Search Documents

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By Alim Ullah

Danieli entered into the Direct Reduction (DR) field in order to offer its clients complete turnkey facilities for steelmaking?from processing of raw materials through finished products. The Danarex® Process produces a passivated product, called the Supermetallic (SPM), without hot-briquetting. One of the main features of the Danarex® Process is its ability to produce approximately 50% of the Direct Reduced Iron (DRI) through reduction gas generated in a reformer and another 50% through recycling preheated furnace exit gas. Some other distinguishing features are: separation of carburising and cooling zones and the use of double bustle for better distribution of gas inside the shaft furnace. A pilot plant was set up at Hazen Research, Inc., Golden, CO in order to show that the integrated process works as expected and to obtain process data. The SPM obtained was of a very high quality, evidenced by metallization levels of 92% to 98%. The carbon content could be controlled between 1.5% to 4.0% by varying the operating conditions and approximately 75% of this carbon was present as Fe3C. The product was tested for inertness by Chilworth Technology, England, using UN standard tests and was found to be safe for outdoor storage and transportation.

May 1, 2003

By J. Y. Kim

This paper presents a novel action recognition method for observing human workers using interactions between actions and related objects on an internal construction site. This method can be used to measure work rates for labour productivity monitoring. This monitoring is critical because the performance of a construction project is significantly impacted by labour productivity. However, construction sites are generally crowded with a large number of workers and objects. Such congestion disrupts the accurate, automatic recognition of construction workers? actions. This congestion is one reason that existing automatic action recognition studies of construction areas mainly focus on workers? actions themselves. However, the crowded conditions mean that sites could offer a great deal of clues that could be used for automatic action recognition. According to psychological studies, interactions clearly take place between human actions and related objects, such as between hammering and a hammer. Humans use these interactions to recognize actions or objects more accurately. On the construction site, workers, materials, tools, and equipment are carefully planned out ahead of actual construction. The categories of workers and objects are pre-defined and, as noted, specific interactions define relations between worker actions and objects. In this paper, the interactions are limited to human workers and their hand-held objects. Action recognition results can be combined with hand-held object information to improve recognition accuracy. With the limited interactions, experiments in this paper show a significant improvement in action recognition. This paper describes the utilization of these interactions to improve construction action recognition accuracy based on human skeleton data and 2D color video from Microsoft KINECT sensor.

Aug 1, 2013

By T. -W. Hong, Y. Son, S. -J. Hong, D. Choi

The characteristics of indium-tin-oxide (ITO) nanoparticles recovered from TFT-LCD panel scraps were investigated. The ITO was separated from TFT-LCD panel scraps by dissolving the color filter layer located between the ITO layer and the glass substrate. The solution was filtered to separate the ITO from the color filter component, and the filtered ITO was dissolved in the acid solution. ITO nanoparticles were then precipitated with ammonium hydroxide and organic dispersing agent, followed by heat-treatment at 600 °C. HRTEM, EDX and XRD analyses revealed that the 20 nm sized particle were composed of 90 % In and 10 % Sn, and were well crystallized to in the (222) preferred orientation.

Jan 1, 2014

By Z. Zhao, B. Li

"Fractures are the key channels for fluid flow and mass transport in fractured rocks of low/negligible matrix permeability. In single rock fractures, surface roughness causes fluid flow in tortuous paths, and reduces the overall fracture conductance. A number of empirical models have been proposed to relate the reduced hydraulic aperture to the mechanical aperture due to surface roughness, which were revisited and compared. Using two of those relationships between hydraulic apertures and mechanical apertures, we studied the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks. The results show that fracture roughness can affect the flow rates and residence time to varying extent, mainly depending on the empirical models between hydraulic apertures and mechanical apertures. However, fracture roughness has negligible influences on the general patterns of fluid flow (channeling) and solute migration (e.g., travel paths and shape of breakthrough curves). This is because the connectivity of a fracture network is mainly determined by other geometrical parameters (fracture positions, orientations, and lengths), rather than roughness or apertures. INTRODUCTIONIn fractured crystalline rocks of low or negligible matrix permeability, fluid flow and contaminant migration mainly occur within the connected fractures. An understanding of fluid flow and contaminant migration in fractured rocks is a crucial issue in many deep underground projects, e.g. underground repositories for radioactive waste, CO2 sequestration, enhanced geothermal systems, oil and gas production, etc. Rock fractures are typically rough-walled, and surface roughness appears to have first order control on the mechanical and hydraulic behavior of single rock fractures (Boutt et al., 2006).It is well known that the mechanical aperture of a rock fracture is usually larger than its hydraulic aperture, due to fracture surface roughness (Tsang and Witherspoon, 1983). However, for naturally fractured rocks including numerous discontinuities, the effects of this reduced hydraulic aperture in local fractures on macroscopic fluid flow and solute transport in complex fracture systems still remain unclear. Many previous studies assumed identical hydraulic and mechanical apertures in discrete fracture network models for simplicity (Min et al., 2004; Zhao et al., 2011). Therefore, the main objective of this study is to evaluate the influences of local surface roughness of fractures on fluid flow and solute transport processes at the macroscopic scales of fracture networks, by employing the empirical models that relate the hydraulic aperture to the mechanical aperture."

