Search Documents

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By George J. Cymerman

Since 1978, Syncrude Canada Ltd. has been expanding steadily its oil sand mining and processing capacity while reducing unit energy requirements. At the current rate of ~180 M tonne/year oil sand, the originally adopted Karl Clark?s 80°C version of the Hot Water process would require some 53 PJ (53 x 1015 Joule) heat. If this amount of heat were to be derived from burning natural gas it would cost $369 M/y (at $7/GJ). Fortunately, effective recovery of waste heat from the upgrading operations at the Mildred Lake site obviated the need for water heating with natural gas. The oil sand hydrotransport technology, first utilized commercially in the mid-nineties at Syncrude?s North Mine, reduced slurry temperature from ~80°C to ~50°C, cutting the unit heat requirement from 293 MJ/tonne to 183 MJ/t. However, in the new 100 Mt/year Aurora Mine even a 50°C process temperature would still require 18 PJ of heat energy per year. Only limited quantity of 65°C water could be imported from Mildred Lake site and some waste heat would be available from Gas Turbine Generators. A new, Low Energy Extraction (LEE) process was developed to minimize heat requirements by further reducing process temperatures to 25°C in the slurry pipeline and 35°C in the Primary Separation Vessels (PSV). Unfortunately, when applied to certain ore facies in Aurora, the LEE process yielded disappointing bitumen recoveries, necessitating an increase in slurry temperatures from 25°C to 35°C in the pipeline and from 35°C to 42°C in Primary Separation. In 2004, an Optimized Low Energy process (OLE) was developed and piloted at Syncrude Research using a 2000 kg/hour pilot plant. In the OLE process, most available heat is applied up-front to produce 45°C pipeline slurry at a density of 1.58 kg/l. Once the pipeline conditioning process is completed, the slurry is flooded with cold (10°C) water, resulting in PSV temperature of 34°C. The overall heat and water requirements are the same, or slightly lower, compared to those of the LEE process ? but without the penalty in bitumen recovery. Processing 100 Mt oil sand at 34°C (96 MJ/t), rather than at 50°C (183 MJ/t), will save $61 M/y (@ $7/GJ) and reduce green house gas emissions by ~47 %. The OLE process is currently being implemented at the Syncrude Aurora Mine.

May 1, 2006

By P. Garritsen, J .. A. Blanco, M. C. Bell

"By 1994, Inco Limited will lower sulphur dioxide emissions from the Copper Cliffsmelter by 60% to 265 000 tonnes/year, primarily through implementing two key process changes. First, new milling technology will permit economic rejection of additonal pyrrhotite prior to smelting. Second, a bulk coppernickel concentrate will be oxygen flash-smelted, thereby eliminating the existing multi-hearth roasters and reverberatory furnaces . All copper will be recovered in the matte separation plant as a nickeliferous chalcocite, and will be oxygen flash-smelted for blister production. This paper outlines the development of the project and describes the process, including the flash furnaces, new sulphuric acid plant and additional oxygen plant.IntroductionInco 's SO2 Abatement Program will lower sulphur dioxide emissions at Sudbury from the current levels of 685 000 tonnes per year to 265 000 tonnes per year by 1994 as required by Ontario' s countdown on acid rain regulations.It is the high tonnage of sulphur mined that creates the magnitude of the SO2 emission problem at Sudbury. At a production rate of 240 million pounds of nickel per year, Inco mines 12 million tonnes of ore. At 10% sulphur it mines 1.2 million tonnes per year of sulphur. If Inco did not fix any of this sulphur it would be emitting 2.4 million tonnes per year of sulphur dioxide-about as much as all other Canadian emissions. Today, however, Inco is already fixing 70% of the SO2 in ore, in several ways : mostly as sulphur in pyrrhotite rejected to tailings in the milling operations; as acid from the roasting of pyrrhotite and some nickel concentrate at the Iron Ore Recovery Plant (lORP) and some as liquid S02 from the copper flash smelting furnace. By fixing 70% of the sulphur the current allowable SO2 emission levels of 685 000 tonnes per year is met. Total sulphuric acid production is currently 450 000 tonnes per year and in fact, the 10RP operation is being continued only to maintain established acid markets.Historically emissions have been reduced from the 2 000 000 tonne per year level to the current level of 685 000 tonnes per year by rejecting pyrrhotite from the smelter feed, and 70% of the SO2 containment problem at Sudbury has already been addressed.While Inco's profits are large at current nickel prices, most people have forgotten that back in 1982 Inco was losing a million dollars a day. Inco did make a dramatic response to this economic stimulus. The Ontario Division increased productivity by 65% and lowered costs to become the lowest cost nickel producer."

