Search Documents

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By Brian Hart, Zhe Chen, Liuyin Xia, Mana Pourdasht, Stamen Dimov

"Gold losses related to carbonaceous matter (CM) during processing are a significant problem in the gold processing industry. Inherent CM in gold ores can behave similarly to activated carbon in its ability to adsorb gold cyanide. This phenomenon is termed preg-robbing as the surface adsorbed gold cannot, for the most part, be recovered. Research has identified that gold adsorption by inherent CM is linked to the specific surface area, pore structure, degree of C disorder and surface functional groups. One of the strategies to inhibit CM preg-robbing prior to leaching is a chemical oxidation; a process linked to modification of the surface functionality. In this study, the variability in gold cyanide adsorption due to oxidation with different reagents has been investigated. Variability in gold cyanide adsorption by CM is examined in relation to structural and surface modifications using TOF-SIMS, XPS and Raman spectroscopy.INTRODUCTION A major obstacle for effective gold recovery during carbon in leach (CIL) or carbon in pulp (CIP) processes carbonaceous gold ores is the presence of carbonaceous matter (c-matter) which has the ability to adsorb, or preg-rob gold from the cyanide leach solution. It can be responsible for poor recoveries as the carbonaceous materials (CMs) within the ore competes with activated carbon used during the leaching and adsorption phase of processing (Cay, 2014). Preg-robbing capacity can vary significantly with mild preg-robbing ores showing absorption capacities of less than 1 g Au/t ore, while severe preg-robbing ores may have CM with the capacity to preg-rob more than 500 g Au/t ore (Dunne, 2007). Research by a number of groups have shown that the degree of C disorder has some influence on the ability of the carbonaceous material to adsorb Au(CN)2- (Miller et al, 2005, Helm et al, 2009, Hart et al, 2010). It is also apparent the adsorption characteristics of carbonaceous material is affected by changes in surface chemistry (Dimov, 2016). Various treatment including; flotation to remove the carbonaceous material (Wills, 2010), addition of surface blinding agents (for example kerosene) to passivate or blanket the carbon surfaces (Dimov, 2016), addition of strong adsorbents (eg. activated carbon or resin) to compete with the carbonaceous material and passivation or surface coating by oxidation (pressure, roasting, chlorination and biological oxidation), have been employed prior to leaching in an attempt to minimize the gold losses (Dunne, 2013)."

Jan 1, 2017

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By G. Stenning

The paper outlines the need for high-volume ventilation in a uranium mining operation based on the design to meet environmental requirements for dust, radiation and diesel equipment. Mining methods in a highly mechanized operation, a key factor in design, are discussed. The construction and installation of major intake and exhaust fans are described briefly, together with the development of the mine airways and distribution system. Controls in the form of doors and bulkheads are important considerations in planning. Finally, the need to lower ventilation requirements in response to increasing power costs will result in future improvements.

Jan 1, 1979

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By S. Caron, M. Bourassa, J. Châteauneuf, L. Tardif

"Since many years, the Yvan-Vézina gold plant custom mills and processes different ore types that show different behaviors. Because of this, cyanidation control is more complex than for a typical milling operation. In 1992, a Cyancor™ on-line « free cyanide » analyzer has been installed for monitoring and optimizing cyanidation. This implementation significantly reduced cyanide consumption for the overall cyanidation process. In order to further reduce cyanide costs, an automatic control strategy has been implemented to decrease fluctuations of« free cyanide » from their set points.This paper outlines the major steps of the project: process control audit, control strategy development, implementation and running-in period. Control strategy features include data filtering modules, adaptive PID algorithm and set points management modules are also presented. Finally, the strategy efficiency is illustrated with load-disturbance responses.IntroductionLocated in northwestern Quebec, the Yvan-Vézina plant has an average capacity of 1300 t/d using carbon-in-pulp technology. In 1991, the Yvan-Vézina gold plant was processing three types of ores (Beauchemin, Mouska and Silidor mines) and a pyrite concentrate (Beliveau mine). A cyanide reduction program was then undertaken to reduce « free cyanide» fluctuations <6>. To reach this objective, the optimum cyanide concentration was determined for each ore, a continuous monitoring method with the Cyancor™ on-line analyzer was developed and a tighter control of cyanide addition was applied. These modifications to the leaching practice significantly reduced cyanide consumption.After a while, it was observed that regulation of « free cyanide » concentrations could still be improved by the use of an automatic control strategy. Yvan-Vézina and CRM began collaborating in 1995 to develop and implement such a strategy. Results show that main disturbances of the circuit (e.g. ore mineralogy and pulp feed rate) can be significantly overcome in order to reduce their effects on the leaching operation."

