Search Documents

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By Francis X. Cannaday

Equipment and techniques were developed with Bureau of Mines facilities for measurement in the laboratory of sonic shear wave velocity in variously shaped rock specimens in a wide range of sizes. A variety of rock types was tested. The shear wave front is produced by electronically excited, piezo-electric ceramic) disk-shaped transducers. Transmitter and receiver are interchangeable. Special equipment components were Bureau produced; other components were commercially available. The equipment permits quick measurement of shear wave velocity on variously shaped specimens with a minimum of specimen preparation. The technique, under favorable conditions, allows for determination of the moment of arrival of the shear wave when it is superimposed on a weak longitudinal wave.

Jan 1, 1968

By E. H. Burroughs, M. J. Gavin

The references in the following compilation are selected chiefly from the literature of the years 1915-1920 , though a few of the more valuable standard works published before that period have necessarily been included . References to many articles have been omitted purposely , because the material covered by them is duplicated in publications included in the bibliography . It is manifestly impossible for the Bureau of Mines either to recommend or adversely criticize the statements of the various writers , particularly as to cost and profit estimates in articles referring to American shales , but it is hoped that the investigator will use caution in considering such statements , as it is well known that much of the literature on this subject has been published for promotion purposes and is therefore over- enthusiastic . Bearing this fact in mind , the reader should be able to judge for himself the reliability or usefulness of these articles .

Sep 1, 1921

By H. R. Appell

The Bureau of Mines is experimentally converting cellulose, the chief constituent of organic solid waste, to a low-sulfur oil, All types of cellulosic wastes, including urban refuse, agricultural wastes, sewage sludge, wood, lignin, and bovine manure, have been converted to oil by reaction with carbon monoxide and water at temperatures of 350° to 400° C and pressures near 4,000 psig, and in the presence of various catalysts and solvents, Cellulose conversions of 90 percent and better (corresponding to oil yields of 40 to 50 percent) have been obtained. A continuous reactor for use at maximum conditions up to 500° C and 5,000 psig has been operated successfully, Using sucrose as a feedstock, operation in this system has permitted a simplified and preliminary chemical study of the conversion process. Oil yields of over 30 percent have been obtained with this unit.

Jan 1, 1971

By J. R. Hamke

THE WILLISTON basin is the largest known sedimentary basin on the North. American continent. Two-thirds of this large basin lies within the United States in Montana, North Dakota, and South Dakota. Less than 10 years after the first commercial oil discovery in North Dakota in 1951, the petroleum became one of the largest industries in the three-state area. Crude petroleum is now the most valuable mineral resource in the area. In 1960, the basin produced 39 million barrels of worth $100 million at the wellhead. Most of the 137 oil pools covered to date are in Paleozoic carbonates at depths ranging from 3,000 to 13,000 feet. The major producing fields, centered on the Cedar Creek anticline in Montana and the Nesson anticline in North Dakota, produce from depths below 6,000 feet. This report presents descriptions of all phases of the Williston basin petroleum industry, including leasing, exploration, geology, drilling, production, transportation, and refining. Engineering, physical, and production data, maps, and crude petroleum analyses for 137 separate oil pools are included.

Jan 1, 1966

By R. S. Dean

[In E;encralt the I~8:al:ul',~,C,-J. Div:'sion conducts in\'8stigations relat-ing to the treatment of OrGR o.nd L!\3tallurl..'"lcal prod tctR froJ] t~e condi tion in :hich they are Itinod to t!1e refi!l(,u r.etal, . ' th 'the ob,icct of conserving natmal' resources .e..nd 81:mir..3.tin~ wacte by furn.i:::hir..g :nforInf'_tiou on current methods of metal11:.rgical practice, Tfu'..:.kir..g fund T!l;ntal .;;.otudie'" of metal-lurgical processe~, and de~eloping ~e~ proc6sses O~Q lloys to the point of dewonctrati:r:g the:'..r practicab'lity or va.lue}

