Search Documents

Inco Limited has been evaluating options for streamlining the overall flowsheet at its Sudbury, Ontario operations to improve productivity and to minimize the cost of at¬mospheric emissions reduction. Some of the flowsheets being considered include vari¬ous levels of copper/nickel separation at the Clarabelle Mill where all Inco's Sudbury Basin ores are processed. This paper reports on the laboratory and miniplant studies car¬ried out during the flowsheet development for a commercial Cu/Ni separation plant. There are two potential feed streams for Cu/Ni separation. It was determined that Cu/Ni separation from the rougher concentrate requires no regrind, and a very clean copper concentrate is produced, but the recovery of copper is limited to about 70% from ore. Cu/Ni separation is more difficult from the bulk concentrate because of the presence of excess flotation reagents in the slurry and due to locked particles. By replacing the slurry water with clean process water, and by addition of some hydrogen peroxide, entrainment is minimized and excess reagents are removed from the surface, providing a satisfactory separation of copper from nickel. Fine regrinding is required to increase liberation of the locked particles and to obtain 85% copper recovery with minimal nickel contamination of the concentrate.

Jan 1, 2005

By Hasini Wijayaratne

Anode cover material, a mixture of crushed electrolyte and alumina, is a crucial part of an aluminium reduction cell because of its important role in maintaining overall heat balance. However, until recently little attention has been given to understanding or controlling its composition and quality. The thermal conductivity of anode cover material determines the extent of the heat loss from the top of the cell. This will change as a function of the granulometry and composition of the applied cover as well as over time as the cover material consolidates on top of the cell. The ability to measure or predict the thermal conductivity of fresh and ageing cover is an important tool for managing cell heat balance. Recent studies have shown that granulometry or more correctly, voidage is likely to be the predominant determinant of thermal conductivity of anode cover materials. We have developed equipment to measure the thermal conductivity of granular cover material and tested the relative importance of composition (ratio of alumina to crushed electrolyte) and granulometry/voidage on cover thermal conductivity. In general, our results confirm that granulometry is the dominating factor. Generally, high voidages contribute to lowering the thermal conductivity especially when particles are mostly fine. However the relationships between granulometry, voidage and thermal conductivity are complex due to the varying nature of heat transfer between particles. Aging of granular cover material occur during cell operation forming a consolidated crust due to exposure to heat and fumes over time. Structure and thermal behaviour of this consolidated crust is also important in understanding the overall properties of cover. This paper presents the outcomes of laboratory studies conducted in order to understand the thermochemical behaviour of anode cover material and in particular, the role of fines in anode covers mixtures.

Jan 1, 2011

By C. Han, S. J. Zhou, Y. B. Shen, D. Z. Wei, P. Fang

"Collecting property of two hydroxamic acid collectors have different type of nonpolar structure to hemimorphite has been comparatively studied via monomineral flotation test, and the reason causes different collecting performance has been discussed from the view of relationship between molecular structure and collecting property. The flotation tests results show that C5-9 hydroxamic acid has an unbranched linear alkyl nonpolar group shows better collecting property to hemimorphite than cyclohexyl hydroxamic acid which has a naphthenic nonpolar group. FTIR detecting results show that the adsorption type of collector adsorbed on hemimorphite surface is chemical adsorption. Calculation results of polar group’s geometric structure parameters, polar group’s electron density distribution, octanol-water partition coefficient (logP) and molecular frontier orbital energy show that the key factor caused different collecting property of two collectors to hemimorphite is the logP; unbranched linear alkyl nonpolar group is more conducive than naphthenic nonpolar group to make hemimorphite particle more hydrophobic.INTRODUCTIONZinc-bearing mineral recovered from lead-zinc ores is the main source that people can obtain zinc resource from nature. However, natural sulfide ores are currently getting depleted steadily for the primary zinc source. In order to satisfy the future demand of zinc resource, there is an obvious recognition that the recovery of zinc oxidized minerals from the ores is a crucial alternative (Hosseini & Forssberg, 2007; Navidi Kashani & Rashchi, 2008).But the fact that can’t be ignored is the flotation of zinc oxidized minerals is much more difficult than that of zinc sulfide minerals, which is mainly due to the flotation characteristics of these zinc oxidized minerals such as lower selectivity and higher reagent consumption, as well as complex and variety of lead-zinc ores. Presently, there have been many various beneficiation technologies used for recovering zinc oxidized minerals and dealing with ores for recovering metallic zinc such as flotation and hydrometallurgy (Abkhoshk, Jorjani, Al-Harahsheh, Rashchi, & Naazeri, 2014; Önal et al., 2005). But from an overall perspective, flotation is the most common method used for the beneficiation of zinc oxidized minerals, and there have been extensive investigations conducted on the flotation of zinc oxide ores (Ejtemaei, Gharabaghi, & Irannajad, 2014). Until now, the most well-known method used commercially for the flotation of zinc oxidized minerals is sulfidization with sodium sulfide and flotation with a cationic collector of amines containing from 8 to 18 carbon atoms. However, a major problem for this method is the large amount of fines and slime results in the increase of reagent consumption and promotes the phenomenon of slime-coating. For preclude this negative effect, the de-sliming and processing optimization is indispensible (Peres, Borges, & Galery, 1994; Salum, de Araujo, & Peres, 1992)."

