Search Documents

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By Zhang S

A probabilistic approach is proposed for updating open pit slope sta- bility based on successful performance. The suggested approach is developed within the framework of Bayesian probability theory. In seeking solutions to geomechanics problems consideration must be given to inher- ent variability of shear strength parameters and to the errors in the esti- mation of these parameters. The latter can be significant and may lead to consistent overestimation or underestimation of the values derived from site investigation and testing. Conventional deterministic methods of slope stability analysis do not allow systematic modelling of uncertainties in applied loads or in shear strength parameters. Within a probabilistic framework indicators of stability may be calculated, e.g., the reliability index and the probability of failure. Based on observation of slope per- formance at any given stage of a project, the mean or the standard devi- ation (or both) of a shear strength parameter may be updated. Consequently the indicators of stability can also be updated. The appli- cation of such an approach is demonstrated by an illustrative example.

Jan 1, 1989

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

By N J. Arunakumaren

A coal mine is proposed for an area where a major river traverses the project area. There were initial concerns that inflow of groundwater from exposures of high permeability alluvium associated with the river system could pose mine dewatering problems together with adverse impacts on surface water resources in the river. The project included collation and analysis of geological and hydrogeological data collected historically over a long period of project investigation and evaluation. The project also included establishment of additional groundwater monitoring points to provide a reliable groundwater contours. The groundwater level contours were produced to allow numerical models to be calibrated to support estimation of groundwater inflow. River bed cross sections were also prepared to assist study of the effect of river flow on the inflow. Two separate MODFLOW groundwater models were produced to simulate long-term groundwater inflow to the mine with an upper model consisting of the Quaternary and Tertiary alluvium lumped together and a lower, separate model consisting of Mesozoic coal measures. Analytical solutions were used to predict initial inflow from the alluvium and from the coal measures.

Jan 1, 2003

By A G. Thompson, E Villaescusa, D Howard

The Western Australian School of Mines (WASM) has developed a facility for the static testing of full-scale ground support elements (Morton et al, 2007). The test facility consists of several stiff steel frames used to support the sample and a screw feed jack is used to load the sample. A large-scale punch test method has been developed to load various shotcrete configurations. The shotcrete is sprayed on to a rock substrate containing a centrally located circular disc. The rock and shotcrete sample is placed on to the sample frame and restrained on all sides. The circular disc is displaced at a constant rate by the screw feed jack which in turn loads the sample. Instrumentation measures the displacement and the load being applied to the sample through the loading disc. The testing method is described in detail and the results from the testing program are presented. The results show that it is possible through laboratory testing to simulate some of the mechanisms of shotcrete support reactions better than conventional beam and panel tests.

Jan 1, 2008

By Kyle J. H, Misra V. N

The recovery of copper from a flotation concentrate using ferric chloride leaching has been investigated. The concentrate from the Horseshoe Lights Mine near Meekatharra, Western Australia, contained mainly digenite, pyrite and talc minerals. Over 95 per cent of the copper was dissolved in an acidified ferric chloride solution in one hour at 70¦C and ambient pressure. The pyrite and gangue minerals did not react. The leaching process was found to consist of four separate reactions and the shrinking core model was used to describe the process. The effects of particle size, temperature, concentration of FeCls, stirring speed and leaching time on metal dissolution were investigated. The apparent activation energies in the second, third and fourth reactions of leaching of copper concentrate were 28.8, 11.9 and 53.9 kJ/mol, respectively. The optimum conditions for the leaching of copper from the concentrate, within the range of conditions studied were: particle size 63 per cent minus 38 ¦m, a ferric chloride concentration of 1.48 M, a temperature of 70¦C, and a stirring speed of 800 rpm.

Jan 1, 1991

By Johnston R. F

The factors which influence the reduction of chromite are investigated with special reference to Coobina chromite. This was compared with a South African chromite ore. The reduction characteristics are outlined and the reduction kinetics studied Temperature has the most significant effect, followed by particle size, silica addition and type of coal.Electron microprobe analysis of the products indicates that iron in the chromite is first reduced at temperatures above 1100°C, followed by chromium at around 1200°C. At temperatures greater than 1200°C metallic iron and chromium are formed simultaneously and subsequently give an iron-chromium-carbon alloy. It was observed that the metallic carbide contains a small amount of silicon. The decomposition of the chromite spinel was observed to pass through the FeO.Cr2O3, MgO.Cr2O3 and MgO.AI2O3 forms before slag formation. It is concluded that Coobina chromite is suitable for the production of ferrochrome if direct prereduction followed by intensive bath smelting is used.

Jan 1, 1994

By Kurihara K, Tanimoto C

Construction and mining sites are often subject to unexpected flooding and extensive delays may occur in locating and installing emergency pumps. This particularly applies to sites located in remote areas. A simple and effective pump, called an air-lift pump, can be built from the equipment available at the working site. The basic req- uirements are a compressed air supply, air hose and conventional water pipes. The air-lift pump is comparatively in- efficient but approximately 35 per cent of the available compressed air power at the site can be applied to pumping. Suprisingly high liquid discharge rates may be obtained in suitable applications. The theoretical and practical consider- ations of the air-lift pump are evaluated and a suggested procedure for the emergency design and construction is outlined. INTRODUCTION. Sudden inundations of water into mine and development excavations require the immediate removal of the water if extensive and often irrepairable damage is to be avoided. Pumps installed in shafts or tunnels may become un- servicable due to being totally submerged during the flooding. The emphasis is on rapid

Jan 1, 1976

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By Griffiths J. B

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gippsland Mountains, the Long Tunnel Extended Gold Mining Company produced 13,695 kg of gold, which at 1980 prices represents a value significantly in excess of $200 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subsequent occupants of the lease produced an additional 160 kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tuurriSts. To allow the visitor to obtain a better ;ri.icrstanding of Walhalla's mining past, important parts of the Long Tunnel Extended Gold Mine workings and site are being

