Search Documents

By J-S. Marois, F. Cappucitti, Y. Dodier, D. Downey, G. Matton

"The flotation processes of the Niobec Mine have been affected by a seasonal loss of recovery and a significant increase in reagent consumption over the past few winters. This paper discusses the problem-solving methodology that was used to identify the root causes, to develop solutions and to implement changes that resolved the problem to restore the process to summer-like conditions year-round. Mainly, it was found that the process water was contaminated by phosphates ions, which adversely affected the carbonate pre-flotation, and caused detrimental effects on the subsequent niobium flotation. The phosphate ions were being generated by the process itself, but were consumed by algae in summer conditions. It was determined in laboratory studies that concentrations as low as 5 ppm were enough to affect the circuit and that the multiple additions of process water throughout the circuit was worsening the effect. Also, temperature was found to have an impact on the reagent performance. The performance of the plant was restored by implementing a natural treatment of our process water with a simple cost-free rearrangement of our circuit streams. In addition to that, our extensive geometallurgical program was used to provide ore to the plant restricting phosphate generation in the process. Also, a modification of the collector was developed and introduced in the carbonate pre-flotation that provided improved performance during the periods of low pulp temperature.INTRODUCTION Niobec is one the three major global producers of niobium presently in operation. Situated in the Saguenay-Lac-St-Jean region of Quebec and in operation since 1976, the site produces ferroniobium (FeNb) to be used mainly in High Strength Low Alloy (HSLA) steel, which is known to have better mechanical properties than carbon steel. The Niobec operation consists of an underground mine, a concentrator and a converter plant. The concentrator concentrates niobium-bearing minerals, mainly pyrochlore and columbite, to produce a high-content Nb2O5 concentrate which is then converted to FeNb in the converter plant by an aluminothermic reaction. The Niobec concentrator flowsheet, which has gone through many expansions and optimisation over the years, consists of grinding, desliming, flotation and leaching steps. The flotation steps are numerous, sensitive and difficult to operate due to the non-selective nature of oxide mineral collectors. Thus, the pyrochlore concentration process at Niobec still faces many challenges and is constantly going through periods of continuous improvement."

Jan 1, 2018

By K. Ilankoon, I. M. Saman, S. J. Neethling

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behaviour is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. The particle properties such as size, shape and porosity are very important when modelling the liquid holdup and flow within heaps, since the dominant mechanisms at work are quite different. This paper investigates the effect of these particle properties experimentally on heap flow behaviour using a 1-D column leaching system consisting of non-porous glass beads with a system of actual ore particles. The similarities and differences between the two systems on flow behaviour are described using an inter-particle flow model. In addition, the applicability of positron emission particle tracking (PEPT) for laboratory column leaching will be detailed to calculate hydrodynamic dispersion in packed beds compared to more conventional residence time distribution (RTD) tests and also to obtain the time averaged rivulet flow paths through the particles of the bed for the better understanding of heap hydrodynamics.

Jan 1, 2014

By J. O'Leary, R. Cannell, D. Honsberger

"The Scully Mine deposit lies within the group of metasediments that together comprise the rocks of the Labrador Trough. The ore itself still retains the bedding characteristics of the parent rocks and on this basis has been divided into three main members, namely: Upper, Middle and Lower. The Upper and Lower both show many of the bedding characteristics of the cherty taconites of the northern U.S.A.; the Middle member is a coarse-grained friable specularite rock. The ore minerals are hematite (normally present in the specular variety) and magnetite, although the latter rarely occurs in concentrations greater than 20 per cent. Gangue minerals are quartz and the hydrated iron oxides. Manganese oxides also occur as accessory minerals. The outcrop area of the orebody is in excess of 2 square miles, displaying a complex pattern of faulting and folding, which has been formed as a result of at least two orogenic periods."

Jan 1, 1972

By G. Forté, R. Girard

The Alcan Bayer Process Experimental Centre (BEC) is an essential development tool for the Bauxite & Alumina researchers at the Alcan Arvida Research and Development Centre in Jonquiere, Quebec. Between the laboratory tests and the industrial prototypes or the industrial applications, the BEC is a key element for technology transfers. The Bayer process is the extraction of aluminium oxide (or alumina) from the bauxite ore. The Bayer Experimental Centre's history and flowsheet are presented. The major pieces of equipment are described. Safety and design considerations are presented. Finally, examples of applications, double digestion and pressure decantation, are briefly described.

