Search Documents

By T. Grammatikopoulos, A. McKen, O. Christiansen

Vanadium mineralization occurs in oxide-rich horizons within layered metagabbro zones of the Sinarsuk deposit, West Greenland. The main oxide minerals are vanadiferous magnetite and ilmenite, comprising 30% to 90% of the rock volume and the ratio of magnetite to ilmenite ranges from 3:2 to 4:1. Ore microscopy shows that magnetite and ilmenite vary between 0.2 mm and 4.5 mm in grain size, but locally they are coarser grained. Grains are subhedral to euhedral and annealed suggesting that they will liberate very well upon grinding. Electron microprobe analyses indicate that magnetite grains are homogeneous and have a vanadium content, in different mineralized samples, ranging from 1.93 wt% to 2.68 wt% equivalent V2O5. Ilmenite hosts abundant and variably sized hematite lamellae, and it has vanadium contents ranging from 0.32 wt% to 0.59 wt% equivalent V2O5. Preliminary beneficiation of two composite bulk samples shows the samples can be beneficiated fairly easily using low-intensity magnetic separation at a coarse grind (106 microns to 600 microns) to yield a vanadiferous magnetite concentrate. The presence of hematite lamellae in ilmenite prevents recovery of a satisfactory ilmenite concentrate. The most likely beneficiation flowsheet would encompass a primary mill (SAG or rod mill), which would grind to about 600 microns, followed by a rougher magnetic separation stage. The rougher magnetic concentrate would be reground in a ball mill until suitable liberation is achieved. The reground material would then be cleaned in further LIMS stages. However, further laboratory testing is required to establish the final beneficiation program. This work demonstrates the value of mineralogical investigation in guiding and explaining the results of beneficiation processes.

Jan 1, 2002

By Matthew A. Baumann

Tooth-wear on mining shovels requires continuous monitoring. Worn teeth impede excavation performance, increase energy usage, and increase the risk of lost or broken teeth and adapters. A machine-vision-based automated tooth-wear monitoring system is presented. The system employs a rugged boom or stick-mounted camera to capture images of the shovel teeth. An onboard computer processes the images in real-time to determine the length of each tooth. The current wear state is available via a network-accessible log for on-demand status updates. By continuously recording tooth length changes over time, the logs can be used to estimate wear rates and patterns, permitting comparisons between different G.E.T. configurations, operator behaviour patterns, or material types. This detailed, quantitative data permits site-specific optimizations to wear packages and maintenance scheduling. Automating wear monitoring offers the crucial wear information necessary to minimize maintenance costs and reduce unscheduled downtime. A 37-day field trial in a copper-gold mine demonstrated the ability of the system to measure tooth lengths, compute wear rates, and detect differences in tooth wear based on their position on the bucket.

Nov 1, 2011

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

By David H. Searle

This paper will discuss the common trends existing in various Canadian jurisdictions for the closure and reclamation of mines. Included will be a discussion of the requirement to post security as well as its form and how security is calculated and refunded. Reclamation can no longer be left to the end of mine life. Progressive reclamation must occur throughout mine life and must be part of the mine plan from the beginning.

May 1, 2006

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By A. W. Stradling, M. J. Fairweather

"The selective flotation of lead, zinc and iron sulphide minerals is key to the economic performance of concentrators treating zinc-lead ores. Diagnostic metallurgy is a tool to quantify mineral behaviour as a function of particle size and liberation. The result of such analysis may be used to select preferred strategies to improve metallurgical performance. The zinc flotation circuits at three Teck Cominco operations: Sullivan, Polaris and Red Dog are compared here. This paper analyses operating data from each of these circuits. The effects of mineralogy and performance by particle size are emphasized. Metallurgical performance at these three concentrators varies substantially. Liberation size is the major factor in determining metallurgical performance. Complex mineralogy requires a fine grind to achieve effective liberation. Fine grinding results in offsetting decreases in concentrate grade through entrainment. The economic treatment of complex fine-grained deposits requires optimisation of regrind size for liberation without unduly compromising concentrate grade through gangue entrainment.INTRODUCTIONUntil recently Teck Cominco Metals Ltd. operated three mines treating zinc-lead ore. In order of increasing mineralogical complexity they are: the Polaris Mine on Little Cornwallis Island in Nunavut in the eastern Arctic, the Sullivan Mine in southeastern British Columbia and the Red Dog Mine in northwestern Alaska. Both the Polaris and Sullivan Mines have recently ceased to operate due to depletion of ore reserves.The ore type and associated gangue, mineralogy and iron solid solution vary significantly between these deposits. Table 1 summarizes some of the important differences"

