Search Documents

By Robert A. MacGregor

"Following several months of test work, water leaching in mined-out areas at Stanrock commenced on a production basis in February, 1963. A combination of fast high-pres-sure washing and rewashing of stopes on a predetermined cycle, and the intermittent sprinkling of low-grade heaps, using both fresh water and recirculated acid water, has proved most successful. There was also a correlation of daily sampling data points to a relationship between the leach water grade and the grade of the material being washed, the leaching time and the location along the dip. An increasing tolerance for uranium by the acid-producing bacteria is also indicated. A steady production rate of 10,000 to 12,000 lbs. of u.08 per month is being maintained, with an over-all mine water grade of 0.25 lb. per ton and a pH of 2.3."

Jan 1, 1966

By R. C. Gilmore, J. F. Brune

"Pulverized limestone rock dust used in United States underground coal mines to prevent and suppress coal dust explosions must easily disperse by forces of a methane or coal dust explosion. Moisture in the mine environment causes caking of the dust. Colorado School of Mines researchers performed dispersibility tests in a full-size explosion test drift. Tests included conventional, hydrophobized, and rock dust approved for German mines. Conventional and German standard rock dust products partially agglomerate, which may not be effective in suppressing a coal dust explosion, while hydrophobic rock dust retains better dispersibility.INTRODUCTIONA coal dust explosion devastated the Upper Big Branch mine in 2010 resulting in the death of 29 miners, the worst mining accident in the United States since 1972. The explosion propagated through approximately 65 km of active mine workings, but was extinguished in areas that had been properly rock dusted (Page, 2011). Researchers have long studied and established the ability of inert limestone rock dust to suppress coal dust explosions, see Richmond et al. (1975), Cybulski (1975), and Sapko et al. (2000).To be effective, rock dust must contribute to a total inert content of > 80% by weight and 100% of rock dust particles must pass through an 850 µm sieve, while 70% of the rock dust must be finer than 74 µm. This is established in US regulations 30 CFR §75.2. Dry rock dust is a nuisance that prevents mining work downwind from rock dusting activities. To overcome this problem, dust manufacturers have proposed applying the rock dust as a wet slurry or foam. After drying, manufacturers expected the slurry or foam-applied dust to have the same explosion suppression capabilities as dry-applied rock dust.Researchers at the Colorado School of Mines (CSM) designed and built a full-scale, underground Explosion Test Facility (ETF) at the CSM Edgar Experimental Mine in Idaho Springs, Colorado about 20 miles west of the CSM Golden, Colorado campus. To disperse the different rock dust products, researchers produced an air pressure pulse using a mesh array of PETN detonation cord. This method is simpler, more reproducible and safer than other methods considered, including methane-air explosions and a compressed air cannon. The detonation cord blasts produce a wind velocity of 30 to 50 m/s, the minimum velocity at which coal dust explosions can propagate, based on research by Nagy (1981) and Cybulski (1975)."

Jan 1, 2019

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By E. S. Moore

In the townships of Genoa and Marion, Subdury Mining Division, Ontario, there is a group of twenty-three mining claims known as the Jefferson claims. They are controlled by the Jefferson Mining Corporation and they were staked in 1908 by W. E. Smith, formerly of Sudbury, Ontario, and now of Smith & Reitz, a law firm of Minneapolis, Minnesota. These claims were staked for iron ore and in 1910 about 4000 feet of diamond-drilling was done on them. During the drilling operations galena and sphalerite ~were found in the iron formation in cores from holes, Nos. 2 and 3, claim W. D. 717, Genoa township. This discovery lead to a search for galena and sphalerite in the vicinity and a streak of rock containing these minerals was found in the iron formation a short distance to the east of. the drill holes. A shaft was sunk on this outcrop in 1912 to a depth of 8 feet and bottomed in an attractive lens of galena. Stripping revealed other small exposures of galena and sphalerite in the iron formation.