Jan 1, 2004

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy, E. D. Shepeta

This paper studies the features of known and newly synthesized dialkyldithiophosphates and reagents with thioamide groups when separating copper-containing and arsenic-containing minerals in the flotation of skarn-scheelite-sulphide ore at the Primorskaya concentration plant. The optimization of dialkyldithiophosphate collectors was based on the study of their surface activity at the liquid-gas interface and estimated hydrophobic abilities. The flotation experiments show that the selectivity of action of the reagent increases with an increase of its surface activity and a reduction of hydrophobic ability when separating chalcopyrite and arsenopyrite. IMA-225-5 was proposed as a more efficient dialkyldithiophosphate collector, which increases the recovery of copper by 2.8% compared to the industrially used collector IMA-I413. Selection of the optimal structure for reagents with thioamide groups (derivatives of thionocarbamate and thiourea) was carried out according to their acidity and the presence of hydrophilic particles in their structure. Calculations were performed depending on the pH of the solution of chalcopyrite to determine the optimum reagent sorption and to further optimize the structures of these reagents. The tests with reagents with thioamide groups show an increase in copper recovery by 3-4% together with a significant increase of arsenic content compared to IMA-225-5. As a stronger collector with thioamide groups, it was recommended to use sample 234, which belongs to the thiourea derivatives. IMA-225-5 was recommended for industrial tests at the Primorskaya concentration plant. Thus, this study has shown that using dialkyldithiophosphate is more appropriate if it is necessary to increase the selectivity of separation of copper-containing and arsenic-containing minerals, and using reagents with thioamide groups, or their combinations with dialkyldithiophosphates, is more appropriate if it is necessary to increase the recovery of copper or the quality of copper concentrate with less selectivity of the process.

Jan 1, 2016

By D. J. MacKinnon

"The Canadian Copper Company, formed in 1885, began mining the nickel-copper ores of Sudbury in 1887 and producing nickel-copper matte from its smelter in 1888(1). Although it was quickly appreciated that the separation of nickel and copper (i.e. refining) was critical to the production of a marketable nickel product, refined nickel was not produced in Canada until about 1918. From the beginning of the industry, there was considerable political agitation to refine nickel in the Province of Ontario(2). The companies, however, claimed that the existing processes, viz. the sodium sulphide ""tops and bottoms"" process operated by the Orford Copper Company of New Jersey, U.S.A.(1,3,4) and the carbonyl process(5,6) developed by the Mond Company at Clydach, Wales, were too costly to operate in Canada. Nickel was first refined in Ontario about 1918 when the International Nickel Company opened a nickel refinery at Port Colborne, Ontario(6). Initially, however, the refinery at Port Colborne employed the Orford sodium sulphide process, and the first electrorefined nickel in Canada was produced in 1920 by the British America Nickel Corporation whose mine and smelter were located in Sudbury, Ontario, but whose electrorefinery was located at Deschenes, Quebec, near Ottawa, Ontario. The purpose of this article is to outline the early history of nickel electrorefining and to trace the significant developments which led to the first successful commercial electrolytic nickel refinery in Canada. The development of an electrolytic process for refining nickel is due largely to the efforts of four individuals, viz. Carl Hoepfner, Hans A. Frasch, D.H. Browne and ultimately N.V. Hybinette, and the contribution of each is discussed separately below."