Jan 1, 1998

By R. Fukuzawa

"The objective of this research is to evaluate the magnitude of carbon prices required to drive process development and innovation for the global nickel industry in a direction that tackles the multifaceted sustainability challenges that the industry faces, including air pollution reduction and greenhouse gas abatement. The results suggest that the currently considered carbon prices are not sufficient to drive innovations in processing methods or upstream pollution prevention. The co-benefits of climate change mitigation and pollution prevention cannot be readily realized under climate change policy alone. Increased coordination between climate change policy and performance-based environmental legislation is necessary. INTRODUCTIONNickel is an important metal in our modern society as it is used in stainless steel, alloys, electroplating and rechargeable batteries, all of which are integral to our economic growth and development (Eckelman, 2010).However, nickel production is energy intensive and therefore susceptible to emerging climate change policies, which may lead to production curtailment and/or increased unit costs of production unless changes in efficiency or energy sources are made (Mudd, 2010). The industry is faced with multi-faceted constraints: future technology must not only deal with metallurgical, financial and environmental constraints but also promote low energy and low carbon practices. This presents a challenge for this industry where technology innovation, development and commercialization are often lengthy, risky and costly processes (Imrie, 2006).Climate change is one of the many challenges faced by our society. Others include other pollution to air, water and land, resources shortage and economic development. From a policy perspective, it is important to balance multiple and often competing needs in an integrated manner. It would require some levels of trade-off in order to maximize the overall effectiveness but also to ensure that one policy does not undermine other policy objectives.The aims of this study are to evaluate how developments in climate change policy would affect the nickel industry in the context of existing environmental regulations and how the industry could respond under these constraints."

Jan 1, 2012

By A. A. Rafiei, J. A. Finch

A previous study comparing n-pentanol and the polyglycol Fl50 showed that the two reagents could give the same gas holdup but with different size bubbles. The finding implies that bubble rise velocity depends on the surfactant (frother) type. A study using bubble swarms supported the frother type effect but bubble interactions were a possible confounding factor. This study resolves the question by measuring the rise velocity of single bubbles of 0.8-2.5mm diameter over a distance :::: 300cm in n-pentanol and F 150. It is shown that at typical frother concentrations used in flotation that the rise velocity in n-pentanol remains comparable to that in water alone while in Fl50 the velocity is significantly reduced. The results confirm the suspected impact of frother type. It is illustrated that in n-pentanol the rise velocity does not reached terminal; while in Fl50 it does and this is the source of the velocity difference. Advances

Jan 1, 2009

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By David Runnels

The Mount Wright iron are mine and upgrading plant were brought on line in the fall of 1975. The mine is located near the Quebec - Labrador border some six hundred miles northeast of Montreal. This paper describes the crushing, grinding and concentrating facilities at Mount Wright, and some design: criteria used in equipment selection and flow sheet design. Also mentioned are some "asbuilt" modifications. A brief description of the over-all flowsheet is also included. Introduction IN SEPTEMBER 1970, the Quebec Cartier Mining Company started development of the Mount Wright iron ore mine. The estimated are reserve is in excess of 1,000,000 ,000 long tons of concentrates, with an average crude are grade of 31.5% Fe. The run-of-mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production r ate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material, of which 50% is waste.

