Search Documents

By Frank Baczek, R. Q. Honaker, D. P. Patil, B. K. Parekh

Fine refuse slurry impoundment is a requirement for the coal industry to dispose the fines. Impoundment maintenance is an on going problem for the coal industry and its breakage creates environmental as well as financial problems. Deep Cone thickener technology which has been successfully applied in the alumina industry to dewater red mud was evaluated for fine refuse slurry. Preliminary obtained in a pilot-plant test showed that properly flocculated conventional thickener underflow slurry could be thickened to about 52.5 wt % solids and could replace belt filter press. The Deep Cone thickener was also found to dewater clean coal slurry to about 70 wt % solids. Further testing of the unit at other coal preparation plant is in progress.

Jan 1, 2004

By F. F. Roberto

Sulfuric acid has been demonstrated to be an efficient lixiviant for in situ extraction of copper in the past. It has also been proposed that microbial production (by iron-oxidizing acidophilic bacteria) of acidic ferric solution either in situ or ex situ could provide an economic strategy to generate an effective lixiviant for secondary copper sulfides like chalcocite and covellite. Copper heap bioleaching also takes advantage of this approach. One of the major environmental challenges for in situ copper recovery projects is the containment of acidic solution within the ore deposit, and ultimate restoration of the depleted ore body to its original state. A perhaps overlooked aspect of projected site operations is the possibility that transient acidic conditions and pumping of solutions from surface reservoirs into the subsurface could stimulate the growth of iron- or sulfur-oxidizing species of acidophilic microbes in the ore body, leading to additional generation of sulfate, acid, and ferric iron. This outcome would benefit extraction of copper in mixed oxide/sulfide deposits in the near term, but could complicate restoration activities. Possible impacts of pumping acidic solutions into the subsurface on microbes resident in, or introduced into the extraction zone will be discussed in the context of our understanding of copper heap bioleaching and acid rock drainage. INTRODUCTION As high-grade deposits of metals such as copper continue to decline, conventional mining methods have evolved to mine and process larger and larger quantities of ore. What is currently defined as ore today often contains less metal than the tailings of past operations. The throughput of current-day mines also leads to tremendous amounts of waste rock and tailings that may threaten the environment and communities around the mines, as has recently been experienced by 3 major tailings disposal facility (TSF) dam failures in the past 5 years. Community acceptance of large mine operations thus becomes more difficult to achieve—loss of the social license to operate. In response, the mining industry urgently pursues innovations that can fundamentally change the way in which metals are mined. In situ recovery (ISR) of metals represents one approach to a more sustainable mining industry, by virtually eliminating the need for a pit or underground excavation, eliminating the excavation and transportation of ore to a process plant and the ensuing noise and dust that is generated, and any need for waste rock dumps or TSFs. An ISR mine could have very little visible footprint beyond a network of wells, pumps, and piping to transport pregnant solution to a recovery facility, such as a solvent extraction- electrowinning (SX-EW) plant for copper. Some solid waste streams and/or storage ponds may still be necessary to treat and store bleed streams, PLS and raffinate, or as part of groundwater restoration activities. Thus capital and operating investments would be potentially much lower than that required for a conventional mine. In theory production could also be controlled to adjust to subsurface ore grade and match market demand. A not insignificant challenge of in situ recovery is the requirement for an efficient, low-toxicity, and ideally selective lixiviant for the metal that is targeted.

Jan 1, 2019

By Michael J. Beare

Requirements of both local permitting and international fundraising are forcing increasing numbers of projects in Russia and CIS to carry out dual technical studies. The principal focus of Russian mining project design is to satisfy local regulatory requirements. However, the technical documents are not generally accepted by international banks for project finance outside Russia. Similarly, international study documents are not accepted for permitting in Russia. The purpose of this paper is to compare and contrast Russian and international approaches to mine technical studies and draw conclusions from this. The Russian design and permitting system is centered around two key statutory technical documents termed the TEO Konditsy and the TEO Project. These documents are subject to regulatory approval and are broadly equivalent to the international prefeasibility study and the feasibility study respectively. A comparison of study criteria suggests similar approaches are used for the main technical disciplines in project design by the time projects are at the point of construction, but there is divergence on environmental matters where the OVOS (Russian ESIA equivalent) differs from an ESIA in some significant areas. The key differences relate to project footprint, level of technical detailed required for baseline studies, level of public consultation, consideration and disclosure of information, labour, coverage of community and social issues and the preparation of a Social and Environmental Management System (SEMS). It has been noted that the Russian Design Institutes often leave the detailed economic analysis until after the TEO Konditsy. A common problem is design teams tend to look for ?technological solutions? without due concern for project economics. The end result of this can be mines that are overcapitalized and hence sub-optimal. It can be concluded that Design Institutes have the monopoly on Russian permitting reports and this is likely to continue. Similarly, Russian institutes generally do not prepare feasibility studies to international standards and this is likely to continue to be the case. Therefore to achieve the requirement of dual technical studies, the international consultants and Russian Design Institutes will need to cooperate on a joint work program. Key issues will be to ensure the most appropriate option studies are carried out at the right stages, that project economics are considered throughout the study, and that the environmental work program covers the additional studies necessary for the ESIA.