Jan 1, 1941

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By Warren W. Krech

Rock property data is needed over a wide range of parameters for the optimum execution of rapid excavation research. Eight rock types were chosen by the Bureau of Mines for a standard rock suite for such research. Large rock blocks were quarried and the standard physical and mechanical properties measured and documented. The eight rock types that comprise the rock suite are Barre Granite, Berea Sandstone, Dresser basalt, Holston Limestone, Salem Lime-stone, Sioux Quartzite, St. Cloud Gray Granodiorite, and Westerly Granite. Geologic, petrographic, physical-property, and mechanical-property test data are reported for each rock type. The information is the first step in the building of a comprehensive property listing for the eight rock types. A limited number of rock cubes are available from the Bureau of Mines Twin Cities Mining Research Center for use by researchers to broaden the information available on the suite.

Jan 1, 1974

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography. The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on an' type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the round outside seemed to shake the building as a single loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on any type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the ground outside seemed to shake the building as a single, loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By K. E. Tame

Pollution from radioactive nuclides, principally Ra226, in liquid waste from uranium mills can be minimized by reusing the waste solution within the mill. Such reuse of waste solution in the Vitro Chemical Co.-type process was investigated in the laboratory. Vitro employs an acid leaching process for dissolution of the uranium, countercurrent decantation for liquid-solid separation and washing, and amine solvent extraction for recovery of the uranium from solution. The simulated reuse of barren raffinate in the mill circuit was carried through two separate laboratory campaigns of 29 and 31 cycles. Conventional chloride stripping of the amine was employed in the first campaign, whereas nitrate stripping was used in the second campaign. Dissolution of uranium from the are in the acid leaching circuit averaged 96 percent. Washing efficiencies of 98 to 99 percent were attained by using 4 volume tons of combined raffinate and makeup water per ton of ore. Uranium recovery from the pregnant solution using a 5-percent solution of amine LA-1 in kerosine ranged from 99.3 to 99.9 percent.

Jan 1, 1962

By Alan Mayton, Bertrand Valero, Farid Amirouche

Handling of heavy vehicles such as tractors, trucks and buses require a large roll stiffness which causes large high accelerations at the seat level during impacts. To provide comfort and minimize the energy transfer from the chassis and the seat a pneumatic active seat suspension is proposed. An active seat suspension design and control algorithm under development at the University of Illinois at Chicago, UIC, is being developed and tested. Preliminary results are presented in this paper. The design of a passive suspension typically consists of optimizing the value of two parameters: the stiffness and the damping of the suspension. The general dynamic performance of the suspension is limited to the conditions under which these parameters were obtained. A change in the input conditions might lead to poor suspension and an amplification of the vibration transmitted to the body. The focus of this paper is a robust, semi-active suspension system with a variable controlled damping and using the body response an index measure to minimize the acceleration at the interface of the seat and operator. A summary of existing suspensions, such as MR and ER fluids, and spring loaded and dual valve shock absorbent will be discussed to highlight the need of a semi-active pneumatic suspension system design. Methods A model of the proposed suspension was developed in MATLB (Simulink) and different control strategies for the valve position in relation to the cylinder pressure tested. The effects of stiffening and softening resulting from pressure changes in the cylinder were examined. The vertical accelerations of the seat was computed for different control strategies and configurations of the suspension and compared to the response of a passive seat suspension. A lump -mass model was created to represent the human body including the head, the upper, middle and lower torso as well as the legs. The connective forces between body segments were modeled through modal analysis techniques from previous experiments at the Vehicle Technology Laboratory. ISO standards and absorbed power were used to evaluate the different configuration of the seat suspension system in relation to the dynamic response of the operator. Results Initial results of the semi-active suspension system show a significant reduction in the RMS value of the acceleration of the seat. A reduction of the total absorbed power by the operator is expected to provide an insight into the control strategies adapted in the active suspension.

Jan 6, 2006