Search Documents

By Klaus M. Hahn, Kurt Aasly, Jutta Lennartz, Hermann Wotruba, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Seafloor massive sulphide (SMS) deposits have been identified as important marine metal resources for the future. However, literature on mineral processing of SMS is currently limited, and to date, no research has been published on processing of SMS from either active or inactive hydrothermal vent fields on the Arctic Mid-Ocean Ridge. In this paper, individual SMS rock samples from the Loki’s Castle area were tested. Chalcopyrite, isocubanite and sphalerite represented the main copper and zinc bearing minerals in the SMS samples, whereas the gangue consisted of barite and silica. Based on the X-ray transmission response (XRT), i.e. differences in the atomic number of elements in tested samples, and using portable XRF (PXRF) values of elemental composition, individual particles were classified as a either product (low barium / high to low silicon / high copper and zinc) or waste (high barium / high silicon / low copper and zinc). The classification was based on the elemental composition of the samples with the cut-off grade equal to 0.5% for copper. It was shown that the XRT discrimination analysis correlated well with elemental (PXRF) data classification. The results clearly indicate that X-ray transmission sensor-based sorting can be used a useful technique for preconcentration of SMS rock samples. INTRODUCTION Due to different compositions of investigated samples, sensor-based sorting is a useful technique for preconcentration of different materials. The aim of using sensor-based sorting is to upgrade an ore by reducing the quantity of overall waste material reporting to the next processing stage. This can be achieved by eliminating (reducing) the waste fraction. By applying sensor-based sorting, the energy consumption for particle comminution as well as the required process water and reagents can be decreased. The total volume of the waste rejection leads to a proportional reduction in the total energy costs (Lessard et al., 2014, 2016)."

Jan 1, 2018

By Gorki Davila, Irineu Brum

"Brazil has large reserves of coal (32 billion tons) located predominantly in the south of the country. Despite the relative ease of exploitation, these resources have been underestimated as a source of energy. Currently the country's strategic planning aims to minimize the gap between coal and resources traditionally used in the Brazilian energy matrix. In this scenario the processing of Brazilian coal by flotation appears as a promising alternative, having been successful in mineral systems containing fine particles This paper aims to study the overall process of flotation for a specific Brazilian coal. The material used in this study consists of fine coal that is usually discarded as waste and deposited in the tailings dam. The objective is to recover carbonaceous matter and reduce the ash and contaminants grade. The variables analyzed were the influence of size particle, solids concentration in the pulp, the concentration of surfactants and frothers to be used. The results showed that it is possible, from a feed with around 65% of ashes, to obtain products with approximately 35% ashes with mass recoveries about 40%. The types of collector reagent and foaming employees result in different concentrates. This study also presents a preliminary analysis of the effect of water recovery in concentration parameters."

Jan 1, 2014

By Janne Kauppi, Kaj Jansson, Piia Suvio, Saara Hagnäs

"Historically the focus at the mineral processing sites has been to improve the production operations, while little focus has been set on how factors, such as the quality of water used in the process affects the metal recovery. Simultaneously increasing public pressure and water scarcity is driving the mining industry to recycle more water back to the process, which in turn leads to accumulation of impurities within the recycled water. This paper presents a concept for a systematic approach on targeting the impurities that have a negative effect on the metal recovery at the flotation circuit by using a novel solution called Process Water Recycling Plant (PWRP). These plants are designed with specific ore type in mind. PWRP produces cost-effectively process water to different target qualities, especially for flotation purposes enabling higher and more stable flotation recovery. It consists of pre-designed and standard water treatment units for a wide range of volumes. The application-specific configuration of units is governed by the water quality requirements, and can be designed according to specific customer needs. Testing has been carried out in order to investigate, which recycling water impurities affect the different ore types and how the metal recovery in flotation is affected as a consequence of the poor-quality water. The results indicate that every ore type is impacted differently and without a good understanding on how the water quality impacts the process performance, adverse effects on the flotation recovery can occur.INTRODUCTION With a focus on where water is used within the mineral processing, it has become evident that even though water is used in several different processes, majority of the water losses within the site occur at the tailings processing and the tailings storage facility. New tailings management technologies that can increase the recovery of water are actively being developed, but the key to improving the efficiency of water use and reducing the operational risks lies in closing the water loops and increasing the slurry density in the tailings processing. With this shift from conventional tailings technologies towards paste and dry stacking, water efficiency is vastly improved, but it might in turn lead to process water challenges with impurities, reagents and fines being recycled and accumulated within the production processes."

