Search Documents

By D. B. Apel

As depths to the ore bodies keep increasing around the globe, the problem how to deal with the increasing temperature of undisturbed rock mass becomes very important. In extreme cases the rock temperature at the bottom of the mine could raise up to 80 °C. In deep mines, geothermal heat is considered as the primary heat load contributor, which accounts for 50?90% of the total heat load depending on different geological conditions. Thus the geothermal heat control in underground mines is the most important and demanding issue to ensure a suitable working environment. In this study, expanded perlite aggregate (EPA) was incorporated as a lightweight substitute for sand. Five mixtures were prepared using 0, 25, 50, 75 and 100% replacement ratios of sand by EPA. These, mixtures were tested in the laboratory for both the insulating and strength properties of the developed shotcrete. The goal of this research was not only to develop shotcrete which would exhibit good insulating properties but also which would exhibit strength properties similar to the regular shotcrete. This paper not only reports the results of the laboratory tests but also discusses the output of numerical model which was performed to evaluate the benefits of using the insulating shotcrete in reducing the cooling costs at hot underground mines.

Aug 1, 2013

By Roberto Pena, Cristhian Morales, Darwin Morales, Veronica Cambiaso

"This article makes evident the shortcomings of the current operation of oxygen pipes as well as the damages they cause and why they cause them. When focusing on the causes and effects of these drawbacks, it was possible to develop a new family of thermal lances that could pierce a taphole with the precision of a drill but with the capacity to complete the whole operation. Although efforts have been made to replace oxygen pipes since they are annoying, dangerous and inefficient, nobody had worked to improve the way the traditional oxygen pipe taps/perforates the furnaces and reactors tapholes. In fact, developments made in drills and robotic arms, have failed to replace the oxygen pipe, which despite their negative side effects have been used for more than a century. Observation and theory were key to radically transform this humble tool into a dependable and efficient support in the operation. A good news that it is worthwhile to share for the benefit of all of us, passionate about the world of pyro metallurgy.INTRODUCTION Normally, reports and papers prepared for conventions, symposia or other technical events related to metallurgy aim to relevant topics in the operational field, probably because in them lay the scale economies every company pursues. We intend to give relevance to a matter normally disregarded in operations, but that unmistakably vital: if the furnace or reactor cannot be bled, the pyrometallurgical process will not be completed. Besides, if the tapping task is difficult or is long delayed, the availability of the furnace will be reduced. Consequently, there will be a waste of energy and workers will be exposed to dangerous levels of radiation as well as to work overload and physical injuries Apart from these basic effects, in tapping operations where oxygen pipes are used, we can see serious damages in the smelting furnace, especially in the taphole components such as refractory bricks, taphole jackets and water cooled plates. This paper intends to show that taking care of the tapping task can significantly upgrade not only to the tapping operation itself, but also the whole plant productivity."

Jan 1, 2017

By J. F. Henderson

"IntroductionTHE National Advisory Committee on Research in the Geological Sciences was set up by the Privy Council of Canada in 1949. It was set up because you, the Geology Division of the Canadian Institute of Mining and Metallurgy, asked that it be set up. The Committee is, therefore, to a consider-able degree, your offspring. In the role of good parents you, of the Geological Division of the C.I.M., should be interested in the progress of your progeny. How is the Committee organized? What has it recommended? What has it accomplished? On behalf of the National Advisory Committee, that is what I want to tell you about this afternoon.HistoryYou will remember that, in 1946, the Geology Division of the C.I.M. set up a Committee on Geological Research. This Committee, under the Chairmanship of Dr. J. E. HAWLEY, found ""that there is no national organization interested in surveying, co-ordinating, and implementing with financial help, fundamental and much needed geological research. Accordingly, the first and most necessary step to put the geological sciences in Canada on a proper footing .is the recommendation that a National Advisory Committee on Research in the Geological Sciences be formed"" (l).This recommendation was endorsed •by the President and Council of the C.I.M. in 1947 and submitted to the Minister of Mines and Resources."