Jan 1, 1981

By Veal FL

Technological changes in Portland cement manufacturing during past years have reflected changes in the economics and availability of various types of fuel such as coal, fuel oil and natural gas. The industry consumes a sig- nificant quantity of both thermal and electric- al energy. The nature of the process and its chemical constraints does however permit the use of comparatively low grade fuels such as high ash coal and high sulphur oil. In striving for increased daily kiln outputs and conservation of energy, there is a worldwide trend towards the use of dry process plants. Wet process kilns of about 2 500 tonnes per day assume massive component sizes which present difficulties in manufacture, and transport to plant sites. Large capacity dry process units in excess of 8 000 tonnes per day are now in operation using precalcination techniques in which part of the fuel is introduced in the static preheater section ahead of the kiln while the balance is added to the kiln in a conventional manner. This technique has virtually doubled the potential output of any given single kiln.

Jan 1, 1976

In line with mining operations throughout Australia, Western Mining Corporation Limiter' is striving to increase productivity by intro-ducing mechanized mining techniques wherever possible. Kambalda Nickel Operations' (K.N.O.) largest operating nickel mine, Long Shaft, is currently introducing mechanized cut and fill methods which must provide flexibility to cater for an orebody that variesconsiderably in width, both along the strike and up dip.This has resulted in modifications to the previous approach to primary level develop-ment, and intermediate stope development, and in the type of development and production equipment being employed. Electric-hydraulic diesel jumbos and diesel loaders have now been mated with conventional rail equipment and production airtrack machines are being utilized.The transition to mechanized methods is in its preliminary phase and is being monitored closely to ensure any productivity gains are not offset by a substantial drop in mine grade. The precise method ofmechanized mining has not been finalized and selective methods will be used, according to the ore width and ground conditions, which vary throughout the mine.

Jan 1, 1985

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

By Kajioka H, Nakamura Y

Na2CO3 is a powerful flux for both dephosphorization and desulphurization in oxidizing atmospheres. In order to study refining with Na2CO3 and the nature of the Na2CO3 slag itself, hot metal (4Kg) was melted in Al203 crucibles in a high frequency induction furnace and oxidised with oxygen under Na2CO3 slag. The behaviour of Na2CO3 at high temperature was observed by thermobalance. It was found that dephosphorization ceases in a few minutes and [,P] after refining is easily lowered to less than 0.010%. [%P] after refining is affected by [Si], [P] of hot metal, the refining temperature and the consumption of Na2CO3. Desulphurization also ceases in a few minutes but it shows curious behaviour, increase of [S], decrease of (S) and increase in sulphur lost, during the latter half of run. [%S] after refining is also affected by [P] of hot metal, the refining temperature and the consumption of Na2C03o

Jan 1, 1980

By Jagger N. D

Lead residue from the Zinc Leach Plant at Pasminco's Port Pirie Lead Smelter was previously filtered on a vacuum drum filter and further dried in a gas fired rotary kiln prior to stockpiling and transport to the Sinter Plant. This process involved several materials handling stages, recycled significant amounts of zinc and often resulted in poor environmental conditions. These problems have been overcome by pumping the thickened leach residue approximately 450m to the Sinter Plant where it is filtered in a Larox Automatic Pressure Filter. The filter cake is discharged onto a conveyor belt, held in a storage hopper and then fed directly to the main sinter plant feed stream. Filtrate is returned to the process for additional zinc recovery. The laboratory and pilot plant filtration results are briefly discussed and compared with the operating plant data. The filter installation and ancillaries are described in detail along with the commissioning, operating and maintenance experience over the past 4 years. This installation has overcome the environmental and materials handling problems and resulted in annual savings of approximately $1 million.

Jan 1, 1989

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

By Godresse M, Turczynski G. P J, Driver I. J, Low G, Ozawa N

Geological evaluations of coal deposits have been traditionally undertaken in a somewhat manual manner. Information is collected downhole by chip sampling, coring and using downhole geophysical logging. This information is then interpreted by an experienced geologist to define the coal and noncoal lithological units. Coal units were subsequently correlated to provide data for structural modelling. In recent years a number of advancements in interpretation techniques have been made based on Artificial Intelligence. This paper describes an integrated geological interpretation system based on maximised use of Al techniques. The first part describes the lithological interpretation which uses a number of boreholes with both logged lithology and downhole geophysical logs. This information provides a learning set of data to the neural network. The second part concentrates on the correlation of both coal and noncoal units from borehole to borehole. Problems in this area, in a manual sense, are interpretation of correlation across weathering zones and other geological anomolies. The technique is based on pattern recognition and dynamic programming techniques where a correlation matrix is developed relating all holes with their maximum correlations.

Jan 1, 1995

By Ward S. C, Gardner J. H

In 1990, Alcoa of Australia Limited was elected to the Global 500 Roll of Honour of the United Nations Environment Program for the environmental management and rehabilitation of the bauxite mines in Western Australia. This award placed Alcoa in the international best practice category. The story of constant improvement spans more than 20 years from a 'trial and error' start to a strategically focussed and research driven program today. The main driving force has come from within the company, against a set of strong corporate values and a well publicised Vision based on 'excellence through quality'. Along the way public opinion, action group protests, increased legislative controls together with the professional competence of internal and external environmental resources have all played a part in arriving at the level of current environmental management and mine rehabilitation performance. There were numerous lessons learned here during the evolution and maintenance of best practice. These included: I . To work diligently in obtaining a vision or strategic intent on mine site rehabilitation and environmental management - don't be easily dissuaded.

Jan 1, 1995