Jan 1, 1977

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

Due to always getting stricter environmental legislations as well as increasing land filling fees the efforts for treating residues from metallurgy are continuously increasing. In case of filter dusts from metallurgical industry, the high zinc bearing electric arc furnace (EAF) dusts or also dusts from secondary copper industry are important sources for the recovery of secondary zinc oxide. Because of low capacities for secondary zinc concentrates (like Waelz oxide) in primary zinc metallurgy, the upgrade of such concentrates to a quality that meets the requirements of high quality (technical) zinc oxide becomes more and more important. This would open the opportunity to break into new markets and use it for example directly in electrolytic galvanizing. Therefore this paper will summarize possibilities for an elimination of halogens from secondary zinc oxides. Furthermore selective volatilization trials, with a synthetic mixture according to the analysis of Waelz oxide, were carried out to remove impurities to achieve an upgraded product quality.

Jan 1, 2011

"An innovative concept is proposed whereby the operating power for haul trucks in certain areas of an underground mine are reduced in order to lower ventilation costs. Airflow that must be provided for diesel-powered equipment in most jurisdictions are regulated based on engine peak power capability and engine emissions, both of which can be lowered by artificially reducing the capacity of the engine through the engine control unit. Advances in asset tracking and ventilation on demand enable this methodology and this study demonstrates that it could represent significant value for mine operators. An examination of haul truck duty cycle indicates that de-rating of engine operating power based on the truck’s location in the mine can enable a step change in ventilation rates, often with no material impact on working conditions. Methods for implementation and estimate of cost savings will be defined.INTRODUCTION Ventilation of underground workings remains a significant operating cost burden for modern mine operators. In particular, ventilation rates for underground diesel mining equipment are often defined by local regulatory bodies and are assumed to present minimal opportunity for optimization or savings, at least until battery propulsion systems can be adopted. Commonly, the quantity of air flow required is defined by the peak rated engine output power of diesel equipment. For example, Ontario Regulation 854 SS 183.1 (3) states that “The flow of air must be at least 0.06 cubic metres per second for each kilowatt of power of the diesel-powered equipment operating in the workplace”. Jurisdictions that define air flow using the prescribed CANMET or MSHA ratings use peak engine emissions to calculate air flow required for dilution ventilation. These approaches are similar in that the maximum power capability of a vehicle’s engine is used to define the ventilation rate in all areas where it travels, regardless of what power output is actually used in any of those areas. Examination of the duty cycle of a typical underground haul truck identifies a large variance in the power output of the vehicle depending on its location in the mine and the activities undertaken at these locations. For example, travel on a mining sub-level requires a fraction of the truck’s peak power due to the minimal grade and significantly reduced travel speed. So if we can reliably reduce the peak engine power capacity and engine emissions in areas where peak power is not required, we can logically cut the ventilation rates for those areas."

