Search Documents

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By C. T. Baroch

CESIUM-137 ISOTOPE began to displace cobalt-60 III the treatment of cancer during 1956. Production and Consumption.-Consumption of cesium and rubidium was approximately the same as in 1955. Production, however, decreased, as several companies shipped from stocks produced in previous years. South Africa was the source of most cesium and rubidium minerals used in the United States in 1956. Cesium and rubidium metals and compounds were produced from ore by: DeRewal International Rare Metals Co., Philadelphia, Pa.; Fairmont Chemical Co., Inc., Newark, N. J.; Foote Mineral Co., Philadelphia, Pa.; and Rocky Mountain Research, Inc., Denver, Colo. Most sales were to domestic consumers, but small quantities were exported to Australia, England, Germany, and Sweden. New production facilities were under construction in. 1956 by San Antonio Chemicals to produce mixed potassium, rubidium, and cesium carbonates. A plant capable of separating and packaging 200,000 curies of cesium-137 annually was under construction at Oak Ridge National Laboratory.6

Jan 1, 1958

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

By Robert L. Virta

This U.S. Bureau of Mines paper discusses the structure of the talc industry, talc production, processing of talc ore, applications and demand for talc, and the outlook for the talc industry.

Jan 1, 1989

By Gerald T. Homce, James C. Cawley

Arc flash generally refers to the dangerous exposure to thermal energy released by an arcing fault on an electrical power system, and in recent years, arc flash hazards have become a prominent safety issue in many industries. This problem however, has not been effectively addressed in the mining industry. MSHA data for the period 1990 through 2001 attributes 836 injuries to “non-contact electric arc burns”, making it the most common cause of electrical injury in mining. This paper presents results from several elements of a recent NIOSH study of arc flash hazards in mining, and provides information and recommendations that can help reduce these injuries. Characteristics of past arc flash injuries in mining are first outlined, such as the electrical components and work activities involved (based on MSHA data). This is followed by a review of important concepts and terminology needed to understand this hazard. Next, methods for identifying, measuring, and managing arc flash hazards on a power system are covered, with emphasis on recommendations found in NFPA 70E, Standard for Electrical Safety in the Workplace. Finally, results are presented from a detailed arc flash hazard analysis performed on a sample mine electrical power system using IEEE 1584-2004a, focusing on components and locations presenting severe hazards as well as engineering solutions for reducing the risk to personnel. Index terms – electrical arcing, electrical burns, mining, arc flash hazard analysis

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By Thomas Novak, Jeffrey L. Kohler, Joseph Sottile, Steve J. Gnapragasam

Modern underground coal mines can be very large, having a total connected load in excess of l5 000 hp. These mines generally have many miles of high-power conveyor belts and 15 or more miles of high-voltage power cables at distribution voltages of 12.47, 13.2, 13.8, or 14.4 kV. The shielded cables used in mine power distribution systems have a significant level of capacitance, on the order of 110 pF/ft. This level of capacitance, in an extensive power distribution system at today's voltage levels, can cause significant charging currents during a ground fault. This paper addresses the potential detrimental effects of capacitance charging currents during line-to-ground faults in mine power distribution systems. A representative mine power system is modeled, and simulations with faults at various locations are conducted to evaluate the effects of this capacitance on the level of fault current and relay selectivity. This paper also includes results of capacitance measurements made on mine power feeder cables used to validate the simulation model.

[This Bureau of Mines report presents results of a survey of underground mining equipment and of two demonstration programs showing the feasibility If quieting; a load-haul-dump (LHD) machine and a personnel vehicle. Typical noise levels are presented for the major machine types used in underground mines, along with estimates of the noise overexposure of miners who operate or work near these machines. General principles of noise control are explained, and the application of these principles is illustrated in the description of modifications made to the LHD machine and the personnel vehicle. The noise control package installed On the persona of vehicle lowered its noise level by 14 dBA after 4 months of operation, and inspection of the LHD machine after 2 1/2 years of operation with the modifications showed its noise level 7 dBA lower than that of the unmodified machine. Noise dosimeter measurements indicated that both machines were in compliance with Federal noise regulations for a typical shift.]