Jan 1, 2003

By R. Grant, C. Bazin

"Brunswick Mining has investigated grinding media optimization for the purpose of improving the flotation feed and regrind product size distributions to enhance metal recoveries. This paper presents the findings of on-going testing of various sizes and shapes of grinding media. Plant observations combined with estimated breakage rates demonstrate the importance of appropriate selection of media sizes on the milling operation.IntroductionBrunswick Mining and Smelting is located near Bathurst, New Brunswick, and operates one of the world's largest lead and zinc mines. The ore mineralogy and processing flowsheet have been described elsewhere (Petruk and Schnarr, 1981; Shannon et 01., 1993). Despite the 25 years' milling experience, there has been considerable disagreement as to the required grind size (Grant et 01., 1991). Since 1964, fineness of the flotation feed ranged from 60% to 80% passing 400 mesh (37 um) and averaged slightly above 71% in 1992. Results from mineralogical analysis (Petruk and Schnarr, 1981), laboratory and pilot plant experiments, as well as plant sampling (Grant et al., 1991; Hendriks and Ounpuu, 1985; Shannon et al., 1993) indicate that improved metal recoveries can be achieved by an increase in the fineness of grind, and more specifically by maximizing the amount of material in the 15 urn to 25 um range.This paper shows the results obtained so far from the evaluation of the effect of grinding media size and shape on grinding mill efficiency. The problem of finding optimum grinding media size, shape and composition has been recogrtized since the early 19405. The main criterion for the selection of media size is the size of the material to be ground (Bond, 1958). Although several relationships have been proposed to assist in the selection of grinding media size, none of them are entirely satisfactory (Wills, 1988). Other approaches using the breakage rates and process simulators were developed to help in the selection of grinding media size (Austin et al., 1976; Lo and Herbst, 1986; Concha et 01., 1992; Samskog et al., 1990; Martinovic et al., 1990). Although considerable effort was put into the analysis of grinding media size, very little information is available on the effect of grinding media shape (Norman and Decker, 1985, p. 3C-4). Norris (1952), Kelsall et al. (1973) and Herbst and Lo (1989) have shown that balls are more efficient than other shapes of grinding media including truncated cones and cubes."

Jan 1, 1994

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By Frank Cappuccitti, James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured.The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2005

By Sergio Cattalani, David J. Kerr, Harold L. Gibson

Abstract - The Horne mine was truly a world class Cu and Au deposit. Between 1927 and 1989, it produced some 260 t of Au and 1.13 Mt of Cu from 53.7 Mt of ore that averaged 2.22% Cu, 6.1 g/t Au and 13 g/t Ag. The total value of Au and Cu production from the Horne deposit at metal prices of US$300/oz Au and US$1.00/lb Cu is an outstanding US$5.2 billion. The Horne mine was also a company builder. After optioning the property from Ed Horne (Tremoy Syndicate) in 1922, the Thomson-Chadbourne Syndicate discovered the deposit in 1923 and quickly grew to become Noranda, one of the world’s premier mining companies. This discovery fuelled exploration and, along with subsequent discoveries in the Val d’Or-Cadillac camps, led to the "economic development" of northwestern Quebec. The Horne deposit influenced and continues to influence genetic models for volcanogenic massive sulfide (VMS) deposits. Early observations at Horne contributed to an epigenetic replacement theory for VMS deposits. The most recent genetic model for the Horne, invoking sub-seafloor sulfide replacement of silicified and sericitized volcaniclastic host rocks within a graben, has subsequently been proposed for another giant VMS deposit, the Kidd Creek mine. The Horne and Kidd Creek deposits show many similarities, such as localization within synvolcanic grabens, long-lived hydrothermal activity uninterrupted by volcanism, sub-seafloor replacement sulfides, stacked sulfide lenses, zone refining, silicified footwall rocks characterized by high positive ?18O values, and association with FIII rhyolites. Notable differences between the two deposits include the lack of andesitic, basaltic or komatiitic flows at Horne, different inferred water depths, high Au content at Horne versus negligible Au, but sub-economic to economic concentrations of Sn, In and Cd at Kidd Creek.