Jan 1, 2017

By Vincent Jourdain

Located in the James Bay Territory of Quebec (figure 1), the Clearwater property is jointly owned by SOQUEM Inc. and Eastmain Resources Inc. Exploration on the property since the early 70&apos;s has resulted in the discovery of several gold showings. Exploration work by the joint venture since 1995 has led to the definition of the Eau Claire Zone containing an indicated resource of 540 000 tonnes grading 11.1 g/t Au (8.7 g/t Au cut at 34.28 g/t Au). Hosted by the archean Eastmain Greenstone Belt, the property geology is dominated by mafic volcanics containing thin horizons of felsic volcanics and/or sedimentary rocks (figure 2). The sequence is metamorphosed to the amphibolite facies and contains two small toalitic intrusions. Regionally, the structural trend is oriented E-W but in the area of the Eau Claire Zone a second trend oriented NE-SW is also present. The first exploration work on the property was conducted by SEREM and SDBJ from 1973 to 1976. It consisted of an airborne electromagnetic survey and a ground follow-up program on several grids. This program, comprising geological mapping, geophysics and drilling, led to the discovery of the Natel showing where a drill intersection returned 8.89 g/t Au over 2.65 m. From 1978 to 1985 the area was withdrawn from staking because of the hydroelectric projects of the James Bay. In 1985, Westmin Resources Limited and Eastmain Resources began an exploration program based on a helicopterborne electromagnetic survey. Once again, a ground follow-up program was conducted on several grids. This program included a soil geochemical survey that identified a strong (up to 10 g/t) gold anomaly. Drilling of the anomaly led to the discovery of the Eau Claire Zone where resources were estimated at 270 000 tonnes grading 6.1 g/t Au at the end of 1990. In 1995, SOQUEM Inc. took an option to gain a 50% interest on the property and obtained its interest in 1998. Since 1995, two principal mineralization zones were identified on the property. The "Rosemary Zone" consists of veinlets and disseminations of pyrite and chalcopyrite within a magnetite-rich amphibolite. The mineralized zone was identified by stripping within an area of 1000 by 500 metres. Drilling indicates copper grades up to 0.32 % Cu over 49.2 m. with locally grades of 0.75 % Cu over 5.9 m. The mineralised zone is associated with QFP dykes and corresponds to a strong magnetic anomaly and a strong copper and molybdenum soil anomaly. The "Eau Claire Zone" consists principally of a set of gold bearing quartz-tourmaline veins oriented E-W and dipping at 45-50??to the south (figure 3). More than ten different veins are recognised in the zone and up to eight veins were observed in a single trench (figure 4). The host rock between the veins shows a degree of deformation similar to the regional volcanosedimentary rocks. Each vein is hosted by a unit of actinolite-tourmaline-biotite schist up to one meter thick. The veins and their hosting schist clearly cross-cut the schistosity of the hosting lithologies and the contacts between amphibolites and felsic to intermediate rocks. Usually, the veins are less than a meter thick and are composed of quartz, tourmaline and calcite. The proportion of quartz and tourmaline varies from 0 to 80% within a single vein. The veins commonly show massive, banded or brecciated texture. Sulphides, mainly pyrite, pyrrhotite and chalcopyrite, generally form less than 5% of the vein material.

May 1, 2001

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet &apos;below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By E. C. Roper

THE Britannia Mining & Smelting Company, Limited, have been operating their property at Britannia Beach, B.C., continuously for nearly forty years and have mined over 33,000,000 tons of ore from orebodies within a belt of highly sheared rocks, five miles long by 2,000 feet wide. The property is in the Coast Range mountains, about twenty miles due north of Vancouver. The mountains rise abruptly from sea level to elevations of 4, 500 feet within a horizontal distance of 7,000 feet. The topography has enabled the orebodies to be developed by adit tunnels. The active mining levels are connected to the adits by incline and vertical service shafts. The main service adits are the 2200, 2700, and 4100 levels (see Figure 1). The mine surface shops, three bunk-houses, and over one hundred dwellings form the townsite camp at the portal of the 2200 level adit. A small camp of one bunk-house and a few dwellings is situated at the 2700 level portal. The beach surface shops and camp, adjacent to the 4100 level adit, service the mill, foundry, and other beach installations as well as the mining from the 4100 level. The ore mined from the various orebodies is delivered to the 4100 main haulage level through a system of rock raises and intermediate tramming levels and is hauled on the 4100 level to the mill.

Jan 1, 1945

By lchimura. R. .

Japan Oil, Gas and Metals National Corporation (JOGMEC) and Centro de Investigation Minera y Metalurgica (CIMM) commenced a five year project from 2001 to modify the treatment of the furnace dust from Teniente converter containing harmful elements like arsenic and lead. The project was supported by Japanese and Chilean governments, and a demonstration plant was installed and operated at Las Ventanas Smelter and Refinery (Division Ventanas CODELCO). The basic and detailed engineering was made by Mitsui Mining and Smelting Co., Ltd (MMS) based on the joint study among JOGMEC, CIMM and Division Ventanas CODELCO. Arsenic in flue dust is lixiviated by sulfuric acid and fixed as crystalline ferric arsenate, where leachability of arsenic will be lower enough than the regulation, 5mg/I by TCLP (Toxicity Charactaristic Leaching Procedure) of USEPA. On the other hand, the recovered copper from the dust will be fed to the copper production process at Las Ventanas Smelter and Refinery, while zinc will be recovered as the exportable product. As introducing the crystallization and growing stage, the stable crystalline ferric arsenate formation can be achieved under the normal pressure.

Jan 1, 2007

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017