Jan 1, 1999

By R. Harrisson, K. Esmaieli

Brunswick mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance of ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions, etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Jan 1, 2008

By A. S. H. Kabir, I-H. Jung, J. Su, Yue. S., M. Sanjari

One of the major problems associated with conventional wrought magnesium alloys is the unwanted basal texture that forms during plastic deformation which generally does not change markedly after post-deformation annealing. Formation of precipitates on the recrystallized grain boundaries during annealing may affect the usual rotation of grains towards preferred basal direction resulting in texture weakening. In this study, Mg-Al-Sn alloy was hot compressed at 250°C and annealed at 350°C for various times. The initial as-deformed microstructure was partially dynamic recrystallized with dynamic precipitates on the grain boundaries. After annealing at 350°C, static recrystallization of the bimodal microstructure took place where at this temperature no static precipitates formed. The goal of this work was to study the effect of dynamic precipitation on the texture evolution during the annealing process. Texture evolution was studied during annealing by electron backscattered diffraction (EBSD) technique through a microstructure tracking process. It was found that precipitates on the recrystallized grain boundaries have significant effect on the usual rotation of the grains towards the basal direction, meaning significant texture weakening, which is beneficial for final mechanical properties.

Jan 1, 2015

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By \/eena Sahajwalla, Alexander Blagus

This paper reports the effect of using High Density Poly-Ethylene (HDPE)/coke blends on the reduction behaviour of Mn3O4 to MnO at 1000°C. The results suggest that CH4 release increases with increasing HDPE addition. The results show that the rapid release of methane, over only the initial five minutes, limited the interaction of Mn3O4/MnO with CH4. With the devolatilisation of HDPE there was increased porosity in samples containing HDPE, assumed to be the major factor in differences of reduction rates.

Jan 1, 2011

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Nowadays recycling became an important rare earth elements (REE) source, which allows to reduce their demand for extraction from natural deposits. At present, the used fluorescent lamps and old type TV or computer monitors kinescopes are selectively collected and undergo processing in the system of recycling. It has been estimated, that utilization of such waste would be sufficient to cover the REE demand for the next 5-8 years. In the developed process, the luminophores were separated from the electronic and electronic waste materials, and processed by hydrometallurgical methods to obtain concentrated REE in form of oxides. INTRODUCTIONInternational Union of Pure and Applied Chemistry (IUPAC) defines the rare earths as a set of seventeen chemical elements, specifically the fifteen lanthanides plus scandium and yttrium. They are considered the most important indicators of the developed technologies and techniques. Rare earths are used, amongst others, for the production of magnetic and superconducting materials, ceramics, lighting, catalytic converters, advanced electronics and alloys. The demand for RE continually increases, similarly to many other primary raw materials. Globalization, the growing demand for limited resources of raw materials, the policy of the countries controlling the raw material market and the economic crisis became a spur for new programs of socio-economic development of the European Union (EU), with particular regard to EU safety for commodities in intermediary as well as long-term horizons (COM 2008), COM 2011).EU countries import most of metallic and chemical raw materials important for their economy. In 2008 a detailed program named Raw Material Initiative was announced. The increase in demand for most raw materials having special importance for the development of technology, and access to of raw materials security of supply affect the future economies of the UE member states and other developed countries."

Jan 1, 2012

By Anita Marks

In 2007 Copper Mountain Mining determined that there were sufficient resources to consider reopening the Similco Mine near Princeton, BC. The mill facility that had been built by Newmont Mining in 1972 was closed in 1996 and all of the process equipment removed. The mill had been built on the west side of the Similkameen River to facilitate mining of the Ingerbelle Deposit. In 1980 construction was completed on a primary crusher and cable belt to deliver ore across the Similkameen River from the Copper Mountain deposit to the Ingerbelle mill. With the decision to restart mining of the Copper Mountain deposit, the decision was made to design and build a 35,000 tpd grinding and flotation mill near the mining operations. This paper discusses the application of historical operating data for the selection of the mills for the new grinding circuit and provides an overview of the grinding circuit design.