Jan 1, 1926

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

By M. Hall

"SomarioEl circuito de molienda a Selbaie consta de molino semiaut6geno en un circuito cerrado y molino de balas en un circuito cerrado. El amperaje del motor de se usa controlar el tonelaje el molino. Este sistema estabiliza el circuito pero no mejora activamente el rendirniento del circuito. Se desarroll6 auxiliar el rendimiento del circuito un sistema experto en manipular las objetivos de existir control proporcional-integral. Se ejecut6 el sistema con el Comdale /C conjunto del sistema experto y ha side funcional hace tiempo el mayo de 1992. El sistema experto ha resultado en un aumento en tonelaje de 7tph y una disminuci6n de $210,000 en el caste anual de media de molienda. Se describe el desarrollo del sistema y los provechos derivar se presenta.AbstractThe grinding circuit at Selbaie consists of SAG mill and ball mill closed circuit grinding. The SAG mill motor current is used to control throughput. This system stabilizes the circuit but does not actively optimize circuit performance. An expert system was developed to aid the optimization of the circuit by manipulating the set-points of existing PI control loops. The system was implemented with the Comdale /C expert system package and has been on line since May 1992. The expert system has resulted in a net increase in tonnage of 7tph and a decrease in annual grinding media costs of $210,000. The system development is described and the benefits derived are presented."

Jan 1, 1994

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By K. S. Fraser, H. J. H. Pieterse

"A pressure oxidation plant to pretreat refractory sulphide ore at the Goldstrike plant in Nevada, was commissioned in early February 1990. The plant, with a nominal capacity of 1363 t/d, was commissioned over a one-week period and achieved design capacity and availability within ten weeks an unusually short period for a plant of this complexity.The pressure oxidation process is conducted under elevated temperature and pressure conditions, and in a corrosive environment. These conditions demand that the process and engineering design of the plant be carried out in a much more sophisticated and detailed manner than is normally required in a conventional gold plant.This paper provides an account of the process and engineering design of the Goldstrike pressure oxidation plant with special emphasis on the design of the vessels, slurry pumps, piping, valves, and control systems.BackgroundLocationThe Goldstrike property is located in Eureka County in northcentral Nevada on the Carlin geological trend. The mine is approximately 40 km northwest of the town of Carlin which is situated on Interstate Highway 80. The minesite is located 1700 m above sea level in the Tuscarora Mountains.Initial Goldstrike OperationsShallow, low-grade mineralization was discovered by diamond drilling in the Goldstrike area in the 1960s. A heap leach operation was established in the mid-I970s by the previous owners. The Post deposit was discovered in 1982. Gold production by mining and heap leaching reached I t/a (40 000 oz/a). American Barrick purchased the property in 1987 and started an aggressive program of deep drilling. This led to the discovery of the Betze and Deep Post deposits and established sufficient reserves to justify an initial 4100 t/d mill and a 5 500 000 t/a heap leach operation"

Jan 1, 1992

By D. M. Morrison

"Microseismic systems at five mines in the Sudbury Basin provide the basic data for Falconbridge Limited's rockburst research. Daily and long-term analysis of this data as well as underground observations has confirmed the fault-slip mechanism of rock bursting at three mines. A detailed analysis of the complete history of Falconbridge Mine is being conducted and Distinct Element numerical models are being used to simulate both the stick-slip behaviour of faults and the dynamic effects of the induced vibrations on rock and backfill. University research includes acoustic tomographic imaging of the rock mass based on seismic wave propagation and collection of full micro seismic waveforms to allow application of advanced seismic and statistical analysis techniques. INTRODUCTIONFalconbridge Limited currently has five mines operating in the Sudbury Basin: East, Lockerby, Onaping, Fraser, and Strathcona Mines, which along with the Falconbridge open pit produced 2.8 million tonnes of ore in 1986. The underground mines range from about 600 m to 2000 m below surface and one of the consequences of mining at these depths is the occurrence of rockbursts.Research into rockburst phenomena at Falconbridge began over 25 years ago and research is continuing in an effort to avoid the problem by improved mine design, to protect mine openings from damage by design of effective support systems and to better understand the processes which precede a major fault slip rockburst. Since the early 1980s, significant progress has been made due principally to micro seismic monitoring and advances in microcomputer technology coupled with detailed underground investigations.It is now possible to identify the fault-slip mechanism as the cause of many of the rockbursts which occur at Falconbridge mines. By gaining an understanding of effect of mining-induced stresses on the pre-existing geological structures, areas which may experience rock bursting can be identified and can be protected against severe damage by appropriate support techniques."

Jan 1, 1989

By W. D. Bonisteel

In 1976, Rio Algom Limited began the expansion of uranium production facilities at Elliot Lake. Quirke Mine was the only property in operation at the time, and plans were made to expand its milling capacity from 4,500 to 7,000 tons of ore per day. Following this expansion, other properties in the area will be reactivated to fulfill long-term contracts for uranium. As part of the expansion program, it was decided that in view of the escalating cost and impending shortage of energy, heat reclaim and conservation would be employed wherever practicable. In general terms, heat reclaim applications fall into three main classifications: ventilation, utility and process. Two of the ventilation applications and one process application will be described in some detail. Several other systems will be presented briefly as a matter of general interest. Some future possibilities will also be mentioned, together with their potential for economical heat recovery.

