Search Documents

By Alan A. Campoli

The U.S. Bureau of Mines evaluated two different conventionallongwall gate entry systems in the Southern Appalachian Basin, where mining and geologic conditions are conducive for coal pillar bumps. These gate entry systems were in a coal mine located in the Pocahontas No.3 Coalbed under approximately 2,000 ft of overburden and a massive quartzite sandstone member, and both employed a center abutment pillar flanked by yield pillars. The 8O-ft-square tailgate abutment pillars within the first study area began bumping 500 ft in advance of mining. This was accompanied by face bumps on the tailgate corner of the longwall face. The 120-by 180-ft tailgate abutment pillars within the second study area did not begin to bump until mining was approximately 100 ft past. Coalbed stress change and abutment pillar dilation data demonstrated that a 15-ft-wide perimeter of yielded coal surrounded a highly stressed core in both sizes of abutment pillars. The 62 pet more core area per foot of gate entry in the larger abutment pillars prevented excessive load transfer to the corner of the tailgate panel and eliminated the face bumps experienced with the original gate entry design.

Jan 1, 1990

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By R. Karl Zipf, Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non-fatal injuries to human workers. A commonly used technique is to devise an “incident prevention plan”, which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident – in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of “events of interest”. This paper introduces a novel technique – “Taxonomic Analysis”, which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984-1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By M. W. Von Bernewitz

Fay's glossary3/ of terms contains the following definition of "black sand": Heavy grains of various minerals which have a dark color and. are usually found accompanying gold in alluvial deposits, for example, magnetite, chromite, ilmenite, cassiterite, tourmaline, and others. The Bureau of Mines is issuing this report in answer to the many inquiries from individuals and firms as to how they may treat or sell the heavy black sands that accumulate in the sluice boxes of beach and river placering and to warn such individuals and firms against becoming too enthusiastic over the chances of striking it rich. For a half century or longer much money, energy, and time have been wasted in devising, building, and trying numerous machines to recover gold and platinum, also gem stones, from sand that generally has not been worth the effort. Volumes have been written on the subject, and thousands of letters of inquiry have been received by agencies of the State and Federal Governments. The demand for information has been so great that all of the Bureau's publications dealing wholly or partly with black sands are out of print. They are listed at the end of this report.

Jan 1, 1938

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

By Leonard Obert

The ultimate object of this investigation is to develop a method for determining the pressure, in- situ, on rock mine pillars, arches, end other mire structures. The preliminary investigations of Bureau of Mines engineers, as well as those of other investigations4/ have shown that, the velocity of sound depends on the pressure if it is dependent to such an extent that a measurement of the velocity might be used as a means of determining the pressure, a sonic method of measuring the pressure on rock mine columns is possible. Briefly the method would require, first, laboratory determination of the variation of the velocity of sound with pressure in samples of rocks taken from mine pillars to establish a. velocity-pressure relationship for the type of rock and, next, measurements of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. Obviously the success of the method depends on the extent to which the velocity of sound varies with pressure in rock.

Jan 1, 1939

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

By Leonard Obert

The ultimate object of this investigation is to develop a method for determining the pressure, in situ, on rock mine pillars, arches, and other mire structures. The preliminary investigations of Bureau of Mines engineers, as well as those of other investigators,4/ have shown that the velocity of sound depends on the pressure if it is dependent to such an extent that a measurement of the velocity might be used as a means of determining the pressure, a sonic method of measuring the pressure on rock mine columns is possible. Briefly the method would require, first, laboratory determination of the variation of the velocity of sound with pressure in samples of rocks taken from mine pillars to establish a. velocity-pressure relationship for the type of rock and, next, measurements of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. Obviously the success of the method depends on the extent to which the velocity of sound varies with pressure in rock.

Jan 1, 1939

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By David C. Benson

This Bureau of Mines report is an update of IC 8725 and comprises tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities; the report covers the 26 States east of the Mississippi River. Of the total 535 projects for which information is provided, 429 concern coal mines and electric generating plants (including Energy Supply and Environmental Coordination Act (ESECA) coal conversion notices).