May 1, 2009

By G. W. H. Norman

Introduction During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in the mapping of major faults by using aeroplane photographs with a scale of about 1,000 feet to one inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately. The information regarding faults and structure is so widely scattered that it is difficult to obtain a clear picture of the essential features, either for planned prospecting or for analysis and development of ideas for further study. This paper, as originally conceived, was intended only to discuss and compare the regional structure of southern Abitibi county-where detail mapping and diamond drilling have been carried on intensively for the past ten years-and of the less well-known Chibougamau district, in order that the experience gained in the one area could be usefully applied in the other. However, a comparison of the two districts leads naturally to a consideration of their common relationship to certain major late-Precambrian structures that form an important northeast system across the southeastern part of the Canadian Shield.

Jan 1, 1946

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019

By T. Hadley, Northern Minerals Ltd, C. S. Griffith, T. A. Safinski, K. H. Soldenhoff, M. Fainerman-Melnikova, A. Manis

"ANSTO Minerals and Northern Minerals have been working together since 2012 on the process flowsheet development for the Browns Range project for the recovery of the heavy rare earths (Dy – Lu, + Y). Initial efforts were directed toward defining the most efficient and direct flowsheet for the Preliminary Feasibility Study (PFS), issued in June 2014, then towards the Definitive Feasibility Study (DFS), issued in February 2015. These goals were achieved by undertaking comprehensive laboratory and continuous piloting programs. Further improvements to the flowsheet following the DFS have been made. This publication provides an overview of the evolution of the process flowsheet based on these laboratory and piloting programs from the PFS through the DFS and beyond.INTRODUCTIONNorthern Minerals Ltd (Northern) has been working on developing their flagship project at Browns Range for the recovery of the heavy rare earth elements (HRE, Dy – Lu, + Y). The project is located in the north of Western Australia as shown in Figure 1. The Total Mineral Resource at the project is currently estimated at 8.98 Mt @ 0.63% total rare earth oxides (TREO) comprising 56,663 t of contained TREO using a cut-off grade of 0.15% TREO. Of the Total Mineral Resource, 58% is classified as Indicated Resource, with the remainder in the Inferred Resource category.The deposit is characterised by breccia-hosted, hydrothermal, HRE-rich, xenotime mineralisation. The main gangue mineral associated with the xenotime is quartz. The distribution of rare earths (RE) observed for the xenotime mineralisation at Browns Range is presented in Figure 2. Extensive test work has shown that the xenotime can be readily beneficiated to between 20 – 40% rare earth oxide (REO) using a process consisting of crushing and grinding, followed by magnetic separation and flotation steps. Continuous piloting of this process was conducted on ~80 t of trench-sourced ore in late 2013 at SGS Perth, to produce ~2 t of ~20% REO mineral concentrate (MC) for hydrometallurgical testing. The composition of the MC produced during piloting is presented in Table 1."

Jan 1, 2016

By Tony Lipiec, Ian Orford

"A key part of plant design is the selection of the design tonnage which is the hourly tonnage target that the equipment selection is based on. Its selection is critical for ensuring that the nominal tonnage which is critical to the financial performance of the project will be met. With deposits being developed at lower grades, higher tonnages and a higher degree of hardness variability, it is essential to ensure that the design process selects the comminution equipment which will be able to deal with the impact of this ore quality variation.Ore hardness and its variance are key factors to be taken into consideration for the selection of the design tonnage. It is well accepted that for the nominal or name plate tonnage to be consistently achieved, it is necessary to base the design tonnage on a hardness value greater than the average ore hardness of the deposit to be mined. The question is how much greater should this design value be to ensure that the nominal tonnage is met to the satisfaction of the project financial model. Standard industry practice is to set the design tonnage by:1. Select an ore hardness percentile that is greater than the average ore hardness to be the basis of the nominal tonnage. Typically either the 75th or 80th percentile value from the data set will be selected.2. Selection of a design factor to multiply by for determining the design tonnage, i.e. the design tonnage = tonnage (based on the average ore hardness) multiplied by design factor.This paper discusses the selection of the design ore hardness through the use of modelling or the use of a design factor. It further shows the impact of ore hardness variance on the capacity of the process and its ability to meet the nominal tonnage. Insight is provided as to what ore hardness percentile value should be selected balancing the shortfalls of tonnage for ores harder than the design value versus the above target production achieved for ores softer than the design ore hardness."