Jan 1, 1990

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

Spatial information Critical to a project since it underpins: ?Discovery of mineral resources ?Orebodydefinition and technical assessment ?Mine design and planning ?Profitability and project value Data ?Single most import asset. ?Good interpretation of quality data underpins project growth and success. TEAMWORK

May 1, 2002

By B. Oraee-Mirzamani

One the most important tasks after excavation of tunnels is the implementation and installation of a support system. Tunnel collapse poses a safety hazard and can cause worker injuries. In addition, it may have a severe economic impact because tunnel collapse can stop production and ore transportation. Therefore, an appropriate and well-designed support system is necessary for collapse prevention and to help stabilize the tunnels. In this research, we suggest a support system for the Parvade1 underground coal mine. The study case is a common mining roadway tunnel in the E1 longwall panel in this mine. To design an appropriate support system, we used the finite element method (Phase2 software). The results of this research can be used to design support systems for future tunnels in this mine and any coal mine that has similar conditions.

Aug 1, 2013

By D. W. Davis, P. Landais, L. J. Robb

Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Ph-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter Ol3C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoidand sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By Y. Masuda, Y. Nakamura, K. Haraguchi, A. Taniguchi, K. Arita

Availability of the elements originating from steelmaking slag for various marine phytoplankters including purely cultured strains and natural populations was tested in land and shipboard laboratories. The results obtained demonstrate that, although their solubility was not uniform among different slags, dissolved iron, silicate and phosphate from the slag stimulate phytoplankton growth. No negative effect of the slag addition on their growth was observed at lower dose, e.g. less than 200 mg/l. Since most coastal waters are the hypernitrogenous environment due to anthropogenic load of ammonium, the slag can be an ideal source of silicate and phosphate, which restore the hyper-nitrogenous condition into truly eutrophic condition with balanced Redfield ratio. In so-called HNLC (high-nitrate low-chlorophyll) oceanic areas such as the Southern Ocean and the subarctic North Pacific, where iron is almost only limiting factor of the phytoplankton growth, the slag could also be a source of iron and enhance CO2 fixation by phytoplankton photosynthesis. (Key words: carbon deposition in deep-sea, marine environmental remediation, phytoplankton, slag as a source of iron, phosphate and silicate.)

Jan 1, 2004

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

By D. J. MacKinnon

Zinc metal was first produced in India around 1100 A.O. and a zinc industry based on retorting gradually developed in both India and China(1) . The vertical retort method for smelting zinc ores was developed in England in the 1730s; this was followed by the more fuel efficient horizontal retort process developed by the Belgians in the 19th century(2) . The horizontal retort process was the standard method of zinc manufacture until the 1950s when it became obvious that it could not compete with electrolytic zinc technology(2). The present day extractive metallurgy of zinc is dominated by the electrolytic process which now accounts for almost 80% of the world's primary zinc production. In recent years the electrolytic zinc process has seen significant improvements: the fluid-bed roasting of zinc concentrates, improved leaching and residue treatment techniques such as the jarosite and goethite processes, improved solution purification procedures, mechanization of the zinc electrolysis step and of the zinc melting and casting operation. In addition, new leaching processes have been implemented for the treatment of oxidized ores, particularly silicates, and the pressure leaching of zinc sulphide concentrates is now a commercial reality. Although the electrolytic zinc process was first used on a commercial scale in 1916, its history can be traced back to the 1860s. The purpose of the present paper is to outline the early history of the electrolytic zinc process and to trace the significant developments which led to the first successful commercial electrolytic zinc plants.