Jan 1, 2018

By M. Karamoozian

Modelling and optimisation of the power draw of large SAG mills are important due to the large power draw which modern mills require (5~10 MW). The cost of grinding is the single biggest cost within the entire process of mineral processing. Traditionally, modelling of the mill power draw has been done using empirical models. Although these models are reliable, they cannot model mills and operating conditions, which are not within the model database boundaries. Also, due to their static nature, the impact of the changing conditions on the power draw, within the mill, cannot be deter-mined using such models. Despite advances in computing power, on-line modelling of large plant scale mills could be a time consuming task. On the other hand, using on-line parameters for model-ling, result in more reliable control of SAG mill without performing any more costly tests. In this paper, SAG mill power draw is modelled using neural network approach. Six inputs, namely: solid percent, two bearing pressures, noise, recycle and feed rate were used to model the power draw. The produced model shows an acceptable correlation coefficient, R2 =0.9623.

Jan 1, 2014

By S. M. Wen

In mineral processing, the settling of mineral particles in water, the flow of ore pulp, the dewatering and filtering of concentrates and so on, are related to the pulp viscosity. While the interaction between mineral particle surface and water affects directly the pulp viscosity. Therefore, it is of great value to the development of mineral processing theory to research the effect of mineral particle surface on the water viscosity in boundary layer. In micro-fluid, the effect of mineral particle surface on the water molecules in boundary layer can not be ignored. The water viscosity in boundary layer and the effect of the nature of mineral particle solid surface on the viscosity are analysed based on the deduction of attraction potential energy formula of mineral particle surface to the water molecules in boundary layer. The results show that the attraction potential energy of mineral particle surface to the water molecules in boundary layer is determined by the properties of solid molecules and fluid molecules and varies inversely as the third power of the distance from mineral particle surface. The water viscosity in boundary layer consists of the viscosity of free water and the additional viscosity resulting from the attraction of mineral particle surface. The increment of the viscosity caused by the attraction of mineral surface is µs. This additional viscosity is also inverse ratio to the third power of the distance from mineral particle surface. The greater the dipole moment, the polarizability and the ionization energy of mineral particle solid surface molecules are, the higher the attraction potential energy of mineral particle surface to the water molecules and the water viscosity in boundary layer are. The thicker stationary water boundary layer is d0. The higher the µs is, in other words, the greater the attraction of solid surface to water molecules is, the thicker the stationary water boundary layer becomes when free water viscosity is constant.

Jan 1, 2014

By H. Tiefel, M. Schneider, T. Neesse, J. Regler, J. Dueck, F. Donhauser

In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Control systems of large hydrocyclones are usually fitted with controllable underflow nozzles, which is not practical for small hydrocyclone batteries. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was invented at the LUR in cooperation with AKW Apparate und Verfahren GmbH & Co. KG. This process was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.

Jan 1, 2003

By L. A. Vaisberg

"Mining processing plants are the most high-performing industrial enterprises in the world economy system. Even at an average-scale mining enterprise, the grain-size separation equipment continuously processes 105 to 106 dissimilar mineral particles per hour. In separation by physical properties, their number increases by at least 10 to 50 times. Mathematical modeling of such a high flow of discrete particles is carried out using two different approaches: the discrete-particle and the phenomenological methods. The calculations demonstrate the possibility of handling big data when describing the processes of separation of granular material. INTRODUCTION The interest to the screening process and the process of formation of new screen designs in Mekhanobr is traditional since the moment of its foundation. It is symbolical that the first publication of the Mekhanobr proceedings in 1924 was the monograph dedicated to screens and screening products as such, which was the first one in the world at that moment. It was a book of Prof. L. B. Levenson, one of the founders of Mekhanobr, who headed the Technical Bureau of the Institute. Vibratory screening is the most mass process in the technologies of solid minerals processing, which determines significantly the energy demands of crushing and grinding cycles, and at some enterprises determines the quality of the final product, for example in case of crushed stone, coal or abrasive materials production. The general understanding and simulation of the process of poly-dispersed granular materials vibratory screening was developed at several conceptual levels taking into account the features of classification of materials with different size and density.Considering the real industrial processes of vibration screening, it shall be noted that at the sieve surface of the screen in the initial part of the deck the classification in a thick material layer (in natural conditions) occurs, which further transfers to a thin layer (free movement). In the process of screening of light minerals, for example coal or metallurgic feedstock, screening is mainly performed in the thick layer."

