Search Documents

By Luis Bergh, Juan Yianatos, Luis Vinnett

"Process automation as an engineering discipline is more than control systems since it includes industrial instrumentation, such as sensors, transmitters and actuators, as well as control and supervision systems, collection and transmission of data and real-time software applications to supervise and control the operation of plants or industrial processes. In the last several decades, accelerated technological development has provided a variety of software and hardware tools to aid development, maintenance and continuous improvement of automated systems. These developments however seldom reach their full potential in real plants. There are many factors to be considered, among them human capital specific training and the organization model. In this paper, a methodology for training engineers in advanced control and supervision of flotation plants is presented based on study of the application of these technologies in hybrid pilot plants. Since experimentation in real plants may present undesirable risks and costs, and simulation studies are usually limited to some unrealistic conditions, a laboratory where on-line measurements of the hydrodynamic behaviour of a pilot plant is mixed with phenomenological models has been created. In this form, an environment as close as possible to a real plant can be recreated. A flotation column and a circuit of three pneumatic cells are fully instrumented and connected to a PLC and PC network. In the control room, students learn applications of classical PID control in a DCS environment, advanced predictive control, on-line process operation diagnosis, fault analysis, virtual sensors and expert-fuzzy systems. Several undergraduate and graduate courses and theses are supported by this Process Control Laboratory infrastructure. Examples of these applications are discussed."

Jan 1, 2014

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By Shuji Owada, Shinya Suzuki, Chiharu Tokoro, Daisuke Haraguchi, Sayaka Izawa

"Coprecipitation with ferrihydrite has been one of the major treatment method for As(V) removal from wastewater such as acid mine drainage. We already confirmed coprecipitation of As(V) with ferrihydrite consists of two kinds of mechanism; one is two dimensional As(V) uptake to the surface of ferrihydrite by surface complexation and another is three dimensional As(V) uptake into ferrihydrite by surface precipitation. We also already confirmed As(V) adsorption process by ferrihydrite could be quantitatively evaluated by original surface complexation model with parameter values reported by Dzombak and Morel. However, As(V) coprecipitation process couldn’t quantitatively be represented by only the original model. In this study, construction and calculation using surface precipitation model were attempted for As(V) coprecipitation treatment with ferrihydrite. In the surface precipitation model, precipitation was described by the formation of solid compound between ferrihydrite and ferric arsenate. Activity of these precipitates was determined by surface precipitation ratio of FeAsO4(s) obtained experimentally from XANES analyses. Solubility products of surface precipitation of FeAsO4(s) (Ksp_FeAsO4(suf.)) were determined by fitting to sorption densities and surface precipitation ratio in each condition. The values of Ksp_FeAsO4(suf.) were determined 10-7.7 at pH5 and 10-10.2 at pH7, respectively. Based on the obtained Ksp_FeAsO4(suf.) value, As(V) removal and isotherm were calculated for As(V) co-precipitation treatment using surface precipitation model. Good agreement between experimental and calculated values was observed. These results were suggested that the quantitative prediction of As(V) co-precipitation treatment was possible if Ksp_FeAsO4(suf.) value was estimated experimentally."

Jan 1, 2014

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

With significant increase in steel output in the world the price of iron ores has been soaring recently. Especially, there is a strong demand for iron ores in China, leading to more attentions paid to developing low grade iron ores. In this paper mineralogy of nm-of-mine hematite ore was deter-mined, and coal-based direct reduction-magnetic concentration was successfully developed to beneficiate low grade hematite ore. Mineralogy analysis indicates that this hematite ore is a super fine refractory ore, with the main valuable mineral hematite being closely associated with quartz and distributing uniformly and mostly occurring within the size of 3~5J.lITI,leading to being difficult to beneficiate due to super fine hematite and only grading 28.83% Fetotal. This hematite ore failed to be effectively upgraded by traditional processes in trial tests, such as reverse flotation, gravity concentration, and magnetic separation, or the integration of the above processes. In contrast with adoption of the coal-based direct reduction-magnetic separation process, concentrate was produced with high iron grade and metallization degree in the present work, which provides a theoretical basis for utilization of low grade iron ores. By optimization of direct reduction conditions, such as reduction temperatures, duration and mass ratio of reductant coal to iron ore, the reduced ore with 93.72% metallization degree was prepared, and then three-stage grinding-magnetic separation of the reduced ore were conducted, the final concentrate was manufactured, assaying 69.54% Fetotal and 98.01 % metallization degree, and with low content of impurities. This iron concentrate with high metallization degree produced by this process is a superior burden for converter instead of blast furnace. This process is enviromnent friendly by directly making iron using coal and iron ores instead of coke, resulting in less emissions and low production cost.