Jan 1, 1999

By Robert Thomson

"The Cobalt camp is by far the most productive camp of the Temiskaming silver-cobalt area. The date of discovery, 1903, is an important one in the history of Canadian mining; from then on prospecting and mining grew rapidly to take the prominent places they now hold in Canadian life.At Cobalt, prospectors and operators, who were to play prominent parts in other Canadian camps, received their initial training. The exploration campaigns leading to the discovery of several new camps were organized at Cobalt, and a considerable part, indeed, of the funds for these campaigns were profits from mining at Cobalt.The discovery of the Cobalt camp was purely accidental, not the result of any purposeful search. Fred LaRose, a blacksmith employed in the construction of the Temiskaming and Northern Ontario Railway, discovered mineral, afterwards determined to be valuable, within a few feet of the right-of-way. This discovery became part of the very productive LaRose mine. The publicity given this discovery, particularly by Willet G. Miller, later Provincial Geologist of Ontario, led to the rapid development of the camp.ProductionCobalt is a great camp by virtue of its silver production; cobalt is also important, although clearly subordinate. Copper, nickel, arsenic, and bismuth are by-products of mining for silver and cobalt and have not been of great importance to date.The following table gives the metal content of ores, concentrates, etc. from the Cobalt camp for the years 1904 to 1954 inclusive, as reported by the mines (l):"

Jan 1, 1949

By Robert A. Creaser, Iain Mitchell, Robert L. Linnen

Abstract - The Bermuda Zn-Pb showing is hosted by dolomitized Blue Fiord Formation of Devonian age, located east of the Ensorcellement dome on the Grinnell Peninsula of Devon Island. Fluid inclusions in hydrothermal calcite indicate that the mineralization precipitated from low-temperature, highly saline brines. The ?34S compositions of sphalerite, galena, and marcasite range from 16.1‰ to 35.2‰. Consequently, the Bermuda showing is interpreted to be Mississippi Valley-type (MVT) mineralization. The apparent age of mineralization has been determined by the Rb-Sr method from sphalerite separates, and a Late Devonian age of 357 ± 50 Ma (MSWD=65), with an initial 87Sr/86Sr ratio of 0.7083 ± 0.0020 is indicated. This date, within error, is the same as the Polaris deposit. This suggests that the mineralization formed during the Ellesmerian Orogen, although it is also possible that mineralization is associated with extension, related to the opening of the Sverdrup basin. The strontium and sulfur isotopes and fluid inclusion analyses indicate the involvement of a brine that acquired its salinity from interaction with evaporites, lower in the stratigraphic succession. The Polaris mine is the type deposit in the Cornwallis Zn-Pb district and is hosted by the Thumb Mountain Formation. The results of this study are significant because they demonstrate that regional brine movement is more widespread than previously recognized, and that MVT mineralization in the Cornwallis Zn-Pb district is not restricted to the Thumb Mountain Formation.

Jan 1, 2004

By J. H. Rickard, D. H. Watkinson

"Abstract - Detailed petrographic and quantitative (electron microprobe, SEM-EDS) mineralchemical analyses of sulfide ore from the 100 orebody at the Copper Cliff North mine, Copper Cliff, Ontario, reveal numerous stages of ore development. Sharp contacts between weakly mineralized quartz diorite and blebby to massive sulfides indicate multiple intrusive events within the Copper Cliff offset dike. A spatial association of sulfides and hydrous minerals, such as amphibole, biotite, chlorite and epidote, suggests that most primary ore has been affected by later hydrothermal fluids. Sulfides are often enclosed or bordered by these secondary silicate phases. The ore consists primarily of pyrrhotite, pentlandite, chalcopyrite, with trace michenerite, cobaltite/gersdorffite, irarsite, hessite, tsumoite, and bismuth tellurides.Geological and petrological comparison of the 100 orebody and the adjacent 900 and 890 orebodies has revealed distinct similarities in ore distribution. Data show that the 100 orebody is depleted in platinum-group elements (PGE) relative to the 900 orebody. Platinum-group elements from the 100 orebody may have been hydrothermally remobilized and partly emplaced in the 900 orebody, in adjacent veins, or in magmatic breccia. Analysis of Cu, Ni, and PGE assay data of ore samples has characterized their distribution among the eight different ore textures in the orebody. There is a strong association between Pt and interstitial sulfide, and to a lesser extent massive sulfide, but little correlation between chalcopyrite-rich ore and PGE in the 100 orebody, unlike many other deposits in the Sudbury region."