Jan 1, 2012

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By Adrianus (Adrian) Halim, Tomas Bolsöy, Stina Klemo

"This paper describes the ventilation system used in underground hard rock mines in Sweden and Finland, which is very different than the system used in other major mining countries such as Australia, Canada, South Africa, and USA. The system utilizes auxiliary fans with Variable Speed Drive to distribute primary airflow to working levels instead of regulators that are commonly used in other countries. Descriptions about Ventilation on Demand in this system and ventilation regulations in Sweden and Finland are presented in this paper. This paper also quantifies a comparison between the Nordic and the system used in other countries. KEYWORDS Auxiliary fan, Regulation, Ventilation on demand (VOD), Variable speed drive (VSD) INTRODUCTION The primary objective of an underground mine ventilation system is to provide sufficient airflow to dilute atmospheric contaminants that are produced by mining activities. Typically, a mine ventilation system consists of one to four primary fans, regulators to control primary airflow distribution to levels or panels, and auxiliary fans that distribute airflow to dead-end workings via ducts. Depending on circuit geometry, underground booster fans are sometimes used. This system is widely employed in many countries such as Australia, Canada, USA, United Kingdom, and South Africa. However, mines in Nordic countries such as in Sweden and Finland employ a different system, in which auxiliary fans instead of regulators are used to control primary airflow distribution, as well as distributing airflow to dead-end workings. This paper describes the general layout of Nordic ventilation system, its VOD and heating system, its comparison with the system that is widely used in other countries which is referred as “Non-Nordic ventilation system” in this paper, and the current ventilation regulations in Sweden and Finland. The comparison was quantified by doing simulations using Ventsim Design 5 software. DESCRIPTION OF NORDIC VENTILATION SYSTEM General System Layout Figure 1 shows a schematic of typical ventilation system used in Swedish and Finnish mines. The schematic was drawn by Franzen, Myran, Larsson, and Rustan from Stiftelsen bergteknik forskning (Swedish Rock Engineering Research Foundation) and the English translation is written next to the Swedish terminologies. The system is generally a push-pull system. None of Swedish and Finnish mines use exhaust system. As shown in Figure 1, the primary airflow is distributed to levels by auxiliary fans that are bolted to a bulkhead located in the access to intake raise/shaft. These intake fans are attached to ventilation ducts that distribute airflow to all working faces. The exhaust auxiliary fans, which are not attached to any ducts and also are bolted to a bulkhead located in the access to exhaust raise/shaft, then flow the exhaust airflow into the exhaust shaft. A small quantity of this exhaust air is directed into the ramp, which acts as another main exhaust airway. The deepest level is also equipped with booster fan(s) that draw air from the intake shaft/raise and direct it into the ramp to provide fresh air in the ramp. There is no free split in this system. Figure 2 shows a schematic of a level ventilation layout in the Nordic system. Figure 3 shows a photo of these auxiliary fans."

Jan 1, 2019

By G. Belzil, F. Robichaud, M. Fullam

ABSTRACT The Goldex mining and milling complex is operated by Agnico-Eagle and is located in the Abitibi greenstone region of northwestern Quebec, Canada. Commercial production started in 2008. Average gold recovery is 93.5% with approximately 68% of gold recovery coming from the gravity circuit. During the first three years of production, three gravity audits were carried out to optimize performance of the gravity circuit. This paper presents results of the audits and the development of a model linking gravity and overall gold recovery, and outlines improvements made to increase gravity performance and reduce operating costs.

Jan 1, 2013

By R. Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as an inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1995; Walsh and Rao, 1986; Walsh and Kelly, 1992). In November, 1993, the author inspected the grinding circuit at La Mine Doyon in Rouyn-Noranda, Quebec and made recommendations to recover coarse gold and to eliminate gold traps from the circuit. In 1995, the author salted mineral processing circuits with radioactive gold particles. The gamma and X-ray radiation from gold’s nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment using scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps and improving security.Nuclear TracersWhen particles of gold are placed in a nuclear reactor, some of the gold atoms (Au197) absorb another neutron in their nucleus to form gold’s radioactive isotope (Au198). In the process of radioactive decay, this isotope emits high energy gamma rays and X-rays which are easily detected (even through steel) with scintillometers.Radioactive gold (Au198) has a very short halflife of 2.7 days. At the relatively low activity levels used for tracing, the particles remain detectable with a small hand-held scintillometer for about 10 to 14 days. After 14 days the irradiated gold is close to background levels and within two months it is essentially non-radioactive. The radiation has no effect on the recovery characteristics of the gold particles. The gold radiotracers are very safe due to their very low level of radiation, short half-life, and their inherent physical and chemical stability. However, the use and possession of even mildly irradiated gold is strictly licensed and regulated."

