Search Documents

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation on a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled -both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form as is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation ?On a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By Fathi Habashi, Ernesto Bourricaudy, Fouad Kamaleddine

Ilmenite occurs in black sand at the mouth of great rivers as in India, or as massive deposits like in Quebec Province in Canada. It is unsuitable for processing into pigment or for metal production because of its high iron content and its low grade. Pyrometallurgical and hydrometallurgical methods have been developed to cope with this problem which resulted in the production of two commercial products that became known as synthetic rutile and Sorelslag. Attempts are also underway to produce TiO2 pigment directly from ilmenite. This report presents a newly developed process called the Magpie process, which enables the production of high-grade synthetic rutile (over 95% TiO2) from low grade ilmenite (10-12% TiO2). Naturally, if such process is applied for low-grade ore it can be applied with advantage to high grade material as well.

Jan 1, 2014

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By S. Kelebek, Gerhard W. Heinrich, Peter F. Wells

"The review and optimization of process stages is an integral part of the program to improve the metallurgical performance of the Strathcona Mill. Improved primary grind size distributions, streamlining of rougher-scavenger circuits and increased platinum recoveries were the target of plant and laboratory scale tests. The results can be summarized as follows:• Decreasing the primary grinding cyclone vortex finder diameter for nickel/copper ore gave significant increases in overall copper recovery and improved rougher flotation selectivity.• The scavenger flotation stage in the circuit treating copper ore was found to contribute little to this circuit's copper recoveries -yet to be essential for acceptable recoveries of nickel, platinum and gold. The elimination of this stage by re-routing the tailings from the copper ore rougher into the nickel/copper ore rougher feed has lead to lower gangue recoveries to the nickel concentrate and to improved copper-nickel separation, while reducing equipment operating costs.• Surface aging effects such as oxidation are known to decrease flotation recoveries of platinum minerals such as sperrylite. The conditioning of an intermediate non-magnetic process stream with copper sulphate prior to thickening increased the platinum recoveries in the subsequent flotation stage by approximately 10%."

Jan 1, 1996

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By M. Choy, A. Kadiayi, E. Magdzinski

"Design of engineering controls to limit occupational noise exposure rely on accurate calculation inputs. Sound in mines can carry considerable distances. Mine ventilation engineers rely on noise propagation calculations to estimate silencer performance criteria for key mine fan installations that are often in proximity to occupied areas of a mine and can remain in service for decades. The blasted and rockbolted walls of hard rock mining tunnels have unique acoustical properties. Underground testing in an operating metal mine in Sudbury, Canada was performed and results processed to characterize noise propagation in mines, with the goal of improving the accuracy of noise calculations.INTRODUCTIONAs mine operators continue to improve and promote workplace safety, addressing noise at fixed infrastructure locations is observed as increasingly common. Underground fans are important to consider in this context, as they are typically loud, in proximity to occupied and sensitive workplaces, and operate nearly continuously. Predicting noise propagation from ventilation fans within underground mines has long been a challenge, with few available resources documenting acoustical properties as calculation inputs. Other factors in addition to rock face absorption properties include tunnel geometry and distance from the fan, which play critical roles in characterizing the noise level at any given point away from the fan. By understanding and establishing methods to better predict noise dissipation along underground mining tunnels, engineers can design noise controls with a greater degree of precision and confidence to effectively protect workers from over exposure to noise.This paper investigates classical methods of predicting reverberant room and direct field noise propagation. These prediction methods are then compared to noise measurements taken within the Fraser Mine of Glencore’s Sudbury Integrated Nickel Operations (Sudbury INO) Measurements were taken at a depth of ~881 m (2,889 ft), along an ~300 m (984 ft) long blasted hard rock mining tunnel. The noise along the mine tunnel resulted from the intakes of two 900 kW (1,200 hp) ventilation fans with a combined exhaust capacity of 300 m3/s (630,000 cfm)."