Jan 1, 2016

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By R. W. Brock

This subject is too broad and comprehensive to be dealt with adequately and authoritatively in this paper. It calls for the knowledge and experience of many men, but the results from such collaborative effort would be of great value, particularly if similar reports of the principal mining districts of the world were made on a standardized basis so that conditions everywhere might be directly and accurately compared. In considering conditions affecting mining in British Columbia, unfavourable as well as favourable factors must be taken into account. The unfavourable are apt to loom large and to be exaggerated rather than minimized; for it is human nature to see the blackness of the cloud rather than the silver lining; to think that one's own undertaking is beset with peculiar difficulties, and to attribute lack of greater success to out-side causes rather than to personal shortcomings. It should be recognized, however, that there is no country where the conditions for mining are ideal. The ideal mining country is the product of imagination, invested with every favourable condition found anywhere, but with none of the unfavourable conditions that are always present in reality. So if British Columbia has some handicaps to the industry, it is in good company. What is important is that the advantages compensate for the disadvantages, that the balance will compare favorably with that of competing states, for mining, like every other industry is competitive, and the cost of one's product must have a definite relationship to its price in the world's market.

Jan 1, 1924

By J. R. del Castillo, J. Ruiz, N. Kuyucak, J. Chavez

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11-km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River, which is located within the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (e.g., Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the "Technical Feasibility" phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralization/precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru S.A., and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the treated AMD could be used for supplementing the drinking water supply of Lima and for agricultural (e.g., irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for the implementation of the full-scale treatment facility to the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2004

By Don Peel, Jeremy Richards

Abstract - Aggregates (sand, gravel, and crushed stone) are low unit-cost products extracted in very large volumes for the construction of buildings, roads, and other infrastructure essential to modern society. Because of their low unit value, transportation costs are a key factor in resource economics, and deposits are commonly developed close to market (i.e., close to towns and cities, or along low-cost transportation corridors). This proximity results in potential conflict with residents over land use, disturbance, and pollution. Management of aggregate resources in Alberta is examined in the light of resource geology and distribution, and governance. A case history of development of the Calahoo-Villeneuve deposit is described, and the conflicts between residents and developers that led to establishment of an Area Structure Plan (ASP) are explored. The plan sets limits to, but at the same time safeguards, resource extraction, and defines terms for compensation to residents through a voluntary levy on production (Community Enhancement Fund). This fund is used to support community activities and to pay for a groundwater monitoring program. The ASP is examined within the context of the "Seven Questions to Sustainability" as set out by Mining,Minerals and Sustainable Development-North America (2002). It is concluded that the ASP, for the most part, provides a good model for conflict resolution and sustainable resource development, which could usefully be applied in other jurisdictions. The ASP was developed at a municipal level, and adoption at a provincial level would aid sustainable development of aggregate resources across the province.

Jan 1, 2003

By J. Schnarr, D. Deever, E. Johnson

"The above committee sent out a questionnaire to the gold mines for the purpose of learning what units and methods are currently in use in the mines as the first step in an attempt to agree on standard units to be used in any papers or reports that may be given to other mines or presented at meetings. The next step is to try to arrive at acceptable standard units for reporting and methods of making tests. It was suggested by Mr. J. Jardine of Eldorado Mining and Refining that the use of the metric system should be seriously considered. It was also brought out that there was no intention of having any mine change their methods to the standard for internal reporting as this would involve too much change. However for external reporting there shouldn't be too much difficulty in converting to the accepted standard units.On the following pages are the reports of those mines that replied to the questionnaire.MALARTIC GOLD FIELDS LIMITEDP.A. Coulter1. All assays - Ounces per ton2. Consumption of reagents - Pounds per ton3. Reagent strength of solutions - Pounds per ton4. Reducing Power - As described in C 0 I.L, Analysis of Cyanide Solutions5. Pulp Densities - Grams per litre6. Screen Analysis (Tailings) A sample of 150 gms is washed on a 200 mesh screen. The plus 200 mesh material is dried and ro-tapped for fifteen minutes. The plus 200 mesh portions are weighed cumulatively (the balance is considered -200 mesh) and reported in per cent."

Jan 1, 1967

By Leibniz University, D. Zapf

"The demand for gas storage operations with high withdrawal rates and operation modes different to a seasonal storage regime requires a more detailed rock mechanical consideration of thermal induced stresses in the vicinity of the caverns. This means that the change of gas temperatures during operation and the consequences of these temperature changes on the stressing of the salt rock mass must be taken into account in the rock mechanical dimensioning. Within the rock mechanical calculations a loading history, i.e. a pressure versus time dependency, has to be defined. As rock salt has a time dependent material behavior stress redistributions in the rock salt mass take place even under constant internal pressure conditions. Therefore not only withdrawal and filling periods but also the duration of phases with nearly constant internal pressure is significant for the resulting state variables. Within the paper the differences and consequences for the rock mechanical recommendations are discussed. As a result it can be concluded that recommendations with respect to minimum operation pressure as well as for maximum withdrawal rates can be answered only in connection with the respective time intervals."

