Search Documents

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016

By N. Bartie

Realising the circular economy (CE) is faced with some significant challenges. Process metallurgy and its infrastructure play key roles at the heart of making the CE work. Therefore, the enabling role of process metallurgy within the CE will be central to the discussion in this paper, touching among others on product and system design as well as the key metallurgical and other process fundamentals that need to be investigated and understood to make the CE a reality. The central role of materials and its processing will be discussed in an integrated circular cities perspective. A key focus will be a discussion on designing a resilient “Smart Materials Grid” using and innovating metallurgical process engineering tools, which will manage the flows through Sustainable Circular Cities. The discussion will be using copper as leitmotiv of the discussion i.e. from copper ore, to metal, to complex products, recycling, product design and simulation and its impact. INTRODUCTION The transformation of our economies from linear to circular models in which waste materials become resources is the focus of the Circular Economy (CE) paradigm. Its important intentions: to take control of the damage we have been doing to the planet to ensure its livability and the welfare of future generations. This can only be achieved through careful utilisation of human, natural and economic resources. The concept is derived from several others (Beaulieu et al., 2015), of which Cradle-to-Cradle, Extended Producer Responsibility (EPR), Industrial Ecology, and Life Cycle Thinking are just a few. Other relevant concepts include resource efficiency (RE), design-for-recycling (DfR), and various others discussed by Blomsma and Brennan (2017) and Homrich et al. (2018), as well as various R-hierarchies e.g. Reduce, Reuse, Recycle (3R). However, does society comprehend these concepts, the actors and actions that influence them and how they interact? Do we know the limits of CE? Does society understand the key role of Copper and other metals to rendering the CE operable? True life cycle and systems thinking, focussed on simulation-based, process and metallurgical design are required to answer these questions. Lieder and Rashid (2016) identify nine widely-varying fields that study the concept ranging from sustainability sciences and engineering to economics, business, law, and social sciences. Overlap between questions addressed highlights the need for interdisciplinary collaboration (Nanz et al., 2017) in the assessment of the current status, and further steps needed to transform to CE. This doesn’t apply just in academia, but also in industry where concrete implementation of CE needs to occur at multiple levels, thus necessitating cooperation between government, civil society and other stakeholders (Beaulieu et al., 2015).

Jan 1, 2019

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

By K. E. Haque

"Radium is selectively leachable from uranium ores with various types of lixiviants. Among a number of lixiviants tried on Midwest Lake uranium ore, KCl provided the highest per cent of radium extraction (60%-65%). Leach results further confirmed that a certain portion of Ra is not amenable to KCl leaching. More than 99% of the dissolved radium could be removed by treating the KCl leach liquor with barite or with radium selective complex resin (XFS-43230 resin of Dow Chemical Inc.) or by precipitating as RaBaSO4. Uranium leachings from the Ra-preleached uranium ores indicate that radium leaching prior to uranium may be applied as an extension to the conventional or alternative (i.e. acid chloride) leaching process of uranium ores in order to yield environmentally acceptable tailings (in terms of radium in the solids).IntroductionAt present, radium is considered as an environmental issue, particularly for uranium ore mine mill operations, rather than a commercial commodity. Radium was once a highly priced commodity ($180/mg during the first great war) but now it hardly has any commercial value. Its principal applications were in the field of cancer treatment and in the manufacturing of lwninous dials for watches. Nowadays readily-available synthetic radioisotopes are finding applications in place of radium.Because of scarcity and high toxicity, further commercial applications have never been explored.Radium was first discovered and extracted from uranium ore by P. Curie, M. Curie and G. Bement in 1898. Radium is widely distributed in nature but in exceedingly minute quantities. It is one of the daughter products of uranium or thorium and its maximum concentration is 3.3 x 10-7 part/part of U(21). Because of its short half-life (approximately 1620 years) in a geological time scale, its occurrence in nature as a distinct mineral is most unlikely.The details of the original radium leaching process developed by the Curies and Bernont are in the literature. This process essentially involved the roasting of uranium ore with caustic. carbonate followed by sulphuric acid leaching. The precipitated RaSO4 and BaS04 were treated with boiling Na2CO3 to convert them into the corresponding carbonates which later were dissolved in HCI. RaCI2 and Ba02 were separated and concentrated from the chloride liquor by fractional crystallization. But, in the course of time several modifications were made or proposed to the original process. Regardless of the process employed 226Ra extraction from the uranium ore was seldom better than 90%, and further as much as 20% 2URa loss took place during the concentration and purification process."

