Search Documents

By Charlie Jefferson

Main Goal: Resource Assessment 1. Incorporate existing data & results, old process. 2. NEW Quantitative Analysis (Chung and Chen) 3. Try mass balance of U and geochemical tracers 4. Use holistic process approach ?with key foci ?Targeted basin / belt assessments ?Is there as much in the Athabascaas they say? ?Athabasca reference for other basins (Thelon, etc) ?Compare sandstone & volcanic with USA, Kazakhstan etc: do their models apply here? ?Which IOCG systems are prospective for uranium? 5.Consider Groundwater, Environment; 6.Communicate

May 1, 2006

By Hyumng Sup Choi

The role of the interfacial electrical 'Condition on the adsorption of col-lectors on mineral surfaces has been studied by electrophoretic mobility and adsorption measurements made on zircon. From the investigation of the electrokinetic properties of zircon, H+ and OH-are seen to act as potential determining ions, thus controlling the electrical nature of this mineral. The isoelectric point of zircon occurs at a pH of approximately 5.0, and it is evident, therefore, that the zircon surface would be positively charged below a pH of 5.0 and negatively charged above this pH. The adsorption of collectors therefore de-pends strongly on the pH of the solution; anionic collectors are adsorbed on positively charged surfaces and cationic collectors on negatively charged surfaces. This, in turn, de-fines the effective flotation condition, with respective collectors, for this mineral. The above results have been correlated with the flotation behaviour obtained by the simplified flotation test using a modified Hallimond tube.

Jan 1, 1963

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By W. de Klerk, M. B. Thorpe

Golden Star Resources Bogoso operates in Ghana’s Western Region. The gold recovery plant includes; a flotation circuit producing a concentrate for the BIOX® process that oxidizes sulphides before a CIL circuit; and a dedicated CIL circuit. BIOX® uses bacteria, therefore water from the BIOX® and CIL plants remained separated; CN water could not be introduced into the flotation / BIOX® circuit. The operation built a process water inventory with high TDS and installed a process water treatment plant (PWTP). Water was released in compliance the permits but containing some thiocyanate. The PWTP brine was returned to the TSF, further exacerbating the TDS. The operation experienced a drought removing the traditional water sources; the team evaluated the options to maintain production - various water streams were laboratory tested provided options for water use. The paper presents the story (treatment chemistry and process chemistry) of continued operations by treating stored water and PWTP discharge water with peroxide; brine usage within the CIL circuit, which increased gold recovery (laboratory testing) and reduced the TDS. Water flows were further modified to include hydraulic tailings re-mining to a CIL circuits. Details of the recovery, basic chemistry and costs savings are provided.

Jan 1, 2014

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By James H. C. Martens

Among the many interesting problems of the pre-Cambrian of the Canadian Shield is that of the origin of certain types of gneisses which are intimately associated with the granites on the one hand and with the metamorphic rocks of known sedimentary origin on the other. The observations recorded in this paper on the structure and composition of these ancient rocks found in a small part of northern Quebec may help to lead to a clearer understanding of the way in which they were formed and also constitute a contribution to the regional geology and petrography of a district for which little detailed information is available. The area considered is located near the Ashuapmuchuan, or Chamuchuan, river about 180 miles north-northwest of the city of Quebec, and therefore well within the Canadian Shield. Although most attention was devoted to the rocks along this river from the 57th to the 70th mile above its entrance into Lake St. John, a few observations on other localities to the north and northwest of that lake will be included. The field work was done in the summer of 1924 in cooperation with L. W. MacNaughton, E. S. Roberts, and B. M. Shaub, all of Cornell University. The party ascended the Ashuapmuchuan river by canoe and spent about a month near the mouth of Stacker, or Brochet, river, the outlet of the lake of the same name, returning by way of Mikoasas river. The writer wishes to express his obligation to his associates for their co-operation in the field and for their permission to publish the results. He is especially indebted to B. M. Shaub for the photographs of rock outcrops. Professor A. C. Gill g:ive many suggestions which were helpful in the laboratory study of specimens and in the preparation of this paper.

Jan 1, 1927

By Marcel Allard

On January 1st, 1977, SIDBEC-NORMINES INC. purchased from Quebec Cartier Mining Company various facilities located at Gagnon and Lac Jeannine together with the Fire Lake deposit. A t the same time, SIDBEC-NORMINES started its mining operations at Fire Lake, 83 km northeast of Gagnon. The paper summarizes the various adjustments which were necessary to satisfy the new production conditions, such as the physical and mechanical properties of the ore at Fire Lake, and the new crushing and loading installations at the mine, together with the transport of some 14 million tons of crude ore to the Lac Jeannine concentrator about 100km away, and finally to achieve satisfactory recovery from the FireLake ore. In addition, mention is made of the manpower organization, in which Quebec Cartier Mining Company plays an important role as manager of operations and owner of the railroad linking the mining operations to the pelletizing operations at Port-Cartier.