Jan 1, 2014

By Gaurav Soni, Roe-Hoan Yoon

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model predictions have been compared with the results of a series of laboratory flotation tests conducted using mono-sized glass beads of different particle sizes and contact angles under different operating conditions. Some of the experiments were conducted using a 1:9 mixtures if hydrophobic silica and hydrophilic magnetite, so that the product graded could be readily determined by simple magnetic separation. The model predictions are in good agreement with the experimental results both in recovery and grade. A computer simulator developed on the basis of the model is capable of designing a preliminary flotation circuit on the basis of feed characteristics, e.g., size-by-liberation data, and the hydrodynamic information on the flotation cells to be incorporated in the circuit.

Jan 1, 2014

By R. V. Kononko, A. Yu. Chikin, R. N. Rakhmeev, Yu. O. Fedorov

"The focus of the study is finding a solution that can help to improve diamond recovery in diamond-bearing gravity concentrates upgrading flowsheets. The purpose of the study was to develop and prove scientifically a separation method of diamonds recovery from gravity concentrates regardless of their fluorescence ability induced by X-ray radiation. Two promising recovery methods applicable to diamonds of this type are proposed, i.e. an X-ray radiometric method based on an instantaneous analysis of a secondary X-ray spectrum of separated particles, and a triboelectric method that relies on noncontact measurements of particle charges obtained during its motion in a vibratory tray. As a part of the laboratory study, X-ray fluorescence spectra of the collection of diamond crystals and main associated minerals and rocks at a particle size of -6+3 mm were produced. The analysis of the produced secondary X-ray spectra showed a significant difference between crystals, minerals and rocks within the analytical area of Ca, Fe and Zr due to the absence of calcium, iron and zircon elements in diamonds. Additionally, the scattered X-radiation level of diamonds substantially increased under the influence of X-ray radiation. Such a difference is a physical base of a new method of diamonds recovery from mineral mixtures. The laboratory study on triboelectric characteristics showed that a significant portion of diamonds gained an electric charge of a magnitude that was much higher, compared to associated minerals and rocks. The laboratory and industrial tests and the separation indicators demonstrated a high efficiency. A proposed X-ray radiometric method provides recovery of all types of diamonds regardless of X-ray fluorescence levels, with high selectivity and recovery rate of at least 98%. This proposed separation method is protected by a patent of Russian Federation (No. 2551486, “A method of X-ray radiometric separation of diamond-bearing materials”). Triboelectric separation organized in two stages (main and control) ensures recovery of up to 98-100% of diamonds at a particle size -5+2 and -2+1 mm,. More than 10 triboelectric separators successfully operate in active diamond processing plants in the Russian Federation."

Jan 1, 2018

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 µm to 150 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2014

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By Ivan Bonchev, Elisaveta Djurova, Evgeni Visariev, Viktor Stoilov

"Two types of slag cooling is used world wide - cooling in ladles and cooling in pits. The flotation comparison of the type cooling regimes was done at Aurubis Bulgaria. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag flotation plant processes blend of three parts FSF and one part converter slag. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper content in flotation concentrate is over 20 % and in flotation tail is under 0.5 %. In order to improve the copper recovery, different cooling rate of the liquid slags should be achieved. Three cooling experiments with flash smelting furnace (FSF) slag have been done: two of them in pits with different volume and one cooling experiment in metallic ladle. The ambient air temperature during the cooling tests was from -4 to +4 OC. Laboratory flotation tests in open cycle were done with an aim to compare the slags behaviors cooled at different conditions. In this paper the effect of different cooling on the flotation process will be presented. The copper recovery and distribution by sizes in the tails, copper content in the rougher concentrate, and the concentrate yield are discussed."

