravity, flotation, and magnetic methods; the hydrometallurgical treatment of ores, including cyanidation and amalgamation of the precious metals; the smelting and refining of copper, lead, and zinc, as well as the rare metals; and steel-melting practices from the raw ore to the finished steel. The object of this work is to conserve natural resources and eliminate waste by furnishing information on current methods of metallurgical practice, making fundamental studies of metallurgical processes, and developing new processes to the point of demonstrating their practicability. The Division is made up of sections devoted to the several phases of this work, each section being beaded by an investigator capable of supervising his particular work. The work is carried on at the experiment stations and field offices or in the field, whichever seems test suited for the work in hand. The following projects should be mentioned as particularly outstanding among those consummated successfully during the year: 1. Application of the type of chemicals known in the textile industry as wetting-out agents to flotation and agglomeration of ores, particulary soluble salts such as sodium and potassium chloride which must be treated in saturated brine. 2. Demonstration of a linear relation between surface and coercive force in magnetic minerals and its application to magnetic separation and to the determination of grinding efficiencies and other metallurgical data which require surface determination at very fine sizes. 3. Pilot-plant demonstration of the practicability of the reduction of iron ore by natural gas and conversion of this direct iron into steel by direct melting and by forging and rolling before melting. The structure and properties of the iron so produced were studied in detail. This report covers the fiscal year July 1, 1934, to June 30, 193b.

Jan 1, 1936

By Ernest A. Curth

Statistics For 1956-66 show that mine transportation accidents accounted for 19 percent of fatalities in bituminous coal mines, second only to roof deficiencies as a cause of death. Productivity per man-shift increased from 10.2 tons in 1956 to 18.4 tons in 1966, but the fatalities per million man- hours of exposure also increased from 0.19 to 0.21 during that same period, indicating that transportation hazards still persist. Consequently, the Bureau of Mines reviewed the transportation fatalities that occurred in bituminous coal mines during 1956-66. The data were processed by computer to find what constitute hazardous conditions and unsafe actions as well as to correlate occupation and age of victims, transportation type, and mine production. Environmental factors and equipment defects which create hazards, as well as unsafe actions of personnel, were determined for each type of mine transportation: Track haulage, mobile nonrail haulage, conveyors, hoists, automotive operations, and front -end loaders, and for transfer stations (loading points, slope and shaft bottoms, surface transfers) and railroad yards. Man-trip accidents, a group with a catastrophe potential, also were analyzed. The basic design and operational features of each transportation type were outlined and procedures considered safe in the light of accident experience were suggested. Findings show that unsafe actions of personnel and hazards created by environmental deficiencies or equipment malfunctions contribute equally in causing transportation accidents. Accordingly efforts should be directed toward improving working conditions, equipment maintenance, and education and training of employees. The trend is toward using safer modes of transportation, notably conveyors. More attention should be given to track haulage operation, railroad yards, and nondestructive field testing of materials.

Jan 1, 1971

By J. E. Rourke, O&apos

This report incorporates a review of available dewatering technology and an evaluation of its relevance to surface coal mines in the Interior Province of the United States. Guidelines for the selection, design and construction of dewatering systems are included. On the basis of documented experience, candidate dewatering systems were selected and evaluated with respect to their anticipated impact on the environment and mine operations. Included in the discussion is a summary of laws and regulations which can impact on dewatering operations. Following this discussion, geologic and hydrogeologic conditions within the Interior Province are described and potential dewatering problems at surface coal mines are identified. Model mines are developed which exhibit the most difficult dewatering problems identified, and it is demonstrated how available technology can be utilized to deal with these problems. Dewatering of coarse-grained, high permeability terrace deposits might be economically feasible today. Low permeability, saturated glacial tills or lake deposits appear to be significantly outside present economic feasibility for dewatering.

Jan 1, 1979

By Robert W. Thomas

This paper describing the mining practices at the Ray mines at Ray, Arizona, is one of a series being prepared by the Bureau of Mines on mining practices, method and costs in the various mining districts of the United States. At the present time (1929) all mineral Production of the Ray district comes from the Ray Mines of the Nevada Consolidated Copper Co. The ore body is being worked from two shafts, designated as No. 1 and No. 2. An undercut block-caving method of mining is used, variations of which are employed to fit different conditions. The present method has been developed by making improvements as experience was gained or when conditions changed. Refinements in practice are continually being made. The Ray mine was the first in the Southwest to use a caving system of mining on a large scale.

Jan 1, 1929