Jan 1, 1979

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By J. J. Mather

NEPHELINE SYENITE is a feldspathic rock resembling granite in texture and hardness but it is white in colour and contains appreciable quantities of the mineral nepheline, the result of a silica deficiency. It is relatively common, with known occurrences in Russia, Scandinavia, India, Canada, United States, and other parts of the world. However, the particular deposit being mined at Nephton, Ontario, by American Nepheline Limited is unique in its remarkable uniformity and low content of iron bearing minerals, both qualities essential in a ceramic raw material. The orebody is a pear-shaped mass over five miles in length, up to a mile in width, rising in three prominent ridges as much as 300 feet above the surrounding lakestudded terrain. American Nepheline holdings, consisting of 2,200 acres, comprise some 85 per cent of the total mass.

Jan 1, 1957

By J. Dilbeck, J. K. Ratliff, T. Petrov, Z. Brown

"In efforts to improve dust control during deep cut continuous mining a supplemental atomizing spray system, mounted on 14CM15 continuous miner, has been designed and successfully implemented in a U.S. coal mine. The mine is 2.1 m (7-ft) high and uses a blowing curtain face ventilation system with 1.1 m (3.5-ft) curtain offset from the rib. The face ventilation design parameters were set to 9.4 m3/s (20,000-cfm); 4.2 m3/s (9,000-cfm) line curtain flow rate, and 3.8 m3/s (8,000-cfm) scrubber capacity. The performed in-mine measurements, before and after the implementation of the atomizing spray system, showed a significant decrease in the respirable dust levels at the operator place as well as at the return. The paper describes the supplemental water spray system design and performance supported by three-dimensional computational fluid dynamics (CFD) simulations and in-mine test data.INTRODUCTIONThe work on this project have started in 2015 with a study of the conventionally applied face ventilation layouts. The specific behaviour of the face ventilation system have been analyzed trough in-mine measurements and computer modeling of typical cut scenarios. An computer modeling methodology have been developed for estimation the respirable dust concentration (RDC) using tracer gas to RDC contour mapping, calibrated by a single point value, provided by in-mine measurement. Utilizing the results of this study the engineering staff of the mine designed and implemented a supplemental atomizing spray system to improve the dust control during the deep cut continuous mining. Today the atomized spray system is successfully applied demonstrating steady performance and a significant decrease in respirable dust concentration on the working places of the continuous miner (CM) and coal transporters (CT) operators as well as at the return air stream. Information about the applied type of spray nozzles provided by other researchers (Cheng, 1973; Dick et al., 1996; Organiscak & Page, 1998; Pollock & Organiscak, 2007) and spray system manufacturers (Spraying System Co, 2011–2018; Steinen Mfg., 2016) have been used in this project. CFD code and simulation approach validated in a study conducted in 2000-2014 have been applied (Turner et al., 2002; Wala et al., 2004, 2007; Petrov, 2014)."

Jan 1, 2019

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada's current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today's commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By Matthew S. Bingham, David H. Searle

"One of the most significant developments in environmental law has been the development of mandatory project review processes, at both the federal and provincial levels.FederalWhile, in the past, project review processes have, f or the most part, been spelled out in guidelines, the guidelines have not had the force of law. All that has changed, particularly at the federal level, with the Federal Court decisions commonly referred to as the Old Man River and Alameda and Rafferty Dam cases. These decisions, taken as a whole, are authority for the proposition that the Environmental Assessment and Review Process Guidelines Order, SOR 82-487 is a law of general application, not a mere guideline which may or may not be applied. This federal environmental assessment process first provides for a screening, and, depending upon the results of the screening process, the possibility of a public review. This federal process only applies, however, when the proposal is being undertaken by a federal department, or where the Government of Canada makes a financial contribution, or where federal lands are involved, or where a federal licence or permit is required.Bill C-78, the Canadian Environmental Assessment Act, will replace the Federal Environmental Assessment and Review Process Guidelines Order once it has been passed by Parliament. Currently the bill is being widely discussed, both between governments as well as public interest groups.ProvincialOn the provincial scene, there are three project review processes, one concerned with new mines, the second with energy projects and the third with all other major projects. The most recent initiatives taken by British Columbia are twofold. First, the Mine Development Review Process which was in the form of a guideline, has been replaced by the Mine Development Assessment Act. Second, the Major Project Review Process has been formulated and is to apply to four main categories of major projects:1. Pulp and paper production;2. Mineral smelting and refining;3. Chemical products; and4. Major ports and marinas.Energy projects are governed by the Energy Project Review Process which is legislatively mandated under the Utilities Commission Act."

