Search Documents

By Nicholas J. Welham

"The effect of extended ball milling has been studied for two industrial processes: (1) the processing of metal sulphide concentrates; and (2) the carbothermic reduction of ilmenite to synthetic rutile. The plant concentrates were a gold ore with 128 g/t Au of which 8% was non-refractory and a zinc concentrate with copper impurities.The gold concentrate showed complete dissolution of the gold bearing minerals after milling giving almost complete gold liberation. The zinc concentrate showed almost all of the sulphides had solubilized leaving the gangue and elemental sulphur. A study of pure pyrite and arsenopyrite shows that selective dissolution should be possible by a simple leaching process directly after milling.The milling of ilmenite and coal together results in a temperature decrease of 150°C in the subsequent carbothermic reduction of ilmenite, in addition to improving both the rate of reaction and the selectivity of reduction to rutile. IntroductionAlmost all mineral processing plants use mills for the size reduction of particles prior to physical and chemical processing. When continuing beyond size reduction the energy transferred causes deformation, breakage and realloying of particles giving a steady-state particle size. The breaking also causes increasing damage to the crystal structure by formation of smaller grains giving an increasing number of grain boundaries and increasing crystalline defects due to deformation. The increasing number of grain boundaries and defects leads to increased reactivity, which can be seen directly by a reaction within the mill, or indirectly, via a decrease in the subsequent annealing temperature required for reaction."

Jan 1, 1997

By Robert J. Uffen

YOU will likely recall the accomplishments of the International Geophysical Year of 1957, with its polar expeditions, the discovery of the Van Allen radiation belts and the spectacular launchings of the first artificial earth satellites. Our know ledge of the exterior of the earth was greatly increased by this international, friendly, cooperative scientific investigation. The Inter-national Union of Geodesy and Geo-physics has now been joined by the new International Union of Geological Sciences in sponsoring a similar study of the earth's interior. The program will extend from January, 1962 until December. 1964, and is known as the International Upper Mantle Project. During the T.G.Y studies of the interior of the earth were relatively neglected, even though the same international •Cooperation in obtaining simultaneous world-wide observations, by similar instruments, is required to locate and study earth-quakes, for example, as it is to study the earth's upper atmosphere. The upper mantle is 1•emote from man, as it extends from a depth of about 10 km. to perhaps 1000 km., but its practical importance is great.

Jan 1, 1962

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By B. A. Monkman

"IntroductionONE OF :THE most effective methods by which the construction industry is combatting mounting building costs is by making increased use of lightweight materials, thus reducing the dead load to be carried •by structures. This applies to non-metallic materials as well as to metallic ones, and particular attention has been given to developing lightweight aggregates for use in concrete.The use of lightweight aggregates is not new and, in fact, dates back to the Roman Empire, when pumice was used in the walls and domes of the Roman buildings. More recently, and up to a decade or so ago, the demand for these aggregates was met from deposits of volcanic cinders, pumice, scoria, etc., and from the by-products of blast furnaces and coal burning boilers. However, these sources of supply are no longer sufficient to meet the demand, for transportation costs pretty well restrict the use of the natural lightweight aggregates to the western cordillera regions where the deposits of these materials occur, and the use of expanded slag aggregates to the areas neighbouring the plants where slags are produced. As for cinders, the supply has been greatly reduced by the conversion of industry to fuel oil, natural gas, and powdered coal, and the large stockpiles which existed previously have been pretty well exhausted.Industry's approach to the problem of a decreasing supply, in the face of an increasing demand, has been characteristically direct. The solution has been to construct plants whose sole .purpose is to produce economically an acceptable light-weight aggregate from materials close at hand."

