Search Documents

By Andrey Kozlov

The results of mineralogical?technological studies of PGM mineralization in zoned mafic?ultramafic complexes of the Ural?Alaskan type are given. The most important technological specificity of PGM mineralization hosted in dunites is its occurrence only in the form of free mineral species with predominance of Fe?Pt alloys (ferrous platinum, isoferroplatinum, and tetraferroplatinum). Technological properties, grain size, and good opening of PGM ore in grain size class +80 µm make it possible to concentrate ore using gravity methods with stadial comminution and between cycle separation of relatively large grains and nuggets into high-grade concentrates at the early stage of disintegration. Keywords: platiniferous dunites, PGM mineralization, mineralogical?technological studies and processibility research, recovery technology, gravity methods

Sep 1, 2012

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By Magnus Evertsson, Haijie Li, Erik Hulthen, Mats Lindqvist

"The static and dynamic models for autogenous (AG) and semi-autogenous (SAG) mills have been studied for decades. Though the effects of mixing soft and hard ores in a mill and their interactions are not widely investigated. To develop a general numerical model for AG/SAG mills, a dynamic model has been introduced, and its capability to simulate multi component ore breakage has been examined and compared with previous publications. The simulation results show that the dynamic model can cover a range of milling conditions and is able to simulate complex scenarios with soft and hard ores. The dynamic model discussed here could provide substantial potential for the controlling and optimization of the comminution circuits. INTRODUCTION In the last decades, efforts have been devoted to studying the comminution circuit due to their high energy consumption. The energy directly spent in minerals comminution was about 2% globally in the year 2000 (Maurice et al, 2003). As one important part of the comminution process, AG/SAG mills are widely used for primary grinding in minerals processing. AG/SAG mill models include static and dynamic models (Kojovic et al, 2012; Yu et al, 2014; Yu et al, 2017; Liu and Spencer, 2004; Salazar et al, 2009). Many static models have been well validated over the past decades, but they are all based on steady state assumptions. Even though plants experience a steady-state condition under certain circumstances, it can be inaccurate to simulate the system by static models under all circumstances (Asbjörnsson et al, 2013). The advantages of a dynamic model are apparent that it provides more information and insights both inside the mill and through interactions with other machines in terms of pebble crushers, conveyor belts, screens and so on. In many mines, the multi-component grinding is inevitable, and the ratio of hard and soft components in the mill strongly affects mills operation and performance. Bueno (Bueno et al, 2010; Bueno et al, 2013) studied the effects of blending hard and soft ores in AG/SAG mills and used them to update the JKSimMet toolkit which was a steady state plant simulation software. However, due to the complexity of the particle interactions such as multi-component breakage function, appearance function, in mill transportation, there has been no dynamic AG/SAG mill models developed yet for simulating multi-component."

Jan 1, 2018

By Cagri Emer

In conventional mechanical flotation cells, when the size of particles exceed a particular value, that is of the order of 100 µm for metal sulphides, the recovery of particles decline rapidly. It appears that the turbulence in the agitated vessel is sufficiently intense to rupture the forces of attraction between the particles and the bubbles, so the large particles are flung off the bubbles in the turbulent field. It has recently been suggested, that a fluidized bed would be a very favorable environment in which to contact bubbles and the particles. In a fluidized bed, particles are supported by rising flow of fluid, which separates them from each other and allows them to move freely while remaining close together. In this novel method, bubbles injected into the fluidized bed are able to rise through it, colliding with hydrophobic particles, transporting them to the top of the column where they can form a froth layer that overflows into a launder. The flow in a fluidized bed is generally slow and nonturbulent, and preliminary experiments have shown, that it is possible to collect mineral particles as large as 1 mm and coal particles as large as 5.5 mm. If the upper particle size limit can be extended, there could be significant reductions in the overall energy consumption in concentrators. Calculations show for example that if the top size for flotation could be increased from 100 µm to 400 µm, there would be a reduction in grinding energy of the order of 40%. It is therefore, important to study the mechanism of coarse particle capture in fluidized beds. In this work, the factors governing the capture rate of particles, particularly the particle and bubble size, the fluidization velocity and the superficial gas velocity have been investigated, and the results will be presented.