Jan 1, 1991

Evolution of Maintenance Practices. Mechanization processes in underground mining operation became stronger in the 70?s - 80?s. Did maintenance practices changed over the years ? What are the the major differences of today?s practices? Speaker, Robert Hamilton Working at different positions into maintenance organization since over 25 years, Robert has accumulated a various and rich experience of ways to maintain equipment. He started as mechanic on construction projects and open pit mines. Early in his career Robert had supervision's responsabilities. He started in open pit operation (QCM) and after in underground operation with Lac Minerals, working at Bousquet, Doyon and Louvicourt mines, as U/G mechanical foreman and mechanical general foreman, and Maintenance superintendant with Cambior . He also experienced the underground mines equipments supplier's side working with Sandvik Canada.

Feb 1, 2008

By H. Blaha, H. Wagner

"Room and pillar workings in salt mines are preferred sites for underground waste disposal. A critical issue in selecting waste disposal sites is long-term behaviour of such workings. The long-term behaviour of salt pillars is controlled by the pillar geometry, i.e. the height, width and length of pillars and the level of pillar stress. The latter has a strong influence on creep characteristics of salt pillars whereas the width to height ratio of salt pillars determines the strength of pillars and the deformation characteristics of salt pillars.Three different regimes of pillar creep behaviour of salt pillars can be distinguished, namely a stress level below which the rate of creep approaches a value of zero, a stress range where the rate of creep is constant and finally a stress level above which the rate of creep accelerates. Long-term stability of room and pillar workings can be assured only when the pillar stress level falls within the first stress regime. Strength and creep tests on model salt pillars have shown that at stress levels below 40% of pillar strength the rate of creep approaches a value of zero, between stress levels of 40% and 65% the rate of creep is constant but increases with stress level. Above pillar stress levels of 65% the rate of creep accelerates.Long-term measurements of pillar deformation and surface subsidence above relatively shallow room and pillar workings in salt mines have confirmed these observations. Long-term strength of salt was found that be between 60% and 65% of short term strength. The evaluation of salt pillar behaviour on the basis of critical pillar stress levels was found to be superior to the traditional factor of safety concept because it allows relating pillar deformation measurements to actual pillar conditions. The approach described in the paper was used successfully to evaluate the stability of room and pillar workings in a salt mine and to design strategies to stabilise critical pillar workings."

Jan 1, 2015

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By C. D. Williams

The following paper deals with some of the aspects of the law as it relates to the oil and gas industry in the Province of Alberta, but it should be stated here that consideration of this large subject will be confined to discussion of only those laws, rules, and regulations which affect actual exploratory operations. The paper will not touch on those branches of the law which deal with such matters as income tax, customs, and other kind red subjects which are of a highly technical nature and which are more properly the field of the specialist. Generally speaking, any system of law consists of certain major components. There must be, firstly, a national authority capable of ensuring the existence of the state itself and of maintaining the stability and continuity of its institutions; secondly, a philosophy of government covering the relationship of the state to the individual and of the individuals to one another; thirdly, a body of law to effect the purposes of the philosophical principles; and, fourthly, a judiciary to arbitrate any disputes that may arise from such relationships. All of these components and the system itself are, of course, subject to a varying degree of modification with the changing times and with the influence upon them of other systems of law. Now. while it is true to say that all systems of law comprise these similar basic features, it is apparent that the end result of any two systems of law in their impact upon the individual may be quite different.

Jan 1, 1951

"Successive seismic waves may cause progressive weakening of a fault zone, which has been recognized as the mechanism of earthquake aftershocks. However, it is unclear that how a fault zone slips under each wave cycle and how slip displacement accumulates under continuous wave cycles. This laboratory study provides direct evidences on the slip process of a simulated granular fault zone dynamically induced by an incident wave without the effects of late-arriving and reflected waves. The experimental observations show forward and backward slip paths of the fault zone and partially recovered slip displacement after a wave incidence. The unrecovered slip displacement after each wave cycle can be accumulated until it reaches a critical slip distance for seismic faulting, which may reinterpret delayed triggering in earthquake dynamics. The limited interseismic period restricts fault self-healing in strength. The experimental results also indicate that the dynamically induced frictional slip on the fault zone is associated with a complex frictional system, including seismic wave radiation, frictional slip initiation and normal stress vibration. Different from the dynamically induced frictional slip on the fault zone, the statically induced frictional slip causes a permanent increase of slip displacement along the shear loading direction. INTRODUCTIONAn earthquake mainshock may induce aftershocks by suddenly changing external stresses applied to another fault zone in the near field (Kilb et al., 2000) and by slightly perturbing a fault zone from a critical steady state to stick-slip faulting in the far field (Gomberg and Davis, 1996). The dynamically induced frictional slip on a fault zone has been recognized as the mechanism of earthquake aftershocks (Marsan and Lengliné, 2008; van der Elst and Brodsky, 2010). Although earthquake aftershocks have been extensively studied by many seismological methods, a simplified laboratory fault zone can provide possible interpretation on real faulting and detailed analysis on a friction process (Dieterich, 1979; Nielsen at al., 2010). According to a few laboratory experiments related to the dynamically induced frictional slip on a simulated fault zone (e.g., Uenishi et al., 1999; Johnson et al., 2012), the slip process induced by successive seismic waves exhibits continuous motions. However, it is unclear that fault slip response under each wave cycle and slip displacement accumulation under continuous wave cycles."