Jan 1, 2018

By S. M. Mustakim

Red mud is the major waste material produced during digestion of bauxite ores with caustic soda in alumina production following the Bayer?s process. Its disposal remains a worldwide issue in terms of environmental concerns. A lot of research and developmental activities are going on throughout the world to find effective utilization of red mud, which involves various product developments. At present, building materials, industries are fast growing industrial sector where the need of various raw materials is enormous. The use of red mud in building material production is one of the options for conservation of natural resources and reduction of environmental pollution. A cost-effective and energy efficient mineral cementation process has been developed at CSIR-IMMT, Bhubaneswar for use of red mud in manufacture of building brick, block and aggregate. The red mud is an alkaline material, which contains both leachable and non-leachable soda along with different mineral constituents of alumina, iron and silica. The effort has been made to use the mineral constituents of red mud to develop cold setting building brick by mineral cementation process using a binder specially prepared from Portland Slag Cement, Lime, Gypsum and Alkali metal sulfates. The red mud has been used from 40 to 70% by weight along with fly ash and binder in development of cold setting building brick conforming to the specification of IS:12894:2002.

Sep 1, 2012

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

"Oxidized nickel ores are important source for nickel production in Russia. Considerable explored reserves of oxidized nickel ores with relatively low nickel content, about 0.6-1.4%, are concentrated in the Ural region of Russia. Conventional process flowsheet with the use of blast matte smelting, applied in particularly by JSC “Ufaleynickel”, proves itself as extremely low-margin technology. This paper will examine development of a new more cost-efficient process involving integrated treatment of oxidized nickel ores using the ore from Serovskoye deposit as an example. Target products of this process are hydrate residues containing up to 15 % of nickel and 0.3 % of cobalt, as well as saleable salts of magnesium sulphate and ammonium suplphate. This innovative process includes roasting of a mixture composed of ground ore and sulphuric acid at 650 °?. Sulphate roasted product is then leached in a weak sulphuric acid solution with the following separation of liquid from insoluble solids. Sulphate solution is neutralized by aqua ammonia in two stages until media pH is 3.0-3.5 and 7.5-8.0 with detachment of iron- and nickel-bearing hydrate residues respectively. The mother solution is boiled out resulting in salt crystals which are then dried and roasted at 500-600 °? to obtain magnesium sulphate. The gases generated during salts roasting are captured with production of ammonium sulphate. The developed technology demonstrates higher potential in terms of its economics and eco-efficiency comparing with the conventional process. This innovative technology for integrated process of oxidized nickel ores was patented in Russia.INTRODUCTION Development and industrial implementation of efficient technologies to process oxidized nickel ores is a very important task for non-ferrous metallurgy of Russia. The main reasons for the required technical upgrade of the plants processing oxidized nickel ores is depletion of rich ores, increase of energy resources costs, amplification of environmental and production standards. Due to this, transition from conventional pyrometallurgy to cost-effective hydrometallurgical technologies of ore liberation and solutions processing is logical and corresponds to the worldwide practice of Ni production from oxidized nickel ores."

Jan 1, 2018

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By Shen Zhengchang

Based on the flotation features of coarse particle mineral, a new type of impeller & stator unit is developed. Particles suspension state generated by this impeller & stator unit under different speeds are tested in laboratory, and critical impeller speed suit for coarse particles flotation is presented. Comparing particle suspension parameters of the new impeller & stator unit with that of KYF impeller and stator unit, it comes up that the distance between the interface of two slurry circulation channels and the cell bottom is larger in the flotation cell with new impeller & stator unit. The test results indicate that the new type of impeller & stator unit is suitable for processing coarse particles due to its good suspension capacity for coarse particles. Keywords: coarse particles, flotation, suspension, critical speed, impeller and stator unit

Sep 1, 2012

By M. Etelapaa

A new approach to controlling the process of selective flotation of sulphide minerals from pyrite in a lime environment is covered in the presentation. Advantages of process control based on the electrochemical potential of slurry controlled by ?? ? electrode are proved and compared to conventional methods of ?? ? metering and conductometry. Keywords: flotation, electrochemical potential, automation dosing system, neural network