Jan 1, 2014

By V. F. Petrov

Today, sodium cyanide is extensively used for extracting gold, however it is highly toxic to the environment if not managed properly. This paper discusses the key challenges presented to gold operations in efforts to come into alignment with the Russian environmental regulations and suggests solutions to overcome these challenges. It is a fact that the major environmental threat cyanide poses to water sources. Therefore, natural water sources should be well protected from the adverse effect of cyanides used in hydrometallurgical processes. For this, the following site procedures and facilities are practiced: in-site and external water recycling systems, reclaim water treatment if required and tailings ponds with water impermeable screens (tailings ponds with controlled leakage). Cost comparison analysis of cyanide destruction methods was carried out. It was revealed that the aldehyde treatment method developed by Irgiredmet JSC demonstrated the best economics. Cyanide emissions are treated by mass-manufactured packed and membrane devices which allow to keep cyanides at the acceptable limiting values established by environmental regulatory agencies.

Jan 1, 2014

By L. Burdukova

"In flotation, depressants are used to reduce the amount of gangue that reports to the concentrate and hence increase the selectivity of the flotation process. At the University of Cape Town extensive batch flotation tests are carried out to evaluate industrial depressants and standard procedures have been developed over the years.This study was conducted in order to develop an improved method for comparing depressants using machine vision as an aid. The modified method of batch flotation involved a test with prolonged intervals between scraping to allow more time for the froth to build up and mature.This method of testing showed increased differences between the flotation performance obtained as represented by grade recovery curves for carboxymethyl cellulose and guar depressants when compared to the standard method of testing with shorter scraping intervals. The improvement was attributed to reduced entrainment resulting from longer drainage time in the froth and therefore yielded a better test for comparing depressants on the basis of true gangue flotation with minimized entrainment. As expected, the sulphide recoveries were unaffected by the change in method. The machine vision system also added to the information obtained during these tests by recording bubble size trends throughout the tests which were later analyzed and related to the amount of flotable gangue in the froth. Modifications are recommended to improve the usefulness of machine vision in batch flotation."

Jan 1, 2003

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

By A. V. Myaskov, V. S. Valavin, K. D’Elia, I. O. Krylov, Vu Van Toan, T. I. Yushina

"The purpose of this research is the development of a technology for processing the concentration tailings of limonite ores at Kamysh-Burun Mining and Processing Complex into an iron- containing product for ROMELT process. In the concentration and metallurgical processing of iron ores, substantial amounts of waste are generated (tailings, slimes, slags, metallurgical dust, etc.) that can be converted into a commercial product if is properly processed. This article presents the results of experimental studies of the feasibility of processing iron- containing tailings of Kamysh-Burun deposit (slimes from Verkhne-Churbash storage facility (VCh sample) and dumped waste of Kamysh-Burun (KB sample)) to obtaining valuable components for further uses. Applying Mossbauer spectroscopy has been shown that the iron minerals in the studied samples are technogenic varieties of iron hydroxides. The most suitable technology is the magnetic roasting process, since iron hydroxides are easily transformed into a magnetic, easily recoverable form. Have been shown the advantages of a two-stage magnetic separation, in a strong field and with polygradient separators. Concentrating this material through magnetic methods makes it possible to increase the iron content to 20-21 %. Magnetic concentration of the deeper layers materials results in iron- containing concentrates with a total iron content of up to 58% whit a phosphorus content of about 2%. Reducing the phosphorus content is possible by blending upper and lower layers of the material at a ratio of 1:1. Thus, it is possible to process the material accumulated in the slime storage facility using the ROMELT process combined with preliminary three-stage magnetic concentration and disposal of tailings with the permissible iron content of less than 5%. Wastes from smelting will be slags suitable for use in construction industry. The Kamysh-Burun material preparation for ROMELT process should be performed applying gravity-washing with separation of the -0.4 mm fraction and additional blending for dephosphorizing the concentrate. The smelting will produce pig iron and slag."