Jan 1, 2015

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

By J. Groppo, W. Zhang, R. Honaker

"The flotation of monazite is depressed when using hydroxamic acid as a collector in the presence of calcium ions which may exist due to the dissolution of minerals such as calcite. Minor dosages of sodium hexametaphosphate (SHMP) were found to effectively depress calcite, whereas the flotation of monazite was not impaired in single mineral flotation tests. However, in a mixed mineral flotation system, monazite flotation was depressed significantly. The mechanism of hydroxamate adsorption on monazite and calcite, the depression mechanism of calcite on monazite, as well as the depression mechanism of SHMP on calcite and monazite were studied using micro-flotation, electro-kinetic, and adsorption tests. Findings indicate that the adsorption of hydroxamate on monazite was due to chemisorption while adsorption on calcite was a result of physical interaction. SHMP significantly increased the negative charges of calcite surfaces which depressed the adsorption of the hydroxamate anions on the calcite surfaces due to an elevated electrostatic repulsion force. When calcium-rich minerals such as calcite are mixed with monazite, the calcium ions dissolved from the mineral surfaces specifically adsorb onto the phosphate oxygen sites on the monazite mineral surfaces thereby causing depressing effects. The addition of SHMP to suppress collector adsorption on the calcite surfaces interacts with the calcium species that were specifically adsorbed onto the monazite surface, which prevents hydroxamic acid adsorption onto the rare earth oxygen sites due steric hindrance and results in the flotation depression of monazite. INTRODUCTIONAs one of the commercial rare earth ores, monazite has been widely exploited to produce additives for catalysts, batteries, alloys, etc. Because of the complexity and the fine nature of some monazite ores, methods such as gravity, magnetic, and electrostatic separation to treat beach sand monazite fail to produce satisfactory concentrates, suggesting the use of floatation is warranted (Cheng, Holtham, & Tran, 1993). The primary associated minerals of monazite ores include ilmenite, quartz, zircon, rutile, sillimanite (Dixit & Biswas, 1969; Pavez a& Peres, 1994, 1993). Using sodium oleate as collector for monazite has been reported in many studies (Cheng et al., 1993; Dixit & Biswas, 1969; Pavez & Peres, 1994, 1993). Several investigations have reported maximum floatability of monazite occurring at pH values between 8 and 9 (Cheng et al., 1993; Dixit & Biswas, 1969). A study conducted by Pavez and Peres (1994) compared the use of hydroxamate and sodium oleate for the treatment of a monazite ore and found that hydroxamate significantly improved the grade of rougher concentrate."

Jan 1, 2016

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013

By O. A. Ojo, R. G. Ding, M. C. Chaturvedi

In this study, the fusion zone microstructure of tungsten inert gas weld of a directionally solidified NhAl-base alloy was examined by the standard metallographic techniques involving the use of optical, analytical scanning and transmission electron microscopes equipped with energy dispersive spectrometer. Fusion zone cracking was observed to be closely associated with interdendritic secondary solidification microconstituents identified as consisting of y, y&apos; and NiMo (Y) phases. Depression of solidification temperature to the terminal ternary eutectic reaction temperature of the system during cooling is suggested as an important factor contributing to the fusion zone cracking.

Jan 1, 2006

By Blair Hrabi

Introduction; ?Risks Associated with the Resource Estimation Process; ?Limitations of Available Data; ?Geological and Structural Control of Mineralization Trends; ?Recognizing Multiple Mineralization Controls and Complex Trends; ?Accurate Geodomaining; ?Conclusions.

May 1, 2013

By D. D. Campbell

"The Port Radium mine of Eldorado Mining and Refining Limited lies on the western tip of a large peninsula midway up the east shore of McTavish Arm, Great Bear Lake, about 30 miles south of the Arctic Circle. The mine is serviced by air, 950 miles from Edmonton, and by water, 1,380 miles from Waterways, Alberta.The veins were found, and the copper and cobalt minerals in them reported, by J. MacJntosh Bell of the Geological Survey of Canada in 1899. The veins were investigated by Gilbert Labine and E. C. St. Paul in 1930, and as a result of their work the Eldorado mine was brought into production in 1934. It produced silver and radium ores until 1940, at which time, as the silver orebodies had been mined out and the market for radium was negligible, it closed down. Early in World War II the need for uranium for the Manhattan Project was emphasized, and the mine was reopened in 1942. As a security measure Eldorado Mining and Refining was created a Crown company in 1944. The Port Radium mine has continued to be one of Canada's principal producers of pitchblende concentrates, and to date has about 25 miles of underground workings developed on fourteen levels.Regional GeologyThe general geology of the McTavish Arm area was mapped by D. F. Kidd in 1932 on a scale of one inch to four miles. A great deal of more detailed work has since been done by geologists of the Geological Survey and of Eldorado. The entire area at the end of McTavish Arm lies within the Precambrian Shield immediately east of its western margin. Most of the area is underlain by granitic masses which have intruded a sequence of late Precambrian sediments, volcanics, and hypabyssal intrusives. The pre-granite rocks now occur in extensive, irregular patches and pendants within the granite. Pitchblende deposits have been found in the district in all rock types, but the most favourable host rocks are the cherty sediments of the lower Echo Bay group."