Sep 1, 2012

By Gabriel Barrios, Juan Pérez-Prim, Marcelo Tavares

"The application of High Pressure grinding Rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits generally supporting this trend are better energy efficiency, improved grinding capacity, less sensitivity to ore grindability variations and higher metal recovery in downstream processes such as heap leaching and flotation. The HPGR machine comprises a pair of counter-rotating rolls mounted in a sturdy frame. One roll is fixed in the frame, while the other is allowed to float on rails and is positioned using pneumohydraulic springs. The feed material is introduced in the gap between the rolls and is crushed by the mechanism of interparticle breakage. Comminution performance is largely determined by the pressure exerted on the bed of particles by the floating roll hydraulic system. The operating bed pressure depends on the hydraulic system start-up parameters and the loading response of the feed material. The work describes how the coupling of the multi-body dynamic simulation with Discrete Element Method in which particle breakage is described using the particle replacement method, can be effectively used to predict the performance of the HPGR. The model considers important variables as the HPGR rolls geometry and design, the hydraulic spring system start-up parameters and the material loading response, to describe operational key outputs as material throughput, operating gap and roller pressure distribution. The preliminary version of the model has been used to predict the effect of material properties on the operating gap and the load distribution on the surface of the rolls, demonstrating that it can describe qualitatively the HPGR operation, indicating that the model will be a power full tool for the simulation and selection of industrial HPGR units."

Jan 1, 2014

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014

By T. Sun, J. Kou, C. Sun, D. Gong

"HPGRs (high pressure grinding rollers) have demonstrated higher energy efficiency than conventional comminution equipment due to their application of particle-bed breakage mechanism. In the past decades, a large number of studies have been conducted to understand the characteristics of particle-bed breakage, however, few of them concerned the difference between single-particle and particle-bed breakage in compression comminution. This comparison is able to demonstrate possible advantages of particle-bed against single-particle in a breakage event due to the isolation of the effect of force loading mechanism. The present study investigated progeny fragment size and energy efficiency of these two breakage methods at variable energy inputs and particle sizes. The results show that at low energy inputs of around 0.25 kWh/t, the numbers of fines resulting from the two breakage methods are very similar. However, at higher energy inputs of around 1.0 or 2.0 kWh/t, particle-bed breakage generated significantly more fines. From the perspective of newly generated surface energy, particle-bed breakage is obviously more energy efficient than single-particle breakage at energy inputs between 1.0 and 2.0 kWh/t. It was also found that HPGRs demonstrate high energy utilization rate in generating new surface energy within their typical range of specific energy input. INTRODUCTION Rock comminution is an important and energy-intensive process in mining operations. Nowadays, decreasing head grade and mineral liberation size of ore deposits greatly increase the energy cost of comminution process. HPGRs have been successfully applied in the mining industry to improve the energy performance of comminution circuits. Typically, 10 to 30% of energy saving can be achieved due to the application of HPGR (Wang et al., 2013; Casteel, 2005; Günter et al., 1996)."

Jan 1, 2018

By Takaaki Wajima

The slag was attempted to be converted into the adsorbent for phosphate removal from aqueous solution using the alkali fusion method. The slag was mixed with NaOH powder (NaOH / Slag = 1.6), and then the mixture was heated at 600 ? for 6 h to prepare the precursor. The precursor was stirred at room temperature in distilled water to synthesize the adsorbent, and the removal ability of the obtained adsorbent for phosphate from aqueous solution was investigated. The products, including hydrocalumite and calcite, were synthesized, and the removal efficiencies of the adsorbent for F- and PO43- showed higher than those of raw BF slag, especially removal of PO43- are excellent (99 %), while the removal of Cl- , SO42-, NO3- and Br- was minor. The adsorbent could remove PO43- selectively in the co-existing solution of Cl-, NO3-, F-, SO42- and Br-.The equilibrium adsorption capacity of the adsorbent for PO43- was extrapolated using Langmuir and Freundlich models, and experimental data are found to fit Langmuir than Freundlich. The calculated maximum adsorption capacity of the adsorbent for PO43- is higher than other adsorbent reported previously. The high affinity of the adsorbent for PO43- in aqueous solution was caused by the formation of hydroxyapatite [Ca5(PO4)3(OH)] and brushite [CaHPO4?2H2O]. The prepared adsorbent is expected to be anew inorganic adsorbent for the removal of phosphate ion from wastewater. Keywords: Blast furnace slag, Alkali fusion, Phosphate removal, High selectivity