Jan 1, 2000

By B. St. Pierre

"The alchemists' symbol for antimony is a diamond with a dot in the centre. The latin name ''stibium'' gives this mineral its chemical symbol ""Sb"" and the name to the principal ore containing antimony. This is Stibnite, a sulphide of antimony, and the valuable mineral at the Consolidated Durham operations. Stibnite chemically pure contains 71.69% antimony metal.Antimony is used in many forms, as an alloy in the production of metal products and as chemical compounds of oxides and sulphides. In Biblical times, antimony was used as a medicine and as eyebrow makeup.Today, the largest single use of the metal is as a hardener and strengthener of lead, and corrosion inhibitor in storage batteries. New applications for antimony in its oxide form as fire retardants are broadening the overall demand especially in the chemical, plastic and fabric industries. Other users include the Military for such things as tracer bullets, shrapnel, smoke screens and flame throwers. An unusual property of the metal is that it contracts when heated which has made it a valuable alloying metal in the printing industry, for heat shields on re-entry vehicles used in the space programmes, and also for the manufacture of bearings."

Jan 1, 1977

By Bob Robinson

In 1990, the European Space Agency (ESA) initiated a technology transfer program to stimulate the wider use of technology developed by the European and Canadian space communities. This paper focuses on the method of technology transfer from the space industry to terrestrial industries, with a focus on the mining resource sector within a program called the Harsh Environments Initiative (HEI) created in 1997. Other resource sector applications include forestry and oil & gas. C-CORE in partnership with the Mining Innovation, Rehabilitation and Applied Research Corporation (MIRARCO) supported by ESA, Canadian Space Agency (CSA) and European R&D organizations conduct projects to promote and demonstrate the transfer of innovative technologies from space to non-space industries. Space programs have and continue to develop new knowledge for extra-terrestrial application, e.g., satellite earth observation, manned missions and unmanned planetary exploration. Many of which hold the potential for application on land and ocean. Currently, space technologies of interest to the mine sector range from robotics and image analysis to sensors, software and advanced materials. The HEI works to identify and apply these types of technologies in the areas of automated/tele-controlled mine operations and mine monitoring.

May 1, 2001

By R. H. Walton

"In recent years the recovery of copper from low grade oxide ores has received widespread attention. The cost of treating such ores using conventional technology, such as milling and flotation, is frequently prohibitively high and copper recovery is generally low. The introduction of heap leaching, solvent extraction (SX) and electrowinning (EW) has resulted in high recoveries, good copper cathode quality and low production costs. This technology has now been successfully applied on a worldwide basis.This paper reviews the various process and design options and gives approximate capital and operating costs for a 1.0% copper ore.INTRODUCTIONAs a result of the low copper prices that prevailed for much of the last two decades, aggressive attempts were made by the industry to cut operating costs. Under such circumstances heap leaching, solvent extraction and electrowinning, to recover low cost copper from oxide ores, has received particular attention and ultimately widespread acceptance.Low grade copper ore (typically containing less than 1.0% Cu), which could not be economically treated by other methods, is placed on heaps and leached with dilute solutions of sulphuric acid. The copper rich, pregnant solution, drains from the heap into a collecting pond and is pumped to a solvent extraction plant where it is purified and upgraded. The resulting solution, termed the pregnant electrolyte, passes to the electrowinning section where the copper is recovered as high grade cathodes and sulphuric acid is regenerated, (Figure 1).This paper specifically describes the processing of copper oxides. Other copper minerals such as chalcocite and chrysocolla are also leached by dilute solutions of sulphuric acid. In practice the oxide minerals are frequently associated to varying degrees with less easily leached sulphides, such as chalcopyrite. In some cases, once the oxidized capping of the ore body is removed, the oxides are totally replaced by more refractory sulphides. Under these circumstances the leaching recovery is significantly reduced. However the principles described here for solvent extraction and electrowinning are also applicable to solutions received from heaps containing sulphide minerals, which are leached more slowly and involve bacterially induced reactions."