Jan 1, 1952

By Raj Thamburaj

"Over the last few decades, the emphasis on affordability and reduced cost of ownership has necessitated the development of innovative processes to carry out repairs in aero engine components. Conventional weld and braze repairs have evolved into advanced, sophisticated processes using state of the art knowledge in lasers, robotics and materials technology. This paper illustrates past and present scenarios in an attempt to illustrate progress that has been made in this area. The problems encountered in the past have been detailed along with the solutions that have been developed and commercially implemented to address these issues. Apart from technical progress, this presentation also addresses the progress made in business approaches and in Certification/Regulatory issues surrounding aero engine repair. Progress in Technology Repair technologies have also been the embryo from which new and revolutionary manufacturing technologies have evolved as well. Electron Beam Free Forming and LENS are examples of how a completely new manufacturing concept can evolve what was originally only a process to join metals. The current and future potential of these spin offs is discussed providing examples of application. While several problems have been solved over time with the implementation of advanced repair technologies, the demands of the industry have created new challenges. The paper describes these issues, outlines potential solutions and discusses the future of repair technologies in terms of the far reaching influence it is sure to have in design, manufacturing, maintenance management and life extension. Progress in Business Trends.Business approaches to repair and maintenance have also gone through considerable change with the introduction of ""Power by the Hour"" and other similar arrangements between the companies responsible for engine overhaul and the end-users. Program Based Logistics (PBL) is yet another innovation to provide a win-win situation for the repair service provider and the end user. This paper traces the development of these business initiatives and highlights successful applications. Progress in Repair Certification, Regulatory Issues.Understanding of the issues surrounding certification of repairs has also evolved with time and regulatory issues have been clarified considerably. Procedures for analysis and testing are much clearer and ""Check Lists"" are being drafted for certifying repairs on various engine components. The PMA phenomenon has added yet another dimension to the issues regarding certification and these are discussed as well."

Jan 1, 2010

By F. Azgomi

A possible way to characterize (classify) frothers using gas holdup as a surrogate for bubble size was explored. Nine surfactants with a range in chemical structures were selected and tested in a bubble column instrumented to measure gas holdup and superficial gas velocity. A correlation between frother type and gas holdup was observed: for alcohols, gas holdup increases with hydrocarbon chain length and the effect is the same whether the chain is branched or straight; for polyglycols, gas holdup increased with number of propoxy groups. The ranking by gas holdup gave the same result as other frother characterization techniques.

Jan 1, 2006

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924

By M. E. Holter

"Five main lignite seams occur in the Tertiary Ravenscrag Formation in the Eastevan area, at depths of 100 feet or less. They are named, in ascending order: the Boundary, Estevan, Souris, Roche Percee and Short Creek seams. A total sequence of approximately 250 feet is represented by the coal beds and interstratified clays, silts and sands. Strata dip to the southeast at 25 feet per mile or less and trike northeast. Large areas underlain by coal seams at shallow depths are delineated. Reserve calculations are dependent on detailed information on seam thicknesses and feasible stripmining depths. The stratigraphically higher seams are thinner on the average than lower seams and this, together with the increase in elastic size fractions in higher strata, suggests a retreat of a Tertiary marine margin to the south during the closing depositional history of coal seams and associated strata."

Jan 1, 1972

By D. Kong, A. Klyashtorin, L. McGilp, I. Wilson

This work reports on applying iron oxide coated sands media in an experimental permeable reactive barrier to remove uranium species from uranium containing water. A field experiment was conducted at the legacy Gunnar uranium mine & mill site that was abandoned in the 1960s with limited to no decommissioning. The flooded Gunnar mine pit presently contains about 3.2 million m3 of water contaminated by dissolved U (1.2 mg/l), Ra-226 (0.4 Bq/l), and minor concentrations of other contaminants (As, Se, etc.). The water is seeping over the pit rim into Lake Athabasca posing environmental and health concerns. Iron oxide coated sands can be used to immobilize uranium species through an adsorption process. Methods for preparation of hydrous ferric oxide sorbents and their supported forms onto silica sands are described. Fourier transform infrared spectroscopy (FTIR), and powder X-ray diffraction (pXRD) were used to characterize the physical-chemical properties of the sorbent. The monolayer uranium uptake capacity (Qm) was estimated through the Langmuir adsorption isotherm. Adsorption kinetic experiments were performed in a lab environment before moving to a field trial. Based on these lab results and the input on field-scale appropriate geometries, a pilot permeable reactive barrier was fabricated and a field test conducted near the Gunnar pit in June 2019. This pilot test provided technical data and information needed for designing a full-scale permeable barrier based on the iron oxide coated sands, which may be applied for in-situ water treatment at Gunnar and other legacy uranium sites.