Jan 1, 2016

By Gino Palarchio

Dofasco is Canada?s 2nd largest steel manufacturer producing 4.5 million tons of flat rolled steel per year. They have revenues of over $3 billion and employ 7,000 people in their Hamilton, ON plant. Dofasco is North America?s most profitable steel producer and were recently ranked as the #1 steel maker in the world by Dow Jones. Motivation to Improve In the 1980?s the steel business was good. However, in the late 80?s and early 90?s things began to change. Globalization was beginning to influence the market, imports started arriving at lower prices and higher quality, hangover from the 1970?s inflation saw costs rising and prices dropping, there was a shift from a sellers to a buyers market, and shareholder returns were beginning to erode. Dofasco took a step back and evaluated their maintenance performance and found that they were operating in an environment where 70% of their work was reactive and only 30% was proactive. They also found that the rate of product quality improvement was flat and their average equipment availability was only 78%. At that point they realized that Equipment Reliability was key to improving product quality, production output, costs and shareholder return. They initiated a project to research, develop, and implement the most advanced maintenance practices and information technologies to achieve maximum equipment reliability.

May 1, 2001

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By G. J. Hamilton

"THE Royalite-Canada Southern Coleville No. 1 gas strike of August 15th, 1951, and the closely following low gravity black-oil strike of August 23rd, were the first of a series of recent oil and gas discoveries in western Saskatchewan. They are in what is now known as the Coleville field, 25 miles north and west of Kindersley and 30 miles east of the Alberta-Saskatchewan border (Figure 1).Gas flows have been recorded in the Viking sand at daily rates of between 5 and 10 million cubic feet, and black oil of 15° A.P.I. gravity is produced from Mississippian sediments of Banff age at a daily rate .of 50 to 100 barrels on pump.Development drilling was carried on during the winter months, with very little attempt at step-out exploratory ventures. This year, however, a step-out programme to the northeast (Figure 2) is •being carried on in order to determine the position of a possible truncation of Mississippian sediments in that direction. Section 30 of the Coleville area has been fully developed on a 20-acre wellsite basis, and structural information is restricted to local rather than regional interpretation. No attempt will be made in this paper to interpret the Coleville area with respect to the regional geology in any but a general manner."

Jan 1, 1952

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By G. Vibert Douglas

NICKEL minerals are known in New Brunswick but have never been reported from Nova Scotia. The attention of the writers was drawn to an occurrence of pyrrhotite, reported to carry nickel, at the Second Gold brook, Middle river, Cape Breton. The purpose of this paper is to record the occurrence and give an account of the general geological association. In a later paper it may be possible to give greater details? than are available at present. GEOLOGY The area lies at the edge of a plateau of Precambrian rocks which forms the panhandle of Cape Breton island. This plateau has a general elevation of 1,200 feet. Middle river, with its tributaries, the First, Second, and Third Gold brooks drains the area. The lower country to east and southeast of the plateau is underlain by lower Carboniferous sediments. The rocks of the plateau are presumably of Precambrian age but have never been definitely correlated with the Gold-Bearing Series of the mainland. ?There i:s; however, some resemblance, although they have apparently been more intensely mountain-built. They are essentially fine grained, sheared quartzites and slates . The general strike is east and west, with a north dip of 45° to 55°. There are smalllocal drag-folds in the area. The only igneous rock in the immediate vicinity is an intrusive pink porphyry. It has small phenocrysts of quartz and feldspar. It has intruded the sediments generally along the structural planes, but in places crosses the structure . Its intrusive character is further proved by the fact that it contains xenoliths of the quartzite.

Jan 1, 1937

By A. M. Bell

"Hallnor mine is in the township of Whitney, Porcupine district. To date, its production of gold has been second largest in the east Porcupine field. Ore was discovered in the property in 1936 by diamond drilling in overburdened country. This drilling was undertaken by Noranda Mines following the discovery of ore in conglomerate at Pamour 1 mile to the east.Milling commenced at the Hallnor in June 1938, and to the end of 1945 432,000 oz. gold had been produced from 889,000 tons of ore, giving an average recovery of 0.49 oz. a ton.The West mine of Pamour, the Broulan orebody, and the veins on the Hallnor and Bonetal are all parts of a mile long vein system that has been separated into three sections by cross faulting. In consequence, they could well have been described in one paper. In treating them individually the viewpoint obtained from each may lead to conflicting opinions, and any conclusions advanced in this paper on the general structure should be modified by the conclusions advanced in papers on the neighbouring properties.GENERAL GEOLOGYRock FormationsThe Hallnor orebodies occur within 400 feet of the contact between lavas and sediments, and may lie in either lavas or sediments. The lavas near the ore consist of flows of pillowed andesite and one flow of more acid and less sheared and chloritized lava locally named trachyte. These flows strike east-west and dip steeply. At the surface on the east side of the property the volcanics have been intensely altered to a massive carbonate rock having a north-south thickness in excess of 1,000 feet . This carbonate body extends west across the property with a plunge of 45° (Fig. 1)."