Sep 1, 2012

By P. Basarova

The attachment of bubbles onto a collecting surface is an ubiquitous natural phenomenon, playing a critical role in numerous practical processes. The goal of the project is to broaden the knowledge about hydrodynamic interactions between small bubbles and large solids that occur in nature and industrial processes. Focusing on collision processes between a single rising bubble (Db<1 mm) and a larger falling spherical particle in stagnant liquid, the theoretical model describing the bubble trajectory is given here. The model is based on analysis of forces acting on the bubble, and utilizes equation for the bubble motion. Mobile and immobile type of bubble surface mobility are considered. The calculated results are compared with the experimental data; here a high-speed video camera was used to capture the bubble motion and bubble-particle interaction. Very good agreement between experimental and calculated data was found. For both types of surface mobilities, the bubble deviation in the horizontal direction is nearly linear. The proportion constant is bigger for immobile bubble surface and increases with the bubble size. Furthermore, particular forces acting on bubble were studied. A similar course of relative bubble velocity and force impact was observed for identical bubble position. For cases when the bubble centre is close to the particle axis, only deflection in one direction is observed. When the bubble is reaching the maximum trajectory, the force ratio is changed. The bubble is firstly pushed away from the particle, but when it is within close distance from the particle, the bubble is pushed towards the particle.

Sep 1, 2012

By R. X. Li

The overall flow-sheet of producing chromium (III) sulfate is described in this paper. The suitable conditions of each process such as sintering, leaching, aluminum removal, reduction, and de-composition conditions were experimentally studied. The results show it is reasonable to produce chromium (III) sulfate with the flow-sheet pointed out in this research work. The final product is Cr2(SO4)3 solution contained 150~250g/L Cr.

Jan 1, 2014

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By J. W. Ahn

Calcined calcium oxide from limestone is hydrated to manufacture calcium hydroxide, and then precipitated calcium carbonate is synthesized from calcium hydroxide. Precipitated calcium carbonate of various morphologies is obtained by controlled conditions of each step and characteristics of limestone, calcium oxide and calcium hydroxide. Especially characteristics of calcium hydroxide have the most influence on morphology of precipitated calcium carbonate character. In this study, therefore, it is investigated the specific surface area of calcium hydroxide and morphology of precipitated calcium carbonate according to hydration temperature. Calcium hydroxide hydrated at high initial temperature has larger particle size than that hydrated at low initial temperature. And formation yield of aragonite precipitated calcium carbonate has improved by using calcium hydroxide had larger particle size (hydrated at high initial temperature).

Jan 1, 2014

By E. V. Mezentseva, S. M. Okunev

"In the article there is set forth a development experience of JSC LEBEDINSKY GOK Beneficiation Plant concerning the plan of increase in the production volumes of the iron ore concentrate with Fe content more than 69.5%. There are considered the issues regarding implementation of the updated process scheme of the concentrate beneficiation using fine screening operation, its industrial tests have shown an exploitability of this development direction. There are described the issues relating to the ceramic filters for dehydration of the additionally-beneficiated concentrate, there are given the production and process figures achieved during the exploitation. The methods of the research. In the paper there have been used the following scientific research methods: the methods of system analysis, mathematical statistics, classification, comparison, modelling, observance, experiment. INTRODUCTION JSC LEBEDINSKY GOK is the largest leading enterprise for iron ore beneficiation and the unique RF producer of the merchant hot briquetted sponge iron (HBI) highly demanded by the consumers. Raw materials for hot briquetted iron production are fluxed pellets produced from iron ore concentrate with Fe content more than 69.5% (additionally-beneficiated concentrate). Strategic program of the plant’s development foresees expansion of production of the highly demanded products that imposes a necessity of expending capacity of the enterprise and implementation in production of modern processes and equipment having low resource intensity and ensuring in addition a high efficiency. Construction of the third stage of the HBI Plant became one of directions for the strategic development of JSC LEBEDINSKY GOK implemented in 2017 that caused a demand in the production volumes and filtration of the iron ore concentrate with Fe content more than 69.5%. Purpose of the work – to develop and to provide a rationalization for efficiency of the production process and filtration of the iron ore concentrate with Fe content more than 69.5% ensuring increase of production volumes and its prime cost."