Jan 1, 2020

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By M. Yavuz

As a branch of Operations Research, decision making is a widely used application in both science and social sciences. There are many different methods developed to solve decision making problems in the literature. In this study, Fuzzy Analytic Hierarchy Process (AHP) method is performed for the selection of reclamation project selection in an open pit mine and the optimal solution of the problem is investigated. Different reclamation project alternatives are prepared for an open pit mine, which continues to its production activities in magnesite sector in Turkey. The data obtained from Magnesite Cooperation is used in the application of the method. A decision-making process is prepared as considering the project alternatives for the purpose of selecting the most suitable reclamation project. The entire criteria that affect the decision-making process are identified and transformed into a hierarchical structure. The problem is solved by using Fuzzy AHP method developed according to this structure. It is found that Fuzzy AHP is a method that may help decision-makers in solving different decision-making problems in mining.

Aug 1, 2013

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

By V. Vorontsov

Catalysts Mo-Ni-S were prepared by combining MoS2 and NiS in weight ratios 1:1, 1:2, 1:4 and 2:1, each of which was admixed with 5%wt Ag and 5%wt YSZ to increase three-phase boundary surface area of the electrode. For comparison catalysts comprising Co-Mo-S in weight ratio of 1:1 of CoS to MoS2 admixed with 5%wt Ag and YSZ and pre-sulfided NiMoO4 were made. The catalysts were examined for electrochemical oxidation of hydrogen sulfide in solid oxide fuel cells (SOFC) at 850°C temperature. The catalyst prepared from 1:1 (wt. %) NiS:MoS2 demonstrated highest performance. Current density up to 1,330 mA/cm2 and power density up to 300 mW/cm2 were achieved using pure H25 gas, which are the highest among the reported H2S-powered fuel cells ever published in the literature. Anode materials of different NiS:MoS2 ratios have been characterized by means of X-ray diffraction (XRD), simultaneous TG/DSC analysis and Neutron Activation Analysis (NAA). TG/DSC and NAA results show that addition of NiS and Ag increases fuel cell performance due to improved structure/integrity of the anode. It has also been demonstrated that MoS2 is a suitable anode material in H2S-powered SOFC, with high activity towards H25 oxidation and thermally and chemically stable up to 850°C.

Jan 1, 2005

By A. Vervoort

The concepts of geostatistics are commonly difficult to understand for students, even for those with a strong mathematical background. A main problem is certainly the link between the variation of the parameter value in space or time, and the calculated experimental semivariogram as a function of the interdistance, but over the entire area. Another problem is to differentiate between directional and omnidirectional semivariograms and the way they have to be interpreted. Furthermore first time users of geostatistics often do not want to struggle through different books with the whole geostatistical background before using it. Too often this leads to using geostatistics as a black box with all the risks linked to it. That is the main reason that we developed some interactive tools based on the free public domain software R. We aim by developing three different modules to assist individual first time users, but also regular students and teachers to get a feeling of the importance of the various aspects in conducting a good geostatistical study. The modules show directly e.g. the impact of deleting, moving or adding data points, of changing parameters of the semivariogram model and of the geometrical parameters during kriging. The first module allows making the link between the variation of the parameter values in one direction and the calculated experimental semivariogram, and this for different given datasets. The second module covers two dimensional datasets and apart from calculating the semivariogram values, models can be fitted to the calculated data. A distinction can be made between omni-directional and directional semivariograms, including the effect of the tolerance on the angle and lag-distance. The third module focuses on ordinary kriging of point values in two dimensions. The aim of the interactive tools developed is limited to educational purposes only, i.e. to visualize some basic concepts for different pre-selected types of spatial variation. They do not intend to do a geostatistical study on a certain dataset (for this purpose there exists already a broad spectrum of good software packages). The original intention of developing the three modules was aimed at users with no or a limited amount of geostatistical experience. However, these modules seem also very useful to remain critical for experienced users. One should never forget that in a real application one does not have a complete view of the phenomenon studied. The geostatistical interactive modules can be accessed through: www.bwk.kuleuven.be/geostatistics . We compiled a manual to facilitate the use of the modules and to guide the user we formulated several questions to be solved for each module.