Jan 1, 1955

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By G. T. Lapidus, R. Zárate-Gutiérrez

Selective leaching of lead from a Pb-Ag-Zn concentrate with hydrogen peroxide in citrate solutions was studied at room temperature. Leaching tests were performed, varying the H2O2 concentration and the solid-liquid ratio, holding the solution pH constant at 7, and the citrate concentration at 1 M. Lead extractions of 100 % were achieved with 4 and 5 times the stoichiometric quantity needed to form elemental sulfur, with only a small amount of metal impurities dissolved (Ag, Zn and Fe). The lead solubility limit at those conditions was found to be ~21 g L-1. X-ray diffraction analyses of the leach residues were free of galena (PbS), while other metal sulfides, such as sphalerite (ZnS), chalcopyrite (CuFeS2) and pyrite (FeS2), were basically unaffected.

Jan 1, 2014

By D. F. Coates

Slope problems arise on mining properties from cuts for roads and railroads and from open pits. When it is 'realized that 1,000,000 extra tons of waste may have to be mined as a result of an average slope being reduced by 1 ° it is easy to appreciate that the slope problems connected with open pits are of far greater importance than the others. The type of slope failure that can occur can be classified in different ways. The most useful classification would be one that separates the causes in such a way as to provide a basis for studies to deal with problems of prevention and control. Using this criterion the types of slope failures are classified into four groups. Having classified the problems in this way an understanding can be gained of the various mechanisms involved in failure ..

Jan 1, 1961

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By K. Soldenhoff, D. Wilkins, E. Ho

In the processing of rare earth ores, a pure, mixed rare earth chloride solution is usually produced and used as the feed to solvent extraction circuits to separate the individual rare earths. Cerium(III) may be separated from the other rare earths by oxidising it to cerium(IV), which precipitates as cerium(IV) hydroxide in chloride liquors. This oxidation step may be inserted either before rare earth separation by solvent extraction or between solvent extraction circuits. Although oxidation of cerium by sodium hypochlorite has been known for many years, detailed conditions for oxidation are not readily available. The effect of hypochlorite addition, temperature, pH and cerium concentration on oxidation of cerium(III) from synthetic solutions was investigated

Jan 1, 2014

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By F. L. Thompson

MAN has been using lubricants of one type or another for at least four thousand years, and probably for a much longer period. We have learned from the inner wall of the tomb of Tehuti-Hetep, on which is a decoration illustrating the method of moving a great stone statue, that as early as 1650 B.C. lubricants were used to facilitate the movement of heavy loads. The Egyptians had available nearly every animal oil and fat, as well as at least thirteen vegetable oils, of our time, all used for food products and in the arts. Examination of the deposit on the axle of a chariot from an Egyptian tomb of 1400 B.C. showed it to consist of animal fat, quartz, sand, iron, and compounds of aluminium and lime-indicating a manufactured lime-soap grease made with lime-soap and possibly tallow. This would not be a bad lubricant for the axles of chariots which had to travel over sandy soil in hot weather. As to the method of grease application, it is remarkable that, from the time wheels were first used in the far distant past up to the present day, no one has ever thought it necessary to design a seal to keep the lubricant in and the dirt out. While time certainly marches on, we have today, in waggons throughout the world, exactly the same form of lubrication as was used in the earliest chariots. From the early days of the chariot until shortly before 1800 A.D. (when the steam engine was introduced), the main heavy equipment required for mining purposes, for machines of war, etc., was made of wood. The bearings were rough, but usually they had metal in the lower half. Light machinery was made of bronze, brass, or iron. Large clearances and poor alignment, plus the fact that speeds were much below present-day demands, combined to provide conditions that were quite satisfactorily met by the lubricants available. These were often produced locally by the machine operator. In northern countries, lard oil, prepared from the fat of hogs, was the universal lubricant employed in machine shop, as a belt and leather dressing, and for cutting operations. Sperm oils were used for light machinery, whereas beef and mutton tallow were more generally employed for the largest bearings. For the early steam cylinders, a slug of heated beef tallow was injected wherever the cylinders gruntingly complained of a lack of lubricant. Southern countries, however, resorted to the use of vegetable oils-olive, cocoanut, etc.

