Search Documents

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By A. H. Duffield

"Forming part of the Prairie Evaporites, the sylvinite layer mined at Alwinsal underlies the Blairmore quicksands and the water-bearing Devonian formations. Production is achieved by a method of trackless, continuous mining of rooms, leaving pillars for natural support. The paper describes the development of the mine, and the equipment and organization employed in the operation and maintenance of the underground facilities."

Jan 1, 1972

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990

By A. M. Elmahdy, T. Hirajima, M. Farahat

"Separation of molybdenite from chalcopyrite is mainly achieved through flotation technique to raise their grades up to 25% to be extracted in smelters. However, molybdenite recovery and grade obtained from this process is not satisfactory in most cases due to the natural hydrophobicity of both minerals. The influence of conventional heat treatment on pure chalcopyrite and molybdenite minerals was investigated. X-ray diffraction, TG-DTA and XPS techniques were applied before and after heat treatment. The results showed phase changes for both minerals. Magnetic separation experiments of single and mixture of both minerals at several magnetic intensities were made. For single mineral experiments, 100% molybdenite recovery was obtained at all experimental conditions as non-magnetic fraction whereas ca. 100% chalcopyrite recovery was achieved under certain conditions. In case of 1:1 binary mixture, 87% and 83% molybdenum and copper recoveries, respectively, were obtained. The increase in chalcopyrite magnetic recovery is related to the formation of more magnetic phases as confirmed by characterization techniques.The objective of this study is to increase the magnetism of chalcopyrite to make its separation from molybdenite by magnetic separation possible and to understand the mechanism behind it. These results indicate that it may be possible to upgrade molybdenite ores using heat treatment followed by magnetic separation to the required grade by smelters which is difficult to attain by froth flotation and the other techniques."

Jan 1, 2016

By S. N. Kalyakin, D. S. Flett, M. A. Mulagaleeva, N. V. Gudkova, S. S. Serdyuk, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina, V. G. Lomayev

"The Chuktukon niobium-rare earth elements ore deposit is located in Siberia (Russia). Weathered carbonatite crusts are the basis of the ore deposit. The deposit itself is 3.5 km in length, about 800 to 1400 m in width and up to 200–300 m in thickness. The ores are composed of iron-manganese oxides (hydrogoethite, hematite, psilomelane, pyrolusite) and contain 3–7% of rare-earth phosphates (florencite, monazite) and 0.5–1% of niobium oxide (pyrochlore). The ore is completely finely dispersed and consists of oxide particles formed of compact, dense aggregates which makes ore dressing as well as leaching of the rare and radioactive elements very difficult. Several options for processing of these ores have been considered: 1) reduction of the iron oxides to magnetite followed by beneficiation with magnetic separation to produce a rare metal concentrate; 2) processing of the rare earth elements (REE) containing minerals by direct alkaline-acid treatment; 3) processing of the ores using nitric acid leaching in an autoclave.INTRODUCTIONThe Chuktukon niobium-rare earth metal ore deposit is located in Siberia, in the Krasnoyarsk region, 110 km from the Boguchan hydroelectric power station which has recently been commissioned. This mineral raw materials is capable of providing impetus for the modernization of the Russian rare metal industry because of its qualitative and quantitative characteristics. The deposit is located in a region of promising industrial development and is a part of the territoriy where the Russian Federation’s Program “Complex Development of the Lower Angara Region” is currenly being realized. The main program directions are creation and development of industrial activities in sectors such as power, metallurgy, oil and gas, gold, rare-metals, and timber. The program will aid the development of the niobium and rare-metal resources of the Lower Angara and neighbouring regions as well as increase the national production of REE and therefore import substitution (Lapin, 1997; Lomaev & Kuzmin, 2003; Lomaev & Serdyuk, 2011; Serdyuk, Lomaev, & Kontorovich, 2000)."

Jan 1, 2016

By Y. Jiang, B. Li, R. Liu

"In this study, laboratory flow tests were conducted on 2-D artificial rock fracture network models containing a single intersection constituted by two inlet and two outlet branches. Three models with different intersecting angles of 60°, 90° and 120° were tested using both dye solution and distilled water. Constant flow rates were imposed on one inlet, and the flow patterns in the fracture intersections were captured by using a CCD camera. The test results were compared with the predictions made by numerical simulations that solved the Navier-Stokes equations. The results revealed that when Reynolds number (Re) is as low as less than 1, the intersecting angle has negligible influence on the flow rate of each branch and the flow patterns within a fracture intersection. As the interesting angle ? and Re (e.g., from 10 to 200) change, the normalized flow rates of different outlet branches change significantly, due to the inertial effect of fluid flow. These changes could be represented by a series of mathematical expressions involving Re and ?, which could be applied to fracture network models to improve their prediction accuracy on hydraulic properties (e.g., permeability and breakthrough curves of particles) of rock masses. INTRODUCTIONCoupled stress, flow, heat and mass transport are the corner stone subjects for many geoscience and geo-engineering disciplines, such as geological disposal of radioactive waste and geothermal energy exploitation. Many outstanding issues need to be investigated to enhance the knowledge on these subjects, and specifically more in-depth research in testing and modeling of the fluid flow in fractured rock masses is needed. In recent years, discrete fracture network (DFN) models have been extensively used to study the fluid flow and mass transport behaviors of fractured rock masses (e.g., Min et al., 2004; Zhao et al., 2011). In these models, each fracture is usually represented by a parallel-plate model, in which fluid flow exactly follows the cubic law. Therefore, comparative flow rate in each outlet branch of an intersection in these models only depends on its aperture. In reality, due to the surface roughness of fractures, the magnitude of mechanical aperture is usually larger than that of the hydraulic aperture of each fracture (Li et al., 2008; Xiong et al., 2011), and abundant flow patterns could exist in an intersection, influenced by its geometry, varying with changing Reynolds number (Re) (Kosakoswski & Berkowitz, 1999). Recent studies have also revealed that different mixing patterns might exist at a fracture intersection, bounded between streamline routing model and complete mixing model, that determine the final distribution of solutes in fractured rock masses (Johnson and Brown, 2001; Park et al., 2001). Numerical simulation has been the principal method adopted in previous studies, and the studies conducting flow tests on intersected fractures are less reported (Wilson & Witherspoon, 1976; Johnson and Brown, 2001). In this study, laboratory flow tests and numerical simulations by solving the Navier-Stokes equations were conducted on 2-D models containing a single intersection constituted by two inlet and two outlet branches, intersected at different angles. The main objective is to study the influence of intersecting angle on the flow behavior of the intersected fractures and the variations of flow patterns and fluid redistribution in each model along with the changes of the Re and the intersecting angle ?. The influence of surface roughness was not considered."