Jan 1, 1979

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

By D. A. Sloan

THE Young Davidson mine is of particular interest because of the extremely low costs and also because of the novel method devised for pillar recovery. The outstanding feature of the mining system is its simplicity and regularity. The successful operation of this property was de-finitely assured by the rise in price of gold in 1934. The mine is situated in the southeastern part of Powell township, about forty-five miles southeast of Timmins, Ontario. The local town, two miles distant, in Matachewan, which is twenty-five miles northwest of Elk Lake, the terminus of a branch line of the Temiskaming and Northern Ontario railway. Mining is confined to one of a group of five claims. The ore occurs in a body of syen.ite porphyry which is intruded along a contact of Timiskaming conglomerates with Keewatin altered ruffs and greenstones. This intrusion extends in a north-easterly direction from Davidson creek for 3,300 feet, of which length 700 feet lies within the Matachewan Consolidated property. The maximum width of the mass is 700 feet; it tapers off as it extends east-ward. The Orebody.-The syenite porphyry is of three types, probably all differentiates of the same magma, but only one of them is gold bearing. This is a cherry-red, coarsely crystalline type which forms the central part of the mass. It is more brittle and more fractured than the others, and consequently has allowed easier access to the gold-bearing solutions. The gold has been brought in by a branching system of quartz veins and along minute fractures. It is mainly in the form of very fine 'free' gold, but also occurs in pyrite, which is the chief metallic mineral.

Jan 1, 1942

By R. J. Mitchell

"High narrow backfills of significant strike length approach the stress conditions associated with a free standing wall but this lower bound design approach is not considered efficient for earth structures. This paper considers the design of high narrow backfills using upper bound limit analysis, retaining wall theory with backfill arching and centrifuge model tests. Complex toe support situations pertaining to operational factors at Falconbridge's Lockerby Mine are investigated. It is shown that the susceptibility of high narrow fills to toppling is much lower than anticipated from the retaining wall analysis and that toppling can be avoided by a suitable toe support. It is also concluded that adhesion between the fill and an adjacent pillar can markedly increase the stability of the fill. INTRODUCTIONFalconbridge's Lockerby Mine pillar projects will expose cemented tailings backfills to heights (H) up to 55 m. The exposed backfills may have strike lengths (L) greater than the heights but are relatively narrow, having widths (w) of up to 12 m. The bulk cement content of the fills varies from 8.3% (12.1 T:C) to 3.0% (33.1 T:C). Exposed faces may have up to a metre of overhang due to stope overblasting, as shown in Figure 1. These fills have a solids specific gravity of close to 3.0 and were placed at a pulp density of about 68%. The tailings have a fairly uniform grain size with 32% less than 0.075 mm (200 sieve) and about 12% slimes (less than 0.02 mm sizes). The fill exposed by early pillar removal will be backed by adjacent, near vertical, ore pillars. Future pillar removal may expose similar fills which are not supported by an adjacent ore pillar but which will be backed by either an open void or by uncemented backfill. Furthermore, these fills may be undercut when the pillar slot is driven, further reducing stability (case 3, Fig. I) or a wedge could be left to help support the fill (case 2, Fig . 1). This paper presents limit equilibrium analyses for these various backfill conditions in a 22: 1 T:C fill and com- pares the results to data from centrifuge model studies at a scale factor of A= 157 as indicated in Figure I. Prototype fills have a 6 m deep cone plug of 16:1 T:C which is accounted for in the comparison of centrifuge model test with analytical results."

Jan 1, 1989

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By T. P. Johnson, A. Vathavooran