Jan 1, 2018

By V. A. Ignatkina, V. A. Bocharov, T. I. Yushina, I. M. Petrov, A. A. Kayumov

"The purpose of this research was aimed at increasing recovery of metals from rebellious sulfide polymetallic ores of nonferrous and rare metal deposits. The ores under consideration have common processing features, including textural and structural complex characteristics, irregularity of impregnation and wide range of grain size, up to nanoparticle size, variable complex mineral composition, low content of precious metals etc. This all predetermines the need for advanced processing schemes with deep selective liberation and separation of minerals with intercycle release into rough concentrate and fractional products with the use of multi-stage cycles of individual dressing, based on an optimum combination of various integrated beneficiation and hydrometallurgical processes. The application of existing standard processes does not enable the production of high-grade selective concentrates without reducing the recovery rate due to incomplete separation of fine mineral intergrowths and overgrinding of brittle ore and rock minerals.The combined beneficiation processes for such type of resources, aimed at increasing recovery of nonferrous, rare, and precious metals are based on flotation methods in combination with gravity concentration to produce rich rough collective or selective concentrates, comprising readily floatable mineral fractions. At the same time, hardly recoverable and non-separable mineral associations are released into separate concentrated products for following dressing by individual processes. The proposed combined process provides for successive selective liberation of minerals with release of rich readily recoverable mineral fractions at the preparation and ore beneficiation stages. The hardly recoverable mineral associations shall be released in subsequent operations with the use of dressing, based on a combination of beneficiation and pyro- and hydrometallurgical methods."

Jan 1, 2018

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By Kaustubh Joshi, Pradip, Beena Rai, Venugopal Tammishetti

"Rapid depletion of high grade iron ores coupled with the increasing demand for the blast furnace grade iron ore in recent times has shifted the research focus on the development of appropriate technologies for the utilization of low - grade alumina rich iron ore slimes. These slimes are currently being dumped into tailing ponds owing to their high alumina content. Typical constituent minerals present in the Indian iron ore slimes are hematite, goethite, gibbsite and kaolinite. Considering the fine particle size distribution (<37 microns) in the slimes, selective dispersion-flocculation seems to be one of the most appropriate process which has been explored by us. We present our successful results on a natural iron ore slime sample obtained from one of the mines in India. We have been able to achieve a concentrate assaying >67% Fe, and <3% Al2O3 and 2.8% loss on ignition (LOI) from the slime sample assaying 60.4% Fe, 7.7% Al2O3 and 5.45% LOI with an Fe recovery of 62-69% simply by adjusting the pulp pH. We have scaled up the process to a semi batch scale as a prelude to commercialize it for the beneficiation of low grade iron ore slimes."

Jan 1, 2014

By Rod Hocking, Nenad Djordjevic, Randolph Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures of operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill.Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulated the assemblage of a physical mill."

Jan 1, 2003

By Alexey P. Tatarinov

Under modern economic conditions in Russia, gold heap leaching is the most effective way of investing into gold-mining industry. Gold is recoverable from small-size deposits, low-grade ores from oxidation zone, cut-off grades, and overburden rocks using heap leaching. This technology is cost-effective and allows a saleable metal to be obtained within the first year of operation. The investments for heap leaching are lower than those of for a traditional plant technology. Production cost per one gram of Au is 5-7 times lower than that of during a plant flow sheet. A seasonal development of mines can be possible. With reference to this, heap leaching resembles the technology of placer deposits development. One of the major advantages of heap leaching is the form of the product. Gold can be obtained as dissolved in a clarified PLS, which allows the further quick treatment. The amenability of ores to heap leaching depends on their mineralogical composition. Oxidized porous ores with a good access of a lixiviant to valuable particles can be treated without pre-crushing. Clayish minerals are often found in oxidized ores with free gold. In order to build ground for heap, several major methods combined with various pad materials are used. These methods have been used at many plants and are reliable. The development of heap leaching technology for gold ores for the deposits from Yakutia, Zabaikalsky region, Primorye region, Uzbekistan, Tadjikistan, and Kazakhstan began in the 70s. However, it has been commercially used only since 1990. The first heap leach plants were built and commissioned in the USSR in 1991 at Vassilkovsloye deposit (Kazakhstan) and at Maiskoye deposit in Russia in 1994. Pilot plant testing was conducted in 1996 using ores from Kuranakh ore field, deposits Phiskulturnaya-Kholodnaya and Lopukhovskoye from the Aldan region. After the first successful commissioning of heap leaching plant in Russia, this technology has been commercially applied for deposits. Every year 1-2 heap-leaching plants were commissioned. More than 30 heap-leaching plants have been commissioned both in Russia and in the former Soviet Union using technologies developed by IRGIREDMET. Keywords: cyanide leaching, heap leaching, ore, percolation, solutions, lime technology

Sep 1, 2012

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014