Jan 1, 1978

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By Gerrit V. R. Goodman

In This Chapter [Design and operation of machine-mounted scrubbers Dust control with scrubbers and blowing ventilation Dust control with scrubbers and exhaust ventilation Dust control with exhaust ventilation and no scrubber Dust control methods common to all continuous miner sections Dust control for roof bolters] This chapter explains how to control dust at continuous miner sections in coal mines where the main dust sources are continuous miners and roof bolters. In relation to dust, there are three categories of continuous miner faces depending on the type of ventilation and whether or not a machine-mounted dust scrubber is used. These are— 1. Mining machines with dust scrubbers used with blowing face ventilation 2. Mining machines with dust scrubbers used with exhaust face ventilation 3. Mining machines without scrubbers used with exhaust face ventilation The approach to dust control is somewhat different in all three of these. However, there are many dust control features (such as the need to provide adequate airflow) common to all continuous miner sections. For workers at roof bolter faces, there are two dust sources: 1. Dust from the continuous miner when it is upwind. 2. A malfunctioning dust collector on the bolter, which allows dust to escape DESIGN AND OPERATION OF MACHINE-MOUNTED SCRUBBERS [Almost all new continuous miners are equipped with scrubbers. When the dust is excessive, it is possible that the scrubber needs some maintenance.]

Jan 6, 2003

By H. H. Dewing

The Bureau of Mines constructed a process research unit (PRU) to demonstrate new technology for extracting zinc from sphalerite concentrates. Up to 9 kg/hr of sphalerite (ZnS) concentrate was reacted at ambient pressure in the PRU with 80 pct sulfuric acid at 160° to 180° C to produce zinc sulfate and elemental sulfur. The PRU consisted of a three-stage glass reactor system: a 4-liter premix stage in which feed was slurried with 78 to 82 pct H2S04, a 40-liter stirred reactor, and a ISO-liter settling stage in which high reaction conversions were effected and excess H2S04 for recycle was separated from insoluble ZnS04 and sulfur. Evolution of sulfur-containing gases was minimized by sub-surface addition of acid feed slurry to the stirred reactor and by exclusion of air from the reactor to prevent the oxidation of elemental sulfur. Conversion of zinc to zinc sulfate averaged over 99 pct at the optimum acid concentration of 80 pct. Total sulfur losses (primarily S02) were less than 2 pct of the sulfur in the sphalerite. Elemental sulfur remained in the insoluble portion of the settled reactor product after leaching with simulated spent zinc electrolyte containing sulfuric acid. The sulfur residue contained 75 to 89 pct sulfur. Neutral zinc sulfate, required for zinc electrowinning processes, was separated from the sulfuric acid leach solution by crystallization at -15° C as zinc sulfate heptahydrate (ZnS04?7H20). The crystallization operation simultaneously effected a partial concentration of the recycled electrolyte solution by removing water.

Jan 1, 1982

By Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular industry or commodity. 2. Recirculation is dependent on the processing requirements of a particular commodity, the manner in which the water is used, cooling and condensing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

Jan 1, 1966

By A. G. Galaitsis

This report summarizes the work performed under the USBM Contract No. J0245001. The purpose of this work was to expand and improve the scope and accuracy of the method developed under USBM Contract No. J0113056 for the prediction of the number of overexposed workers in the mining industry. A significant portion of the noise data were acquired during mine visits-that took place in the-course of this contract. These data were obtained with time-resolved dosimeters which among other things store a time history of the sampled noise for an eight hour work period. The remainder of the noise data have been obtained from MSHA files and from other BoM-sponsored projects. The report reviews the prediction model, discusses the model's assumptions and approximations, describes the function of the developed software, offers typical examples on the use of the software and includes plots of the newly acquired noise data records.

Jan 1, 1986