Jan 1, 1954

By S. A. Jacob

Magnesium sheet is notoriously difficult to form at low temperatures without initiating failure, In the present work cold rolling and annealing conditions are varied to produce samples of AZ3lB sheet with a range of grain sizes. The formability of these samples is investigated using tensile testing and forming limit diagrams (FLD's), The results are discussed in terms of twin types and frequencies.

Jan 1, 2005

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

By M. Rafieazad, P. Fathi, X. Duan, M. Mohammadi, A. M. Nasiri

"Direct metal laser sintering (DMLS) is a metal additive manufacturing technology that creates highly complex components by fusing metal powder into a solid part. In this study, the impact of surface roughness on corrosion resistivity of AlSi10Mg_200C alloy manufactured through DMLS was investigated. The as-printed DMLS-AlSi10Mg _200C alloy was subjected to various surface finishing processes including grinding and sandblasting. The corrosion performance of the surfaces was then evaluated using potentiodynamic polarization testing and electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution to mimic seawater environment. Surface characterization and corrosion morphology of the samples were assessed by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy. The results of this study show that the surface finishing process and the resultant surface roughness has a significant impact on the corrosion resistivity of the DMLS-AlSi10Mg_200C alloy in the seawater environment.INTRODUCTION Direct Metal Laser Sintering (DMLS), also known as Selective Laser Melting (SLM) (Sames, List, Pannala, Dehoff, & Babu, 2016), Laser Beam Melting (LBM), or Laser Metal Fusion (LMF) (Herzog, Seyda, Wycisk, & Emmelmann, 2016), is an additive manufacturing process that utilizes a precise, high-power laser to micro-join powdered metals and alloys layer by layer to form almost fully dense and functional components in three dimensions from the 3D computer-aided design (CAD) data. Complex geometries not possible with conventional manufacturing processes can be readily manufactured with high accuracy using the DMLS process with no need to time-consuming tooling."

Jan 1, 2018

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

By R. J. Grant, D. W. Scott, M. A. Cooper, E. R. Shannon

"The Brunswick No.12 site concentrator processes 10,500 tonnes per day of a complex lead, zinc, copper and silver ore producing four concentrates by differential flotation. Research over the years has led to increased understanding about the mineralogical and flotation characteristics of the ore. A pilot plant study conducted at Lakefield Research, primarily designed to investigate the technical feasibility of semi-autogenous grinding, provided an opportunity to test recent theories about grind size,, reagent schedule and flowsheet configuration.A fundamental approach was taken with each of the unit processes involved in grinding and flotation. Basic operating and metallurgical criteria were established in each area and a step-by-step implementation program initiated in the plant.Significant improvements in metallurgical and financial performance have been realized through the application of basic grinding and flotation principles using conventional milling equipment and without major capital expenditure. Current operating practice is detailed and metallurgical advancements cited.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mines near Bathurst, New Brunswick. Brunswick is a publicly traded company with majority ownership held by Noranda Minerals (63%). In addition to the No. 12 underground mine, the company operates a lead smelter and phosphate fertilizer plant in Belledune, N.B. and maintains a 25% interest in a joint venture with Noranda Minerals' Heath Steele mine near Newcastle, N.B. Through the four operations, a total of 2000 people are directly employed with fixed assets totalling Cdn$187 million (BM&S, 1991)."

Jan 1, 1993

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990

By A. Alfantazi, L. Choudhary

Gold leaching in thiosulfate solution has attracted widespread research interest through the last two decades primarily due to its perceived environmental benefits in comparison to the conventional gold cyanidation technique. However, the data on the corrosion and/or corrosion-induced failures of plant infrastructure materials in the solutions relevant to thiosulfate gold leaching are very limited. Accordingly, this study aims to characterize the electrochemical corrosion behavior of stainless steel 316L in the thiosulfate gold leaching solutions. Electrochemical corrosion response was investigated using potentiodynamic polarization and electrochemical impedance spectroscopy. The morphology of corroded specimens was analyzed using scanning electron microscopy.

Jan 1, 2014

By Adrian White

Agenda Overview of pastefill at Kidd Mine Pipeline wear and the need to monitor Steel Loop monitoring Steel Borehole monitoring Monitoring pipe linings

May 1, 2013

By Mel Torrie

1 Want access to low level vehicle data so 3rd party apps can be applied as desired 2 Hardware Agnostic (COTS plug and play) 3 Common/Open protocols that facilitate integration and the coexistence of a variety of applications on a variety of equipment 4 Minimum computer hardware footprint 5 Technology Independence (including comm. backbone)

May 1, 2013