Aug 1, 2013

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By L. Haavanlammi

Iron is a significant component of all copper concentrates leached in the HydroCopperTM process. The metals in the concentrate are leached in a chloride solution by oxidation with cupric ions. Copper enters into the solution as a cuprous chloro¬complex. Iron dissolves at the same time in the ferrous form, but it is immediately oxidized to the ferric state. Oxidation is effected by sparging air or oxygen into the leaching reactors. Because the pH is 1 - 2.5, ferric ion precipitates as akaganeite (T<90°C) or hematite (T> 90°C). Arsenic, antimony and the main part of the bismuth co-precipitate with iron and report to the leach residue. Cupric leaching is faster than iron oxidation; thus, leaching of low-iron concentrates (secondary copper minerals) is quicker than leaching high iron concentrates (chalcopyrite). Pyrite does not dissolve during copper leaching, but is oxidized slowly at higher redox-potentials after the copper has been leached.

Jan 1, 2006

By D. F. VanDine

The phases of a typical exploration program for sand and gravel resources include: (1) collection and assessment of existing information; (2) air photo interpretation and remote sensing; (3) ground investigation and mapping; (4) sampling and testing; and (5) data storage, retrieval, analysis and presentation. Depending on the purpose, time frame and funding available for the study, these phases, and the various techniques used within each phase, will vary. Once a sand and gravel deposit has been located, defined in size and quality, and found to be suitable for a given purpose, it can then be classified as a granular resource.

Jan 1, 1984

By R. D. Brown

"Taxation tends to be a depressing subject. Taxes are unfair, taxes are too high and, above all, taxes are too complicated.In a recent address to the Canadian Tax Foundation, the author discussed in a rather more lighthearted way the possible causes of the complexity of the present Canadian taxation system. In order to provide an element of relief in this series of articles on taxation matters, extracts from these remarks are quoted below :"

Jan 1, 1976

"Liberation is a key requirement for efficient separation in mineral processing. As a consequence of this an understanding of the inherent textural features of an ore is no longer possible since during the process of liberation, texture is destroyed. Knowledge of key textural features, such as mineral grain size and distribution, prior to breakage processes provides the opportunity to understand the textural drivers for ore hardness. Modern characterisation methods, including automated SEM-based techniques, provide the possibility of measuring mineral characteristics at a range of scales. This paper discusses how textural features of two different ore types in a porphyry copper deposit can be measured and interpreted at a number of scales. Standard breakage tests conducted on the ores indicate that one of the ores can be characterised as hard and the other as soft. The impact of mineral grain size and the presence and scale of vein type structures in the two ores have been used to determine the extent to which these features influence ore hardness.INTRODUCTIONIn order to effectively convert ore into metal, knowledge of both the processing stages and the characteristics of the ore are essential. Prior to the advent of technologies that enabled the fundamental understanding of the sub-process at each stage of processing and the measurement of appropriate ore properties the most effective way to understand how an ore would respond to a process was to put it through that process, for example the way to determine how an ore would break was to first break it. Existing comminution models seek to predict the size distribution of rock fragments as the result of applied energy based on knowledge of the rock strength. It is common for these models to consider the rock as homogeneous and despite providing important data for the design and optimisation of industrial comminution circuits these models are only applicable within a narrow range of operation. In order for reliable predictive models to be developed that account for the inherent ore characteristics, a step change is required in the type of measurements that are carried out to characterise an ore and the type of data that is extracted and used as model inputs."

Jan 1, 2016

By W. B. Agocs

"AbstractThe airborne magnetometer data of the Marmora iron ore deposit at Marmora, Ontario, have been used as an example to show the mapped results obtained by the use of line spacings of from 1 mile to 14 mile. The maps are illustrative of the results which could be obtained from such line spacings for any type of geophysical survey, and they show the probability of 'missing' a feature of economic value if the line spacing is too coarse.The probability equations are given for the crossing of randomly oriented features whose maximum dimension is less than the spacing of the control lines for circular, elongate, and rectangular outlines. The equations are P = D/S; P = 2L/S; P = 2(L+W)/,.S; P = A/,.S; P = (2L(S+T)-L2),.ST; and P (D(S+T-,.D)) ST, respectively; where P is the probability; D is the diameter; L is the length; W is the width; and S and T are line spacings.IntroductionTHE EFFECT of station spacing, and the effect of the distance between the plane of observation and the plane of the source of the potential field anomalies, have been studied by geophysicists in the past.The purpose of this paper, however, is to illustrate the effect of line spacing •on the resultant mapped magnetic anomaly for a known magnetite mass, and to present the elementary probability equations for determining the optimum control spacing for detecting a particular type of feature. The effect of line spacing which is illustrated by the magnetic maps presented herewith would be comparable to results which would be obtained by any geophysical survey, since the contours between lines are of necessity interpolated."

Jan 1, 1955

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005