Jan 1, 1980

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981

By W. K. Connor, O&apos

The U.S. Bureau of Mines investigated the Sheep Creek prospect in the north-central Alaska Range to evaluate the Pb, Zn, Ag, and Sn resources. The studies included field investigations, mineralogical characterization, and concentration tests. Mineralization at Sheep Creek consists of disseminated, banded, and massive pyrite, sphalerite, and galena. Tin occurs as grains of cassiterite (Sn02) in the quartz-mica matrix and within pyrite and sphalerite grains, and Ag occurs in solid solution within the galena. Three bulk surface samples and two sets of core samples were collected at the Sheep Creek prospect for this study. Gravity concentration yielded products with up to 30 pct Sn, and the best result was a product that recovered 52 pct of the Sn at a grade of 22 pct Sn. Bulk sulfide flotation yielded products that recovered up to 89 pct of the Zn, 73 pct of the Pb, and 75 pct of the Ag, but grades were relatively low; selective flotation would significantly increase the grades.

Jan 1, 1989

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By G. Ahnell

Throughout portions of four (4) heavily mined Appalachian states subdivided by the Mine Safety and Health Administration (MSHA) as: District 3 -Northern West Virginia and Maryland; District'" -Southern West Virginia; District 5 -Virginia; and District 6 -Eastern Kentucky, active coal mine waste embankments associated with mechanical and/or chemical coal processing facilities of various levels of coal preparation were inventoried. For each site plant specifications, disposal techniques, embankments' characteristics, and coal source data were accumulated. Mapping at 1: 24, 000 and 1: 250,000 scale and Disposal Site Characterization forms were developed to present the findings. Associated abandoned surface and underground openings near each site were also indicated as well as locational data for each site and the areas environmental conditions - temperature, precipitation and vegetation types. A state-of-the-art review of coal preparation, waste disposal, and alternative uses of coal waste is also included.

Jan 1, 1982

VOLUME II Volume II, in conjunction with Volume I, is a general guide to the selection of cost-effective methods of site data acquisition in all geologic environmental, and socio-political circumstances. The judgement of a generalist or trained specialist must be relied upon in the final analysis to design the optimum program for a specific site.

Jan 1, 1976

By R. H. Grau, S. B. Robertson, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. Large-opening mine ventilation is unique for the following reasons: (1) it is challenging to keep airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) large air volumes can be moved through the mines with little static pressure drop, and (3) stoppings to direct ventilation airflows are costly to construct and maintain. The research results suggest that by incorporating ventilation planning into the mine planning process, using propeller fans, developing new stopping materials and construction methods, and using long pillars to eliminate crosscuts where possible, the ventilation of large-opening mines can be significantly improved. The ventilation improvements created by incorporating these various techniques into the ventilation plan will help reduce the exposure of mine workers to airborne contaminants in underground large-opening mines.

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

By Charles C. Boley

Using bench-and pilot-scale coking facilities, the Bureau of Mines produced experimental coke from blends of char with Sunnyside coal (high-volatile A bituminous) from Carbon County, Utah. At bench scale, additions of char made from lignite improved resultant cokes when concentrations of up to 60 pct were used in the blends. At pilot scale (500-pound movable-wall oven), four chars made by entrained-bed carbonization techniques from the parent Sunnyside coal and from a North Dakota lignite were used in two-component blends with the Sunnsyide coal. Chars from Sunnyside coal had volatile matter contents of 5.8, 9.8, and 16.0 pct, moisture-free basis; the char from the lignite had 16.6 pct. In twenty-five 500-pound tests, improvement in coke quality was observed from all blends at char concentrations to 17.5 pct. The best coke, produced from a concentration of 12.5 to 15 pct of S.8-pct volatile char, exhibited physical properties approaching those of an industrial coke produced from Sunnyside coal blended with three higher rank blending coals. Studies were also made of the effects on coke quality of char source, of particle size, of comparative use of char and of a blending coal, and of prolonged coal storage.

Jan 1, 1973

By D. R. Flinn

A newly developed chemical conditioning technique, which greatly simplifies the preparation of plating baths for the electrodeposition of titanium diboride (TiB2) coatings, is described in this report. The new plating technique was used to prepare samples of titanium diboride (TiB2) coatings on three types of substrate materials. These samples were then evaluated in both low- and high-speed wear-test programs to determine the wear resistance, microhardness, and adhesion of the coatings. In general, it was found that the wear resistance of the coatings is independent of substrate. Scanning electron micrographs have shown that the coating wear surfaces are very smooth, suggesting slow and continuous removal of the coating during the wear test (that is, adhesive wear). Adhesion between the coating and all substrates was excellent. Microhardness results show that the TiB2 coating is harder than alumina, with a hardness value exceeding 5,000 kg/mm2 measured in one test. The results of the wear tests show that TiB2 coatings have relatively poor wear resistance compared with alumina in low-speed unlubricated sliding environments, but exhibit wear properties comparable with alumina in high-speed unlubricated sliding environments.

Jan 1, 1981