Jan 1, 1987

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By J. Shibata, N. Murayama

"Rare earth elements are present in more than 100 minerals, of which monazite, bastnaesite and xenotime are typical. Rare earth elements have excellent chemical and physical properties for industrial use in functional materials such as phosphors, magnets, electronic components, abrasives and catalysts. China produces more than 90 % of the world’s rare earths, and Chinese trends significantly influence the demand and price of rare earths. From the viewpoint of resource securement, it is desirable to separate and recover rare earth elements from low-grade resources and wastes. Phosphate gypsum, which is a by-product of wet phosphoric acid manufacturing, contains low concentrations of rare earth elements. In this research, the separation and recovery of rare earth elements from phosphate gypsum were investigated. A series of recovery methods including washing of phosphate gypsum, leaching of the rare earth elements with sulfuric acid, adsorption and desorption of rare earth elements by using ion-exchange resin, and precipitation of rare earth oxalates were carried out. The separation of rare earth elements from Ca2+ simultaneously leached from phosphate gypsum was also investigated."

Jan 1, 2014

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By C J. Coveney

This paper, after a brief introduction to the mineralization and structure in the mine area, outlines the methods now being employed for grade control at Bethlehem Copper Corporation. Sampling, subgrade drilling, blasting and the actual outlining of the ore are among the topics covered. The paper concludes with a summary of the results obtained, showing a reduction in dilution and an improvement in the grade of the copper ore going to the mill. Introduction T HE Bethlehem property is located in southern British Columbia in the Highland Valley about 30 miles southeast of the town of Ashcroft. The property is located within the Guichon batholith. The rock comprising the batholith is a massive, coarse-textured diorite, which, at Bethlehem, has been intruded by a younger quartz diorite, porphyries and breccia, referred to as the "Younger Complex." Mineralization, consisting of chalcopyrite and bornite with minor pyrite and molybdenite, occurs as disseminations, fracture fillings and coarse blebs. The ore zone lies close to the Guichon -Younger Complex contact where, prior to the development of the breccia, the rocks were shattered and jointed. Subsequent mineral

Jan 1, 1965

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y&apos; phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

By M. Boussuge

Ceramics and refractories have many common constituents and consecutively exhibit several analogous properties. For example, concerning the thermomechanical properties this paper will focus on, the type of creep that can be observed in both materials is often the same (kinematic hardening). Changes in microstructure (phase transformation, dehydration, sintering, crystallisation,...), induced by heating and/or cooling, can also drastically modify the mechanical behaviour of ceramics and refractories. But the coarse granulates, the porosity and the impurities contained in industrial refractories may lead to specific responses of this material to thermal and/or mechanical loadings. In particular, some differences can be observed with technical ceramics in the main type of damage observed in service : diffuse damage in refractories (microcracking) and localised damage in ceramics (macrocracking). In this paper, the possibilities of transferring a part of knowledge from ceramics to refractories will be discussed, in the field of thermomechanical properties : experimental characterization techniques, mechanical behaviour models. Finally, some problems caused by scale effects and by the integration of thermomechanical properties of refractories in the numerical simulation of industrial structures will be evoked.

Jan 1, 2004

In recent years, China and India have emerged as major players in the copper sector. Over the last decade, around 50% of additional global refined copper usage growth can be attributed to them. The paper provides an overview of the current and future copper supply and demand situation in both countries. Results from two market studies commissioned by the International Copper Study Group (ICSG) are complemented with recent copper statistics on North-East and South-East Asia, as well as further sectoral analysis. Developments and trends in copper mining and metal production, semis production, and major end use areas are highlighted. While providing insights into sectoral patterns and growth trends, the paper provides the basis for comparing structure and output of the copper sectors in some of the major copper-using countries in Asia. Afterwards, the current copper reservoir in use associated with infrastructure, buildings, industrial equipment, transportation systems and households is assessed using the ICSG Copper Flow Model. Finally, the identified copper flows are analyzed regarding the potential impact on the future world supply and demand situation.

Jan 1, 2007

By N. Schmitt, E. Blond, F. Hild

Working linings of steel ladles progressively damage during the steel manufacturing process due to both severe thermomechanical and chemical stresses. In the framework of the coupling scheme proposed by Blond et al. (1), this study examines the effects of the thermomechanical loading on the onset of microcracking by considering that the complex microstructure of the slag-impregnated brick is fixed during the steelmaking process. The behaviour of the refractory is identified by using thermoelastic-(asymmetric)viscoplastic constitutive equations. Numerical simulations of a simplified geometry of the lining subjected to cyclic thermal loadings at the inner side are shown. Two cases are analysed, namely, i) the material is a homogeneous continuum with a thermoelastic-(asymmetric)viscoplastic behaviour, ii) the material is porous and saturated by liquid slag, and the skeleton has the previous non-linear behaviour. The stress and strain fields are shown, and for the porous medium the interstitial pressure of slag as well. Comparisons between these assumptions are made to assess the role of slag on the degradation of the working lining.