Jan 1, 1990

By A. Vien, A. J. Neale, B. C. Flintoff, R. P. Edwards

Froth flotation is one of the most widely used and effective processes for mineral beneficiation. First introduced in 1911, flotation technology has seen many developments over the past 80+ years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results" Klimpel (I 988). While reasonable was sufficient in the past, competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway. This paper examines the role of some of the optimization "tools" in effecting this change.

Jan 1, 1994

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By Christopher F. Gleeson, Roger D. Thomas

"Abstract - Wawa has long been a center of mineral exploration activity and diamonds have been reported in the area since the 1930s. However, diamond exploration did not begin in the area in earnest until 1991. In 1993, Sandor Surmacz and Marcelle Hauseux of Saminex began a prospecting program in the area which culminated in their discovery of the "Sandor" diamond occurrence in an outcrop on the east side of the Trans-Canada Highway. They subsequently optioned the property to Spider Resources Inc. who obtained the necessary exploration permits from Algoma Central Corporation and undertook an exploration program. The diamonds at the "Sandor" diamond occurrence are hosted in the matrix of a spessartite dike composed of actinolite, biotite, and albite. Of the 64 similar dikes that have been sampled and analyzed to date, eight have been found to contain a total of 231 diamonds. Most of the diamonds are of high quality, although they are small.The dikes are non-magnetic and do not have any other geophysical characteristic that can be used to differentiate them from the adjacent country rock. All of the dikes discovered to date have been found by prospecting or by geological mapping by the Ontario Geological Survey. The dikes do not contain pyrope garnet or chrome diopside, two of the commonly used kimberlite indicator minerals. Instead, low Mg, high Cr, Zn-rich chromite, and ilmenites of variable composition, some of which lie within the field of kimberlitic Mg-ilmenite compositions, characterize the diamondiferous dikes. A regional-scale till sampling program for heavy minerals, and geochemical analysis of the <0.177 mm fraction, was used to further define the areas of occurrence of the spessartite dikes and to indicate additional areas for diamond prospecting. Heavy minerals in till that were most useful include: actinolite, chromite, and ilmenite. Geochemical analyses of the dikes show them to contain elevated concentrations of Ni and Cr and to be enriched in Ba, Co, V, Ca, Fe, and Mg relative to the surrounding rocks. Elevated concentrations of Ni and Cr in till occur overlying and down-ice of known lamprophyre dikes."

Jan 1, 2000

By G. M. Hughes, J. Ellis

"IntroductionHydraulics has been considered a science for thousands of years. Applications included water wheels, dam; and slice gates but today the term ""hydraulics"" commonly refers to ""power hydraulics"" in which fluid is used under controlled pressure to do work. The mining industry employee’s hydraulics in practically every aspect of its operations, on such equipment as trucks, front end loaders, LHD units, crushers and hydrostroke feeders. The many benefits of hydraulic drives such as ease of variable speed control, high power: weight ratio low envelope size of hydraulic actuators and ease of maintenance have been extensively developed in the pulp and paper, chemical, steel, and other basic industries, but until quite recently, concentrator operators have not taken advantage of the versatile methods of power transmission offered by hydraulic systems.After some preliminary testing at the Lynn Lake concentrator Sherritt Cordon Mines Limited installed several hydraulic system; at their Fox Mine concentrator to drive slurry pumps and conveyors. The systems used at Fox and the systems which will be installed at the Ruttan concentrator are briefly described in this paper. Since acceptance is based mainly on understanding a few basic principles of hydraulics system; including pumps, motors, circuitry and central methods are also presented in the paper.PRINCIPLES OF POWER HYDRAULICSBasicsHydraulic systems provide an uncomplicated, versatile means of power transmission. The basic system is quite simple. It consists of five main elements, as shown in Figure 1, which are:1. Prime Mover - generally an electric motor.2. Hydraulic Pump - fixed or variable positive displacement type such as a piston or vane p.mp which displaces a constant amount of fluid for ead1 revolution - this unit converts mechanical energy of the prime mover into fluid energy.3. Oil Reservoir - a standard tank to operate under atmospheric pressure which has a capacity of 2 - 3 times the maximum gpm outp.it of the hydraulic pump."

Jan 1, 1972