Jan 1, 2019

By Craig Haase

A. Introduction

Jan 1, 2003

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By L. Dufourm

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015

By H. Alzraiee

Traditional planning methods such as CPM and PERT have been useful tools to manage construction projects. However, the underlying model of these traditional methods often seems to fail to represent real projects as they tend to assume no interrelationship between project components. In reality, project components have complex dynamic feedback process that requires modeling of inherent uncertainty in the execution of these projects. Nevertheless, this dynamic nature and uncertainty have not been explicitly addressed by traditional planning methods. Project failure can be attributed to poor representation of the inner and outer aspects of operations that are responsible for project dynamics. Uncontrollable external forces are often cited but the real cause may be internal such as the feedback process among components of the project. An alternative perspective is offered in this paper through system dynamics (SD) that accounts for the feedback process and discrete event simulation (DES) for modeling the uncertainty. The proposed method utilizes SD method for modeling project dynamics and DES method coupled with CPM network for operational details and uncertainty, respectively. A case study that involves preparing engineering drawings in a design office is used to demonstrate the use of the developed method and to highlight its capabilities. Modeling the dynamic dimension is expected to enhance planning and scheduling of construction operations and to provide a better understanding of the impact of various internal and external factors on project schedule and productivity performance.

Aug 1, 2013

By G. R. Guillet

Salt is restricted to five major beds in south western Ontario, totalling as much as 200 m in thickness. These beds are located at depths ranging from 270 m to 750 m below the surface, fringing Lake Huron and the Detroit River from Windsor to Kincardine, and extending inland as far as London. Manitoulin Island, the Bruce Peninsula and the north part of the Niagara Escarpment form the northeastern rim of the Michigan Basin, a major structural depression in which the salt was deposited 400 million years ago when much of North America was covered by the Silurian sea. Salt is mined underground at Windsor and Goderich; it is also brought to surface as brine through deep wells at Windsor, Samia and Goderich. Artificially- created caverns in salt beds are extensively used for storage of liquid hydrocarbons at Windsor and Samia.

Jan 1, 1984

By Y. Mitani, H. Ikemi, K. Kitamura, H. Honda

"Instead of carbon capture and geological storage (CCS) that does not rely on structural aquifers, injecting carbon dioxide into sedimentary rock deep underground has been considered. For advection velocity of the fluid is slow, the permeability of sedimentary rock deep underground is low. In order to perform the CCS on the low permeable sedimentary rock, it is necessary to clarify the behavior of long term storage properties of carbon dioxide (CO2).In this study, the permeability and storativity of CO2 injected into low permeable rock has been evaluated. The injection of supercritical CO2 has been conducted on the specimen of Ainoura sandstone (unit weight: 2.39 g/cm3, porosity: 11.9 %) saturated with water by using flow pump method. The experiment has been set up to reproduce the similar condition of deep underground reservoir under 20 MPa confining pressure, 10 MPa pore pressure, 35°C temperature and 3 µl/min CO2 injection rate. In order to prevent an increase in pore pressure, the boundary condition on the outlet side of specimen has been kept a constant pressure.As a result, it has been possible to observe step by step the change of the differential pressure between both ends of specimen. Furthermore, the relative permeability and specific storage of rock under supercritical CO2 injection has been examined by the theoretical analysis of flow pump permeability test incorporating Darcy’s law for two-phase flow. It is observed that CO2 has been transmitted gradually while CO2 stored in the rock. It is also clarified that residual water has existed in specimen after showing the constant differential pressure in the end of the experiment. Using the results of the experiment, 3D core-scale flow-simulation by using TOUGH2 has been conducted due to confirm the flow of fluid and CO2 distribution in the specimen. From the experimental results and analytical solution to them, permeability and storativity are identified, and simulation results support the validity of the experimental results."

Jan 1, 2015

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By J. F. Vynne

ABSTRACT This paper examines several of the systems and processes that have been developed over the past few years and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline rated suspended loads (RSLs) and inspection and response strategies. The use of these technologies provides significant increases in dragline production and reduces maintenance costs, downtime and the chance of a catastrophic failure.

Jan 1, 2010