Sep 1, 2012

By Sergey S. Gudkov

In the current climate of changing the approach to mining and treatment of mineral resources, processing technologies are being developed that require little maintenance and are economically as well as ecologically sustainable. This may also involve the development of entirely new ways of ore processing. One promising approach is to use bioleaching for the pretreatment of gold refractory ores to cyanidation. Capital costs for vat bioleaching of concentrates and ores are very high and cannot be applied for small or medium-size deposits. IRGIREDMET JSC carried out bio heap leaching test work on refractory ore samples from three Russian deposits. Following this biological treatment a combination of flotation, vat bioleaching, and cyanidation are used to recover gold. After heap bioleaching, gold recovery was 75-80 per cent. It was found that efficiency of heap bioleaching process depends on ore feed size. High duration of this process is another feature and it lasts for about a year. This process can be also used for carbonates in the combination with other process during which acid generation occurs. The results of our studies have shown that this technology is amenable for refractory gold ores. Its introduction allows an increase gold recovery and to solve a number of environmental problems. Keywords: heap biooxidaton, the refractory of the ores, the degree of oxidation, arsenopyrite, pyrite, CIL

Sep 1, 2012

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By Leming Ou, Qiming Feng, Yiping Lu, Pengyu Zhang, Qing Shi, Kun Liu, Guofan Zhang

"This paper introduces the mineralogical analysis of certain polymetallic copper-zinc ore in China with the aim of improving the flotation process. The main valuable elements, mineral phases and compositions of run-of-mine ore were inspected by the X-ray Fluorescence (XRF) and chemical analysis. For a deep known of the old process defects, Mineral Liberation Analysis system (MLAs) was employed to investigate the minerals liberation degree of selected key slurry points. Analysis results show that the run-of-mine ore belongs to the original copper-zinc polymetallic symbiotic ore at low oxidative level, which mainly contains 0.16% Cu, 4.43% Zn and 0.88% Sn. Gangue minerals are mainly silicate minerals, and zinc mineral is sphalerite. MLAs test illustrates that about 86% sphalerite has been dissociated in zinc flotation feed. In the current flotation process, over grinding of sphalerite monomer and insufficient liberation of intergrowths are the key problems need to be solved imminently. Up to this point, a new process consisted of two steps roughing unit is submitted in this research. It contributes two positive effects on zinc flotation performance: (i) separating sphalerite monomer timely to decrease overgrinding; (ii) improving zinc minerals intergrowths liberation efficiency. Flotation results indicate that the zinc concentrate grade increased 0.90% and the recovery improved 0.96% in the new flotation processINTRODUCTION Mineralogical analysis mainly focusses on solving mineralogy problems in minerals processing, assisting in minerals behaviors prediction and control for separation engineering (Falkovich, et al., 2001; Hillier, et al., 2003; Schouwstra and Smit, 2011). Process defects searching becomes its ordinary work, and flotation optimization appears to be its targets gradually. For example, Lucky Friday mine company (Idaho America) fails to obtain qualified lead concentrate as the change of ore properties (Nadoll, et al., 2011). Mineralogical analysis ascertains that there are too many dissociated sphalerite, pyrite and gangue particles exist in lead concentrate. According to this, more cleaning units are added to solve problems effectively. Kanowna Belle mine (Australia) takes a flash circuit in operation successfully with the aim of optimize flotation process, under the helps of mineralogical analysis and industrial test (Newcombe, et al., 2013). Lotter N.O. (2011) gives a deep description on how mineralogical data assisting mineral processing engineers to design and optimize flowsheet. For decades, quantitative and automated mineralogy techniques (Andersen, et al., 2009; Gu, et al., 2012; Oghazi, et al., 2009; Yu, et al., 2007) get well developed and hugely improve the veracity and repeatability of minerals properties measurement. Among these, MLAs (Gu, 2003) provided by JKMRC (Julius Kruttschnitt Mineral Research Center) is critically acclaimed all over the world. This analysis system can measure mineral phases composition and content, particles size, minerals occurrence and liberation degree directly."