Jan 1, 1949

By S. Razavialavi

In the planning phase of every construction project, layout of temporary facilities is a crucial task; site layout can affect safety, travel cost and time, construction productivity, and space utilization. However, site layout planning can be a complicated problem, due to the interdependency of influencing factors. Although interaction among activities is one of the major drivers of site layout planning, it has not been properly addressed in past research. In this study, simulation is presented as a promising tool to address this gap. The capability of simulation technology to model complex processes in construction projects makes use of simulation tools in site layout optimization problems effective, while existing methods are unable to perfectly model these problems, in some cases. Additionally, the advantages and challenges of implementing simulation are assessed and a generic framework for simulation application in site layout planning is proposed.

Aug 1, 2013

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

By D. K. Sarkar, Ying Huang

"Superhydrophobic thin films were fabricated on aluminum alloy substrates by chemical etching followed by passivation with organic acid molecules; (ii) electrophoretic deposition (EPD) of functionalized ZnO nanoparticles and (iii) electrodeposition of organic-inorganic composite materials. The physical and compositional analyses of the deposited thin films were characterized by SEM, FTIR, XRD as well as contact angle goniometer. The contact angle and surface roughness of the superhydrophobic surfaces prepared by the chemical etching process were found to be 156° and 2.29 µm, (ii) by the EPD process were found to be 155° and 4.54 µm and (iii) by the electrodeposition process were found to be 159° and 7.11 µm, respectively.The corrosion properties were analyzed with both polarization and electrochemical impedance spectroscopy (EIS) in NaCl aqueous solutions. The results demonstrate that the superhydrophobic thin films on aluminum alloy substrates display better anti-corrosion behavior than the as-received aluminum substrate. The comparison of results pertaining to the compositional and corrosion properties of these thin films on aluminum will be discussed in this work.INTRODUCTIONSuperhydrophobicity is defined as a surface property which provides non-wetting characteristics with a water contact angle larger than 150°. It is observed that the creation of certain micro-nanoroughness structures promotes the entrapment of air in the spaces of the rough surface morphology. In addition, lowering the surface energy helps to reduce the affinity of water drops to the surface, thereby weakening the water-surface interaction. Recently, various fabrication methods for superhydrophobic surfaces have been explored (Sarkar, 2010, Huang, 2010, 2011, 2013, 2015a, 2015b), such as the sol-gel process (Brassard, 2011), plasma treatment (Marchand, 2013), chemical vapor deposition (Zheng, 2009), chemical etching (Saleema, 2011), electrodeposition (Ying, 2011) and electrophoretic deposition (EPD; Huang et al., 2015b)."

Jan 1, 2016

By Arnold R. Miller

Overview ? Vehicle Projects LLC (prime contractor) and the Fuelcell Propulsion Institute have developed the world?s first fuelcell locomotive. ? Principal applications are underground mining and tunneling. ? Because fuelcell vehicles solve the problem of underground emissions, mining is expected to be their first commercially viable market. ? The first year of a three-year project to develop a fuelcell mine loader is funded and underway.

May 1, 2002

By P. Van Marcke, X. Sillen, G. J. Chen, I. Troullinos, A. Dizier, J. Leysens, X. L. Li, J. Verstricht

"In Belgium, Boom Clay is considered as one of the potential host formations for the disposal of the High Level radioactive Waste (HLW). The URL HADES at 223 m depth at Mol site was constructed in order to study the feasibility of HLW disposal in Boom Clay. Since 1995, the URL R&D programme has focused on large scale demonstration tests like the PRACLAY experiment.The PRACLAY in-situ experiments include a set of three tests: The gallery and crossing test, PRACLAY Heater test and PRACLAY seal test. The main aim of the Heater test is to study at a large scale the thermal impact of a HLW repository on the host rock. The test is housed in the PRACLAY gallery. A hydraulic seal, made of compacted swelling and low permeable bentonite annular ring was installed at the intersection between the heated and the non-heated part of the gallery. The primary objective of the seal is to provide undrained hydraulic boundary conditions for the Heater Test.The PRACLAY gallery was constructed in 2007 and the hydraulic seal was installed in 2010. The bentonite is hydrated by natural and artificial process. The swelling, total pressure and pore pressure of the bentonite are continuously measured and analysed by numerical simulations to get a better understanding of this hydration processes. The performance of the seal is tested systematically by means of gas injection breakthrough tests and permeability tests at interface bentonite / Boom Clay and in the Boom Clay around the seal.The PRACLAY Heater will be turned on at the end of Oct. 2014, since a sufficient seal swelling has been attained to fulfill its role for the PRACLAY Heater test. This paper will focus on the PRACLAY Seal test: How we understand the process behind the hydration of the bentonite and how we test the performance of the bentonite seal."

Jan 1, 2015

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007

By David Stone

The Beal Mountain Mine near Anaconda, MT is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of about 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges.

May 1, 2001