Jan 1, 2018

By A. Kamali Moaveni, A. Boehm

"The current research study addresses a physical separation process of basic oxygen furnace slag “BOF-Slag” (also called Linz-Donawitz “LD” slag) for the removal of phosphorous. In order to recycle the LD-Slag into the steelmaking process, the physical dephosphorization methods are considered. The systematic geometallurgical investigation carried out on particle classes of decreasing size, which were further subdivided into susceptibility classes, shows intimate intergrowth beyond 40 µm due to slag´s fast cooling rate. Generally, LD-slag is constituted of oxide and silicate phases, among which di-calcium silicate “C2S” dominates. About 0.5 mass% of phosphorous was detected in the LD- slag, which is exclusively situated in the lattice of the C2S. The comparatively high grinding resistance (Rittinger index 12.9 cm²/J) of the LD-slag reflects the energy demand to liberate the phosphorous carrying phase from the iron containing minerals, while separation efficiency decreases in the very fine particle size range. Hence, the conversion of the phase intergrowth pattern was considered alternatively to re-build the mineral phase structure of the material to a separable interlock pattern. Carbon dioxide, as the most convenient substance in the steelmaking plants, was applied to digest the C2S in the presence of water and to reduce the basicity of the slag slurry. As a result of C2S-CO2 chemical reaction, calcite and calcium silicate are precipitated at the surface of the oxide particles and carried between 25% and 75% of the total phosphorous, respectively. Accordingly, the mobility of the phosphorous content phase to the top of the grains serves the possibility to separate the precipitated layer by mechanical attrition process. This paper is focused on the impact of the intergrowth pattern alteration on the slag´s separability characteristics. Moreover, the operating conditions of the carbonization process, such as temperature and pressure, on the deconstruction kinetics of the C2S and the generated products will be considered. INTRODUCTION The steelmaking BOF-Slag is a stony aggregate waste from the steel manufacturing process. The investigated slag by the current research work was provided by voestalpine steelmaking plant in Linz, Austria. The current legislative situation in Austria restricts the historical application of slag as construction material, due to the high level of heavy metals content and corresponded land-filling and transportation costs of slag, therefore the demand for recycling of BOF-Slag to the steelmaking process has raised, as an alternative application. Statistically, voestalpine steelmaking plant produces about 130 kg BOF-Slag per ton of final steel product, which serves annual BOF-Slag production of 700,000 ton, approximately."

Jan 1, 2018

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By D. Vega, P. R. Brito-Parada

"Small diameter (10 mm) hydrocyclones have been applied successfully for the separation of particle suspensions in the micron size range. These hydrocyclones are attractive because they show a bypass fraction larger that the water recovery, resulting in a high particle recovery to the underflow as well as low water recovery. However, this is a disadvantage when the purpose of the hydrocyclone is classification because of the large amount of fine particles that are misplaced in the underflow. The aim of this study is to explore, experimentally and computationally, the influence of design parameters on the classification process. In this work, a full factorial experimental design was defined to carry out comprehensive experimental tests using glass beads (0-20 µm) as the particulate system. We show that the dimensions of spigot and vortex finder diameter can be effectively manipulated to change the separation performance of the system and the energy consumption. A CFD model was developed that is able to predict particle size distribution. The numerical results for the partition curves showed very good agreement with the experimental data. INTRODUCTION Small diameter hydrocyclones are a very attractive separation technology for fine particle suspensions. Since the hydrocyclone diameter is directly proportional to the cutsize that can be achieved, 10mm hydrocyclones have been shown to be very effective in collecting particles in the micron-size range. In addition, while in large hydrocyclones the bypass, i.e. the fraction of particles that report to the underflow without classification, is similar to the water recovery, in 10mm hydrocyclones the bypass fraction is considerably larger than the water recovery. Its high particle recovery and low water recovery makes small hydrocyclones ideal for ultrafine particle classification and dewatering applications in mineral processing. The separation of mineral suspensions achieved using small hydrocyclones has been the focus of various studies. Pasquier and Cilliers (2000) derived a general classification model from experimental data of fine silica concentration in 10mm hydrocyclones; the model was able to describe the fish-hook partition curve. The effect of operating conditions has also received some attention in the literature. Cilliers et al. (2004) showed that an increase in temperature positively effects the recovery of fine silica particles in small hydrocyclones, by increasing the bypass and decreasing the cutsize. Neese et al. (2015) showed that the cutsize in 10mm hydrocyclones can be further decreased by operating at higher pressure, which also trebled the throughput."

Jan 1, 2018