Jan 1, 2018

By C. Perez

In mineral processing plants it is important to estimate rock composition, size and grindability to improve control of the grinding process. It is well known that variation in ore grindability and size distribution directly affects mills power consumption and throughput. This paper extends a general machine vision approach for on-line estimation of rock mixture composition using color information. Our proposed rock lithological recognition method requires the following steps: division of each image into sub-images, color feature extraction using the Binary Quaternion-Moment-Preserving thresholding technique (BQMP) and support vector machines (SVM) for classification. The BQMP thresholding technique splits the image in two and chooses representatives of each half using the histogram as features. The statistical parameters of the color data can be expressed using the quaternion moments into the representatives. This method can be recursively applied to the sub-images, obtaining 5x2n features in n iterations. Once the feature vector has been computed, each vector is assigned to one of three classes using a classifier. The method was tested on a database containing 20480 sub-images (64x43 pixels) of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets: 15360 sub-images used for training and cross validation and 5120 sub-images used for test. The classification accuracy was compared with a method previously published based on a mixture of principal components analysis (PCA) for color, and wavelet texture analysis (WTA) for texture feature extraction. WTA-PCA approach reached a 76% accuracy in test while our BQMP method reached 90% of classification accuracy using only color features. Experimental results show that our proposed method yields excellent results compared to previously published results. Keywords: rock classification, lithological classification, grindability estimation

Sep 1, 2012

By A. Makavetskas

"The purpose of the research is to study the mineralogical features of the structure of the wall accretion formed during melting on the working surface of the walls of metallurgical aggregates and adversely affect the stability of the lining of blast furnaces (BF). We presented the results of studies of the material composition of lining and wall accretion of the furnaces of blast furnaces of the metallurgical plant specializing in the smelting of ferromanganese, nodular and pig iron. It is established that the garnissage is an aggregate of layered texture, formed as a result of the crystallization of slag and metallic melts. Refractory calcium and magnesium silicates and aluminosilicates (minerals of the melilite group, leicite, olivine group minerals) and amorphous glassy oxide solid solutions of variable composition crystallize from the slag melts in the upper part of the hearth. In the slag matrix, inclusions of carbon (amorphous and graphite) and products of crystallization of metallic melts of alpha-iron, iron carbides and / or manganese are observed. Evidence of carbon evolution (in the form of graphite) is precisely in the crystallization of metal melts, there are significant differences in the structure of carbon in coke and in the garnissage. The conducted studies confirm that it is impossible to obtain reliable information on the material composition of new formations in the blast-furnace process without using a complex of modern methods of technological mineralogy.INTRODUCTION The formation of the wall accretion (garnissage) - a solid protective layer as a result of smelting products crystallization on the inner (working) surface of the liner. This is due to the design of blast furnaces with a high-efficiency heat sink using copper coolers and the use of carbon blocks with high thermal conductivity in the lining. The objective of the study was research of the material composition of the lining and wall accretion of the blast furnace hearth of one metallurgical plant that specialized in smelting ferromanganese, nodular and pig iron, to assess the effect of new formations for stability of the lining of blast furnaces (BF)."

Jan 1, 2018

By A. Gülmez

The complex ore deposit containing fluorite, barite and bastnaesite minerals is located in Beylikova Region of Sivrihisar town of Eskisehir Province of Turkey. The ore contains 40.80% CaF2; 35.35% BaSO4; 2.01%Ce; 1.5% La; 0.39% Nd and 0.1% Th. Barite recovery from this ore by flotation of the HCl leached tailings is presented in this paper. Rare earths are recovered by leaching. The leached residue (tailings) containing fluorite and barite is subjected to froth flotation to recover barite. The effect of pH and collector concentration on the flotation of barite have been studied in this work.

Sep 1, 2012

By G. Semenchenko

Heterotrophic microorganisms Pseudomonas aureofaciens, microscopic fungi Fusarium sp. and their combinations with some chemical substances were used for gold leaching from refractory ore and flotation concentrateof Akbakaj deposit. All biological additives raised the speed of noble metals dissolution. The best results of gold extraction from ore were in the presence of bacteria or their associations with other solvents and from flotation concentrate in the presence of fungus - 30 % of additional amount of gold. The maximum extraction of gold speed value was during the first 8 hours of process. The electronic-microscopic researches of the ore samples showed almost complete decay of pyrite and arsenopyrite under bacteria influence whereas at chemical leaching most of these minerals stayed uncrushed. The presence of microscopic fungi in flotation concentrate during leaching provided full distraction of pyrite, but some crystals of antimony and arsenopyrite were undestroyed. During cyanide leaching of flotation concentrate there were accumulation of antimony and incomplete pyrite decomposition. Keywords: gold bioleaching, bacteria, fungi, complex solution

Sep 1, 2012

By Shailin Lalloo, Allan B. Nesbitt

A fluidised bed was exposed to high gravities by placing it in a centrifuge. The bed expansions were measured and compared with the bed expansions predicted by the Richardson-Zaki model (1954). The Richardson-Zaki model was found to predict effectively the fluidisation behaviour of defined particles in this increased gravity environment.

Jan 1, 2003