Jan 1, 2001

By K. Nagy

To support the implementation of its integrated SHEQ Policy, Cameco has undertaken an environmental leadership initiative with the goal of moving beyond regulatory compliance and significantly reducing environmental impacts in five key areas: air emissions, treated water quality and quantity, energy use and greenhouse gas emissions, and waste generation. To ensure environmental leadership becomes routine business practice, it was necessary to integrate the initiative into Cameco?s programs and management systems at the corporate and operational levels. Operations based environmental leadership strategies and action plans have since been developed, as well as a corporate reporting system to monitor Cameco?s environmental performance.

Aug 1, 2010

By Theophile Yameogo

The rock mechanics literature has documented the challenges, failures and successes of tunneling through weak rocks. Cases usually deal with low RMR rock masses or high stresses in a fractured zone. With the combination of 5MPa water pressure, 14 RMR ground with clay infillings and ground freeze walls, the case of the 510-8225N development drift at McArthur River is certainly much more challenging, especially when high grade uranium production is at stake. The article explains the excavation and the ground control techniques that were used to overcome the challenges of development at the Unconformity in the Athabasca Basin.

Aug 1, 2010

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By R. A. Gannicott

Trend surface analysis was used to investigate the geochemical dispersion patterns of Si, Ai, Fe, Mg, Ca, Na, K, Ti and Rb in the footwall of the Seneca massive sulphide prospect in southwestern British Columbia. Surfaces for various element ratios were also produced to see if the distributions of the elements are related to each other. Trends developed by the elements redistributed during hydrothermal alteration may be difficult to detect for various reasons, such as too few and widely separated sample points, random analytical errors or local variations in rock chemical composition that are not related to regional trends. Trend surface analysis is useful to distinguish regional trends from local fluctuations. The computer program used in this study is capable of calculating surfaces up to the 6th degree polynomial, but provides for automatic termination when the variables in the equation for successive surfaces become effectively collinear. With the relatively small number of data points used (21 samples) in this study, such termination occurred after the quadratic surface. Results show that, at the Seneca prospect, Mg and K increase, and Na and Ca decrease, toward a common centre which corresponds closely with the best drill-core intersections of ore. The centre is interpreted as a volcanic vent and as the source of mineralization . Quadratic surfaces for element ratios show that K/Ca decreases and Fe/Mg increases away from this vent. Thin-section and X-ray diffraction analyses indicate that these variations reflect sericitization of plagioclase and an increase in the Mg content of chlorite near the vent. The mineralization , rock types and element dispersion patterns at the Seneca prospect are similar to those reported for volcanogenic massive sulphide deposits at Bathurst, New Brunswick, and in the Hokuroko district of Japan.

Jan 1, 1979

By D. B. Dreisinger, A. A. Gunaratnam

A pressure oxidation (POX)-hot cure (HC)-lime boil (LB) process is used in industry to recover silver from refractory gold sulfide ores containing minerals such as pyrite and arsenopyrite. Pressure oxidation is used to oxidize minerals and liberate occluded gold particles. As such, iron goes into solution and under acidic and high temperature conditions often precipitates as basic iron sulfate (BFS). BFS consumes excess lime during neutralization prior to cyanidation. Therefore, a hot cure stage is required to re-dissolve BFS back into solution. BFS re-dissolution consumes acid and produces ferric sulfate. In the presence of silver, these conditions favor the slow formation of silver jarosite. Silver jarosite is refractory to cyanidation, and must be broken down prior to cyanidation. This is done in the lime boil to produce a cyanide-soluble silver hydroxide. A study was conducted to investigate parameters that affect the precipitates that form in each stage of the POX-HC-LB process.

Jan 1, 2017