"Conventional mining operations can produce a wide range of wastes containing gold and other precious metals but which are less suitable for processing by traditional methods. There are also types of ore that do not fit easily into a traditional processing flowsheet, e.g. because the refractory nature of their minerology or the combination of valuable metals is less suitable for traditional processes. Nevertheless, these potential sources of valuable metals remain unexploited resources that have attracted growing interest in the metals and mining industries over recent years. The challenge is therefore to develop and use alternative processing methods that have the flexibility of operation to cope with a wide variety of material types and tonnages, whilst providing high recoveries for valuable metals. Tetronics’ DC plasma smelting technology achieves industry-leading recovery rates for precious metals from a wide range of input materials and initial precious metal concentrations, whilst generating an inert slag-based material as a by-product (even when starting from a hazardous waste input material), approved within the EU for use in construction applications. This paper describes how this technology can be used as a key part of an overall process for the recovery of precious metals from these interesting materials.INTRODUCTION The extraction of gold from its ores by various forms of cyanide leaching has been practised by the mining industry for over a century (Minerals Council of Australia, 2005) and it remains the primary extraction method in a wide range of mining operations. The ability of cyanide to extract gold efficiently and quickly from lower grade ores without extensive additional processing, coupled with well-known methods to recycle the cyanide for re-use within the process mean it is often both the most economically preferable and environmentally acceptable method for recovering gold. As a result, 88% of all gold produced from mines in the USA in 2014 was recovered via leaching of open heaps or dumps (UGGS, 2016). Nevertheless, there are occasions where certain combinations of mineralogy and other circumstances reduce the effectiveness of cyanidation techniques, so that ever more elaborate additional processing steps are required, with inevitable increases in operating costs (Swash, 1988). In these circumstances, which are likely to be more common in future as ore qualities diminish, other methods of extraction may offer better alternatives. Whilst much less commonly used for Au extraction at present, pyrometallurgical methods are amongst the longest-established of these alternative approaches and merit serious consideration in such cases."

Jan 1, 2017

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By F. A. Forward

"NINETEEN sixty-six is a year of unusual significance in our Institute and in our country. It marks two-thirds of a century of service by the Institute to the people of the mineral industry and two-thirds of the century that Sir Wilfred Laurier said ""belongs to Canada."" As we meet here today within the historic walls of Canada's oldest city, a city that looks back on three hundred and fifty years of progress, I am reminded that it is almost a third of a century ago -in April, 1934 -that here in Quebec I first attended an Annual General Meeting of the Institute. It occurred to me that it might be appropriate to examine briefly the change that the middle third of this century has brought in the affairs of the mineral industry and, with some trepidation, to consider the prospect for the third that lies ahead.Opinions differ as to the relative importance of factors that have been responsible for the expansion and growth of Canada in its first hundred years. Some will say that it has been due to the abundance and fertility of agricultural land, others to the early enterprise of the railroads, and financiers believe that the banking system has been a major factor; -the fisherman -the forester -the teacher -each has his own view. I suspect, however, that most of us here would subscribe to the thesis of T. A. Rickard -miner, author, imperialist -who wrote, a gene-ration ago, ""Trade follows the flag, but the flag follows the pick,"" and thus agree that the finest contribution to progress, to wealth, to extension of frontiers and to inter-national trade has been provided by the mineral industry."

Jan 1, 1966

By W. C. Whittaker

Introduction When one thinks of a coal stripping deposit, the picture that usually comes to mind is that of a more or less flat seam from two to twenty feet in thickness overlain by ten to fifty feet of overburden, in suitable ratio for economic operation. This is the usual type of stripping deposit and is quite a common occurrence in various parts of the prairie provinces. Rather unusual types of coal stripping deposits are being presently worked as open-cut mines by Sterling Collieries, Limited, and the Co al Valley Mining Company, Limited, at Miles 47 and 48 on the Alberta Coal Branch, some 150 miles south west of Edmonton. These deposits are of interest chiefly because they represent turned-up and greatly thickened sections of the Mynheer seam, and as such they present their own problems, peculiar to the commercial exploitation of a seam of this type. The area in which these deposits occur was originally owned by the Pacific Pass Collieries, whose operations, however, were confined to under-ground mining at Lovett, some eight miles to the southeast. It was not until l918 that the value of these deposits was realized, when the Company now known as Sterling Collieries, Limited, opened their pit at Mile 47. At the inception of the work, coal was loaded directly into the railway cars by men using wheelbarrows. In 1920, a tipple was built, after which the coal was loaded by steam shovel into mine cars, hauled by steam dinkeys, and loaded over the tipple into railway cars. In 1922, the Coal Valley Mining Company entered the field at Mile 48, with an entirely mechanical equipment, and at the present rime these two are the only stripping properties in Alberta using mechanical equipment both for the removal of overburden and the loading of the coal. These Companies have operated continuously since that time, and have to date mined and shipped 4,000,000 tons of coal, and moved some 5,255,000 cubic yards of stripping. The present annual coal output for the two mines is about 240,000 tons.

Jan 1, 1935