Jan 1, 1997

By Andre L. Du Preez

Global mine hoisting regulations require safety fall arrest systems to be installed on vertical conveyance systems capable of safely decelerating and supporting a fully loaded conveyance in the event of a rope severance. Most current arresting systems are incapable of producing controlled safe deceleration rates. Although safety ?dogs? achieve marginally acceptable results on wooden guides, difficulties arise in achieving safe deceleration performance requirement where safety arrest systems operate on steel shaft guides. Previously, arresting systems capable of operating with steel guides have been incapable of producing controlled deceleration rates during the arresting of free-falling conveyances. Most are ?instanton? systems, whereby an occupant inside a conveyance being arrested would be subjected to unacceptably high deceleration forces. This paper briefly highlights the background to the selection process of Rio Tinto?s Technical Staff of a suitable Mine Conveyance Safety Fall Arrest System for #1 Shaft at Rio Tinto Oyu Tolgoi Mine, Mongolia. It also describes the Drop Test and Free Fall Test procedure and the results leading to the acceptance of the Horne Group Levelok® Emergency Braking Technology for the Oyu Tolgoi #1 Shaft in Mongolia. The paper highlights Rio Tinto?s primary objective for the selection of this advanced technology on their primary production shaft cage system as an emergency safety catch braking system combined as an advance hydraulic chairing system. It describes the design and operational parameters and the 'Fail to Safe' interfacing with current automated mine hoist systems.

Aug 1, 2013

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

A pilot scale AG milling campaign was conducted at the AngloAmerican Platinum pilot plant in South Africa. Different blends of hard:soft (silicate:chromite) and coarse:fine particles in the AG mill fresh feed were tested. The effects of multi-component feed on the pilot scale autogenous grinding are presented in this paper, and can be used as a guideline for multi-component feed blends for AG milling. Preliminary modelling and simulation for the multi-component AG mill model are also included.

Jan 1, 2012

By V. I. Lakshmanan, R. Roy

"Zinc is the fourth most widely used metal in the world after iron, aluminum and copper. The primary zinc production is through flotation of zinc concentrate, roasting, leaching and electrowinning. Close to 60% of the metal produced is consumed in galvanizing the steel by making a thin layer of zinc coating on the steel surface by hot dip galvanizing. Process Research ORTECH Inc. has developed an efficient energy-saving sustainable technology for the recovery of zinc from secondary sources such as galvanized steel scrap, dross, dusts etc. The process consists of treating the zinc containing scrap in an alkaline solution to remove the zinc and thereby producing a zinc free steel scrap for recycle. The zinc containing leach liquor is subjected to a solvent extraction process to recover value added zinc oxide as the final product. In this paper, important industrial processes for the recycling of zinc including the PRO process will be discussed. BACKGROUNDZinc is the fourth most widely used metal in the world after iron, aluminum and copper. Global refined zinc output increased by 2.7 per cent to 13.16 million tonnes in 2011 and is expected to increase by an additional 2.4 per cent to 13.48 million tonnes in 2012 [1]. The primary zinc production is through flotation of zinc concentrate, roasting, leaching and electrowinning. Close to 60% of the metal produced is consumed in galvanizing steel by making a thin layer of zinc coating on the steel surface by hot dip galvanizing. Other major usages of zinc are in the production of brass and bronze, die casting and zinc-air batteries. The additional demand for zinc could come from its addition to fertilizers to increase crop yield.While the demand for zinc is increasing, many mines are scheduled to close in near future after being depleted of ore. The mines set to close between now and 2015 are Teck Resources’ Red Dog Mine in Alaska, Minmetals’ Century Mine in Australia and Vedanta Resource’s Skorpion Mine in Namibia [1]. The depletion of resources due to continued use and exploitation is becoming a great concern for the zinc industry. As a result, the sustainability of natural resources for continued societal care has become extremely important. Resource conservation and recovery by recycling with minimal environmental impact is a key element for sustainable development. In this paper, important industrial processes for the recycling of zinc including the PRO process are presented."

Jan 1, 2012