Jan 1, 1940

By A. Galley, R. Tosdal, F. Robert

The Canada Mining Innovation Council (CMIC) Exploration Innovation Consortium developed a 10-year business case for developing new discovery criteria, exploration techniques, and better data management and analysis to improve exploration success in deep, remote, and covered terrains. Within this context, the CMIC devised a five-year project proposal to create improved multiparameter exploration tools to detect ore systems and more efficient vectoring toward high-grade mineralized cores. The Footprints project was approved March 2013. More than CAD$13 million funding was provided through the CMIC-led joint sponsorship from 30 companies and the Natural Sciences and Engineering Research Council. Consistent industry leadership and integration of dedicated industry and academic expertise has the project on track for reaching its well-defined objectives.

Jan 1, 2014

By K. Hambrice, E. Fauveau

"When it comes to measuring the level of bulk solids, liquids, and everything in between, guided-wave radar technology now offers more level-detection capabilities than ever before. For an ever-widening range of previously hard-tomeasure products such as molten sulphur, liquid ammonia and petrochemicals, guided-wave radar transmitters provide accurate level measurements even under harsh chemical environments, wide variations in operating temperatures and pressures, and low dielectric constants.Great strides have been achieved in making these units easier to configure to a variety of process applications coupled with the simplicity of integrating these devices with most digital communication protocols. These improvements come as welcome relief to process engineers within an expanded range of level applications across several different industries that seek solutions to measuring the contents of tanks, silos, hoppers, bins, mixing basins, and vessels.Because radar transmitters have no moving parts, radar has already established a dominant niche in level measuring that quickly distances itself from mechanical means, which do not hold up as well in dirty service. Radar achieves its nonmechanical level detection capability by measuring the time of flight of the transmitted signal.Known more accurately as time domain reflectometry (TDR), the process involves sending microwave energy down into a vessel. When the pulse of radar energy reaches the product (indicated by a change in impedance), part of the pulse is reflected back toward the transmitter.A receiver measures the exact duration of time between the transmitted and reflected signal — the “time of flight.” The device analyzes this time and ultimately displays the level of the product as a distance in feet, metres, or other engineering units."

Jan 1, 2003

"Syncrude Canada Ltd. operates one of the largest surface mines in the world. The mining operation has two distinct phases: (1) the removal of the overburden, utilizing trucks and shovels; and (2) the mining of oilsand with drag lines and bucketwheels. Both phases combined move approximately 330 000 BCM per day.In support of current production demands and to provide a contingent oi/sand source, Syncrude has developed an Auxiliary Production System (APS) supported by the truck and shovel operation. This system utilizes oilsand sources within the existing mine area on an as-needed basis.The recent increased capabilities of the processing plant to handle a larger volume of oilsand has increased the reliance of the APS system. To facilitate the increased capacity, an auxiliary mine was developed external to the Base Mine operation with a production capacity of4.7 MBCM of oilsand per year.Development of the Northwest Auxiliary Pit began in January 1990, with the first cubic metre of oilsand taken to the plant in June, 1990. The Auxiliary Pit, as designed, has a total ore reserve of 68 MBCM of oi/sand."

Jan 1, 1993

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By Norman Orr, J. W. Gregg, Jack Wahl

The Pembina Cardium pool is a low permeability, stratified, solution-gas drive reservoir. Water-flooding has proven to be an effective means of pressure maintenance for all areas of the pool in which an economic rate of water injection can be maintained. The majority of water injection wells in the pool are converted oil well~ with capacities greater than 100 millidarcy-feet. If the average injection rate per unit of capacity can be in-creased the lower capacity areas of the pool can be economically flooded. Theory, laboratory work, and two . early miscible-flooding projects with-in the pool suggested that average water injection rates for converted wells could be increased two to three-fold by the initial injection of natural gas liquids and natural gas. How-ever, these two early projects received volumes of natural gas liquid!:' and high-pressure natural gas which would be economically prohibitive for routine stimulation. Area D, one of the Five-

Jan 1, 1962