Jan 1, 2004

By K. G. Eriksson

"The first tentative test made to try rubber lining in grinding mills was made in the early twenties. However, because of poor rubber compounds and design the results did not prove to be promising.In the early sixties successful trials of rubber linings were carried out as a result of a cooperation between boliden AB and Skega AB.One of the reasons rubber was not used earlier for linings was the difference in wear characteristics between rubber and steel. The ability to successfully develop rubber mill liners depends on three factors:l. Design2. Material (rubber compounding)3. Experience (knowledge)DESIGNThe main difference between steel and rubber, in material aspect, is the elasticity and the low tensile and shearing strength of rubber. It is necessary to take maximum advantage of the elasticity and to reduce tensile and shearing forces by minimizing the sliding of the mill charge. This is accomplished by using the Lorrain type of liners, i.e., lifter bars and plates. It is, however, necessary to keep a certain balance between lifter bars to optimize liner life and grinding performance."

Jan 1, 1983

By K. L. Eastwood

The ISA PROCESSTM cathode plate is characterised by its copper coated suspension bar, coupled with a blade employing austenitic stainless steel alloy 316L. The blade material has become the mainstay of the technology and has been closely copied by competing cathode designs. Improvement to the cathode plate design remains a key area for research, and ongoing developments by Xstrata Technology&apos;s ISA PROCESSTM have recently been commercialised. Two such developments are the ISA Cathode BRTM and ISA 2000 AB Cathode. The ISA BR cathode is a lower resistance cathode that has proven to enhance operating efficiencies. The AB cathode was designed to improve stripping inefficiencies in the ISA 2000 technology. These developments have now had time to mature and their long term performance will be discussed. Rising material costs and the desire to extend the operating boundaries of the standard 316L cathode plate has triggered a number of significant advances. These involve the use of different stainless steels as alternatives in some operational situations. The technical aspects and results of commercial trials on this development will also be discussed in this paper.

Jan 1, 2007

By J. Lu

The impact of acid treatment in agglomeration/acid curing on copper extraction and acid consumption was investigated with respect to acid dosage and moisture. Without the addition of water, no agglomeration occurred. At an acid dosage above 15 kg/t, the acid was not completely consumed during acid curing. With the addition of 6.2% water, the particles agglomerated together. Copper, iron, magnesium and manganese were dissolved as sulfates and enriched in the fine fraction of the ore. The copper extraction and net acid consumption increased with increasing acid dosage. The copper extraction for acid curing with the addition of 6.2% water was higher than that without the addition of water due to the improved permeability and the increase in the contact with acid-soluble copper. During acid curing, the reaction of sulfuric acid with muscovite, abite and nacrite mainly took place on the surface of the particles while the reaction of sulfuric acid with clinochlore occurred not only on the surface but also inside the particles.

Jan 1, 2007

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By Emilie Williams

The Mouska Mine uses primarily shrinkage mining to extract the narrow veins that contain its mineralization. Mining is currently occurring on levels 12 to 14, reaching depths of 800 m below surface. Although the mine is not considered ?deep?, no backfill is available to fill empty stopes and certain areas remain open for over 500 m in height. As only narrow sill pillars remain to separate the levels, a highstress environment is created. Seismic activity was first observed when mining reached Level 11 (600 m deep) and has steadily increased since then. Seismic activity is associated with the highly-stressed sill and rib pillars; no geological structures have demonstrated significant seismic potential to date. In response to this increase in activity, pillar dimensions have been increased with depth and dynamic ground support has been installed. Seismic and pressure monitoring have been implemented, among other types of instrumentation. The following paper further describes the challenges associated with using conventional methods in the high-stress environment typical of the Canadian Shield, as well as several solutions implemented to mitigate these risks.

Feb 1, 2008

By A. J. Williams, W. H. A. Timm

"Lake Dufault Mines, Limited, is located north of Noranda, Quebec, and is a producer of copper and zinc concentrates. Various papers have been given on the mill design, construction and operation. 1, 2This paper is intended to describe the application of computer control to the Lake Dufault milling process. A brief history and description of the plant flowsheet will be given, followed by the reasons for installing the computer and the development of the program up to its present use. The success attained to date, comments on economic justification and future plans will also be given.HISTORY AND FLOWSHEETThe Lake Dufault ore body was discovered in September, 1961, and the mill commenced production during August, 1964. The rated capacity of 1,300 tons per day was reached by October 1, 1964. In milling the Lake Dufault ore, many metallurgical problems have been encountered, mainly due to wide and rapid variations in mill heads and oxidation of the massive sulphide ore. However, flexibility in plant layout and the incorporation of up-to-date instrumentation have facilitated its processing."

Jan 1, 1969