Jan 1, 2015

By J. L. Gartshore

PRACTICALLY all of Quebec's chrysotile asbestos production derives from twelve mining and milling operations located in the "Eastern Townships" area of the province. The annual output of these twelve operations exceeds one million tons of chrysotile asbestos, valued at over one hundred million dollars, and is shipped to manufacturers spread over all six continental areas of the world. A total of approximately twenty million ton of asbestos ore yearly, or about seventy-five thousand tons a day, is mined. Individually, the operations vary in size from about two thousand tons to thirty thousand tons per day. Removal of waste rock and overburden to develop these ore tonnages varies greatly from one mine to another, but would probably average out at about a one to one ratio.

Jan 1, 1962

By G. Beckstead, L. Gormely, R. Zimmer, K. Hanneman, B. Nethery

As part of the EIS and permitting activities for the Pogo Mine in Alaska, a risk assessment study for the water management plan was carried out. The basis for the study was a site water volume and contaminant balance model. Probabilistic modeling was carried out using the @Risk Monte Carlo simulation package to investigate the frequency, quantity, and quality of discharges under varying assumptions. The results were used in discussions with regulatory officials as part of the permitting process for the project. The simulation allows probabilistic modeling of key environmental parameters based on input frequency distributions involving both quality and quantity of flow. When combined with predictions of water treatment plant capacities and removal efficiency, this was very useful for defining the likelihood of important regulatory outcomes. Based on the model, certain project modifications were made. Using the simulation as a basis, ongoing dialog with regulators led to consensus that all potential risks have been considered and mitigated for the Pogo Mine according to their likelihood and severity, and that regulatory requirements would be achieved. The paper describes the model and some of the applications for which it was used.

Jan 1, 2005

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By J. Dupre, A. Gontcharov, H. Pepin

Produced by the conventional TIG welding CMSX-4 welds had been studied. It was demostrated that microstructure of welds depended on filler materials, welding parameters and joint design. Epitaxial solidification of CMSX-4 clad deposits produced a directionally solidified structure while welding with the similar filler material. Defects free clad welds were obtained by TIG welding without preheating using similar and dissimilar filler materials.

Jan 1, 2006

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By E. Y. Dougherty

Introduction As practised during the last two years at the Vipond Consolidated gold mine, mining geology has meant the application of geology to the problem of finding, developing, and mining ore. This article reviews the results attained in Vipond mining geology as thus defined. Most effort was directed toward clarifying and interpreting the tangible physical causes of vein and ore localizations, and in the following pages these questions are dealt with in considerable detail. Discernment of the influence of rock folding and deformation on the localization of veins, and of the influence of certain structures and rocks in or near carbonaceous zones on the localization of ore-bodies, have been the main practical results of the studies. Consideration of some of the geological features of the Porcupine area, and of the geology and mining experience of the principal producing mines, has helped toward a perspective of Vipond's ore-finding problems. These features are first discussed. The background and procedure for Vipond mining geology, and the major results of the geological mapping, are then summarized. Then follows a résumé of tangible factors that influenced vein, ore-body, and gold localizations; and, next, explanations of the facts ascertained. Because they were found of little utility, many fascinating problems, such as the origin and mode of emplacement of the veins and lodes(l), the ultimate source of the ore, and the physico-chemical and mechanical agencies affecting vein and ore formation, are treated cursorily or are neglected in these notes.

Jan 1, 1934

By N. R. Andrade-Gonzalez

The present work was performed on four alloys containing Al-6 2 wt pct Si-3 5 wt pet Cu, with magnesium in the range of 0.02-0 40 wt pct, and strontium in the range of 0-165 p p m Tensile bars were cast in a permanent mold (ASTM B108-160) and heat treated at 495°C for 4 hours, followed by quenching in hot water. Two different artificial aging temperatures were applied at 180 °C and 220 °C for times from 0 5 h up to 8 h Tests were conducted with the intent of determining how the mechanical properties of an aluminum-based 319 alloy are affected when aging time and temperatures are varied In general, it is seen that the alloy does not exhibit the common peak-overaged aging condition due to the presence of several coexisting phases, indicating that they form through complex eutectic reactions late in solidification.

Jan 1, 2004