Jan 1, 2015

By N. Hiroyoshi

In the leaching of chalcopyrite with sulfuric acid solutions, the copper extraction rate reaches a maximum at a given redox potential. This article reviews our studies on the determination of the optimum redox potential for chalcopyrite leaching. Shaking flask and column leaching experiments for a chalcopyrite concentrate were performed under various conditions, and the results were analyzed using a normalized redox potential defined from a reaction model assuming the formation of an intermediate CU2S from chalcopyrite. Factors, such as metal ion concentrations, solid/liquid ratio, and presence of iron-oxidizing bacteria, caused significant variations in the copper extraction versus time plots. However the copper extraction rate versus normalized redox potential plots were independent of the above factors and the copper extraction rate reached a maximum at the normalized redox potentials around 0.43. Converting the normalized redox potential to the solution redox potential gives the optimum redox potential for chalcopyrite leaching as a function of cupric and ferrous ion concentrations. This semi-empirical equation can be used to predict the optimum redox potential during leaching operation, and is useful to design the redox-controlled heap leaching for chalcopyrite.

Jan 1, 2007

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By Frands Jensen, Erik Eriksson

"Haldor Topsoe’s Wet gas Sulfuric Acid (WSA) technology has been proven in a number of industries converting sulfurous gasses to concentrated sulfuric acid. In the metallurgical sector plants have been delivered handling SO2 gasses from copper, zinc, molybdenum, and lead ore. WSA has high energy efficiency and allows autothermal operation from feed gas strengths as low as 3.0% (volume). Recent variants of the WSA process have been developed that allow very high SO2 conversion efficiencies of over 99.9%. This paper describes the technology, its advantages and industrial achievements.The WSA technology is well suited for production of concentrated sulfuric acid of commercial quality from the sulfur dioxide (SO2) gas that inevitably emerges from the metallurgical processes. Some of the features that make the WSA technology attractive for this application are:- High SO2 conversion rates (up to 99.99%)- High energy efficiency leading to a low autothermal point (~ 3% SO2)- No need for gas cooling and drying to produce concentrated sulfuric acid- No production of waste- Very low cooling water consumptionThis paper describes the WSA process principles and highlights features that make this process attractive for handling SO2 gases."

Jan 1, 2014

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By B. Stuckert, P. Sheehan, J. Balfour, B. (Manas) Das, D. Fawcett

"With the growth of large scale surface mining operations, waste disposal and stability of waste dumps pose a challenging problem to engineers. Vibrations due to blasting operations proximal to these dumps further complicates dump design. Many dumps which are statically stable may become unstable due to the effects of blasting vibrations.A joint project between CANMET and Smoky River Coal Ltd. has been initiated to study the dynamic stability of waste dumps. The study involves development of an analytical algorithm combined with field monitoring to assess dump performance.Another objective of the study is to provide baseline data for a vibration attentuation relationships for sedimentary rock (coal) environments: most studies to date are for base metal mines. The effect of dump thickness on vibration response is also addressed.The key objective of the study is to present a methodology for assessing the dynamic stability of waste dumps. Implicit in this methodology are a number of assumptions concerning vibration attenuation in sedimentary rock environments, and response of the dump material to induced vibration. Where possible, these assumptions have been compared with monitoring data as a check on their validity."

Jan 1, 1989

In this paper, the use of electrochemical AC impedance spectroscopy (EIS) for in-situ diagnosis of high temperature PEM fuel cells is described. EIS was performed on single cell hardware, built in-house, using a fuel cell test station modified to operate up to 120°C and 30 psig. Electrode kinetics, membrane resistance, porous-layer and mass transport impedance of MEAs, assembled in-house, were measured at various current densities for the purpose of validating the test station and cell hardware, and for optimizing MEA and flow-field designs. The effect of temperature and humidity on the various impedances was investigated. Impedances obtained at lower and higher temperatures were compared to obtain insight into the issue of water management in operating fuel cells.

Jan 1, 2005

By Mario A. Morin

The last few years have seen considerable consolidation of the mining software industry and a trend towards greater planning and production control system integration, particularly for surface mines. The mining industry is starting to realize the benefits of system integration and will continue to drive the evolutions of these systems. Several trends can now be observed. The trends include application and system integration, data portability, ?intelligent? systems for support of decision-making activities, mine process-control and automation. While many planning systems are moving in this direction, there is room for considerable improvements. This paper will discuss these trends, examine the current state-of-the-art in mine design software, and identify areas where improvements should be made and why.

May 1, 2004