Jan 1, 2015

By D. Brossman

"The virtue of spray drying is that it is a drying method, and so far the only one by which it is possible in one operation to divide a mineral concentrate into its basic primary particles.,In so doing, each particle gets the same treatment and the result is a dry concentrate more homogeneous than any other known concentrate drying process. This is particularly good for a flash furnace requiring a bone dry finely divided feed. The spray dryer also features a very short residence time and due to the very quick operation the solids are kept cool thus preventing any risk of fire or explosions on these pyrophoric materials.There are many spray dryers now in operation in the mining industry and one of the latest applications is in South Africa where a spray dryer is treating a copper-nickel platinum concentrate which is, after drying, fed toan electric arc furnace. Experience has shown that the concentrate should contain 4% moisture for the furnace, and this is achieved by drying the concentrate bone dry and then back-mixing with thickener underflow pulp to provide an extremely homogeneous feed to the smelter. As mentioned before, mixing with pulp would be more of an advantage because we would not be evaporating water which would have to be added again afterwards.One of the first spray dryers to go in was at Western Mining Corporation in Kambalda in Western Australia. (A series of slides was then shown)."

Jan 1, 1972

By A. Hayatdavoudi, K. G. Sawant, F. Boukadi

"In this work, we found that contact between shale and water results in development of micro fractures. Based on results of experiments on Pierre shale, we conclude that appearance of micro fractures begin with saturation of capillaries, ionic and diffusive transport of water into the shale clays and once capillaries are saturated, the cause of micro fracture propagation is the conversion of ionic activity/exchange to excess pressure that did not exist before fracking. Based on these findings, the spread of micro fractures appear to be a time-dependent phenomenon which has not been addressed in the existing macro/micro fracture models.INTRODUCTIONShale has often been involved as a hazard in drilling operations. This hazard can be defined as “destabilization” of shale. When contacted with water-based drilling fluids, some shales readily swell and sometimes, cause the wellbore to cave-in, slough, wash-out, close, and pack-off, impeding the drilling by sticking the drill-pipe. However, once drilling reaches the desired depth or length, the casing is set, cemented, and perforated, and then actually we wish to initiate fractures and destabilize the shale formation, using hydraulic fracturing.Clays constitute a major portion of minerals in shale. These clays contain a large amount of free energy which is the main factor for “slick” water adsorption/absorption. In fact, the reason for using “surfactants” in hydraulic fracturing fluids is to make the penetration of the fluid into the capillaries much easier, thus water meets with less resistance to enter the small capillaries. Also, the result of high capillary suction pressure is due to small Angstrom size capillaries, smaller pores and presence of ions and hydrateable metal atoms. The free energy is thus, related to all the above mentioned and other affects. Capillary pressure, osmotic pressure and other pressures are responsible for creating the micro-fractures in shale, thus, increasing the network of micro-fractures which leads to more gas production. The objective of this study is to evaluate the pressures of the individual ions which are released by the diffusing “slick” water into shale. These pressures would be added to the above mentioned capillary pressure, osmotic pressure, bacterially-induced pressures, chemically-induced reaction pressure, pressure due to exchangeable ion-transport, pressure due to release of free energy of solvation and eventually to the pore pressure as suggested by Terzaghi’s equation."

Jan 1, 2015

By N. Ahern, D. B. Dreisinger, G. Van Weert

In the thiosulfate leaching of gold, degradation of the thiosulfate reagent is a major cost. One of the intermediary degradation products is trithionate, which also inhibits gold recovery from solution by ion exchange. Little attention has been given to this species in the context of gold leaching - the limited information on trithionate and its solution chemistry available in the literature is seldom directly related to gold leaching conditions. This review is a compilation of the published knowledge on trithionate, with a specific focus on identifying the relevance of this information to gold leaching and the shortcomings in the knowledge base.

Jan 1, 2005