Search Documents

By S Hapugoda, A Edenton, M Adam, R J. Holmes, J R. Manuel, R Smyth

Lump ore is one of the key ferrous feeds used in the blast furnace ironmaking process, normally accounting for ten to 20 per cent of the blast furnace burden. Like other feeds, the characteristics of lump ore have an important impact on the stable operation and productivity of the blast furnace. Lump ore is usually assessed chemically, physically and mineralogically to establish its likely blast furnace performance. The physical characteristics of lump ore are strongly related to the chemistry, mineralogy and texture of the ore involved. In this paper, the blast furnace ironmaking process is reviewed, with particular emphasis on the key quality requirements for the ferrous burden material. A variety of key physical characteristics of lump ore measured using standard and non-standard methods are then described and subsequently correlated with the chemical and mineralogical characteristics of the ore wherever possible. Finally, the impact of these physical characteristics on blast furnace operation is assessed.

Jan 1, 2009

By Mukherjee R, Bandopadhyay S

Three applications of fuzzy logic in mineral exploration show the possibility of providing feasible solution and allow greater freedom in decision-making processes for geoexploration data which may be ill- defined, biased or where apriori infor

Jan 1, 1998

By V S. Svinin, V V. Rybin, V A. Maltsev

In large-scale mining, large-sized intermediate pillars, or block-pillars, are generated on the horizon or between closely located mines. These pillars are mined under high rock pressure that results from the stress concentration zones superposition from closely located working excavations. This problem becomes much more complicated if high tectonic stresses occur in the rock mass inducing a rock-burst risk situation. Mining experience gained in mining seven block-pillars at three Khibiny mines in Russia under the geomechanical situation like that described aboveÆ is discussed in detail. It has been shown how safe mine of block-pillars depends on their width, location relative to significant geological failures and uncaved rocks of the hanging wall, the order of pillar recovery, and application of special measures for rock mass stress relieving. Basing on the analysis of the mining experience and special scientific researches, the basic principles are worked-out for safe block-pillar mining under rock-burst prone conditions.

Jan 1, 2000

A career in the mining industry is both challenging and rewarding but comes with some unique complications. Few other industries have such a far reaching effect on individualsÆ lifestyles. Furthermore, few people working within the resource sector could say their job has had no effect on their lifestyle. Mineral deposits in Australia seem to exist predominantly in remote locations like Telfer, Mount Isa and Olympic Dam. With this comes a choice for young professionals; one that is not easy to make, with either alternative often having its pitfalls. This remote nature usually requires professionals (especially graduates and juniors) to choose between a fly-in, fly-out location or relocation to a remote town with less facilities (and some may argue attractions) than their coastal cousins. The challenge for young professionals is to pursue a career that will satisfy their professional goals while developing and maintaining away of life that is emotionally fulfilling.

Jan 1, 2005

Low-grade manganese ore from Sandur, India containing 28.2 per cent manganese and 20.9 per cent iron was roasted with sulphating agents, viz ammonium sulphate and sulphuric acid. The effects of temperature of roasting (300 - 800°C), time (15 - 120 minutes) and amount of sulphating agent (0.5 to 2.5 times stoichiometric amount) were studied. Under optimum conditions, it was possible to extract 92 per cent manganese with 0.5 per cent iron at a temperature of 700°C for 90 minutes duration with stoichiometric ammonium sulphate. Further increase in quantity of ammonium sulphate has marginal effect on manganese extraction.Similar studies were carried out with sulphuric acid, and an extraction of about 87 per cent manganese with similar iron contamination was achieved at a temperature of 700°C for 60 minutes duration with stoichiometric quantity of the reagent. Selective extraction of manganese with respect to iron is discussed.

Jan 1, 1996

By A E. C Peres, J D. Donda

With the aim of producing a concentrate with silica content lower than 1.0 per cent SiO2, laboratory experiments were conducted using a sample of the final concentrate from the Samarco iron ore flotation plant (mechanical cells circuit). The sample contained 3.08 per cent SiO2. This sample was split in two size ranges: >105 ¦m and 2. The >105 ¦m fraction, representing 23.3 per cent of the initial mass, was re-ground to 100 per cent 2 content were obtained. Considering the mass proportions of the two size fractions, the calculated silica content of the combined concentrate was 0.68 per cent, which is considered satisfactory for the objective of this investigation. The major reasons for the higher (0.90 per cent) silica content of the concentrate from the coarse fraction are the presence of silicon in the lattice of goethite and the presence of residual silicious slimes in the pores of porous hematite.

Jan 1, 2005

The Century zinc-lead orebody was discovered in 1990 and contains sufficient reserves to sustain open cut mining at 5 Mtpa of ore for approximately 20 years. It is proposed to pipe mineral concentrate in slurry form 300 km from the mine to the port of Karumba on the Gulf of Carpentaria. The concentrate will be dewatered at Karumba before being transported off-shore to deeper water in a self-unloading shuttle vessel for transfer to export bulk carriers. The four main environmental issues that attracted attention during the impact assessment phase of the project were: the selection of Karumba as the export port, the use of a pipeline to transport concentrate, the risk of concentrate spillage in the marine environment, and aquifer drawdown in the vicinity of the mine. This paper discusses these issues with emphasis on the context of the relationship between the Pasminco Century Project and Gulf communities. Environmental safeguards are discussed, including those that arose out of the negotiations regarding Aboriginal native title.

Jan 1, 1998

By P Wollants, B Blanpain, R Ding

Vacuum oxygen decarburisation (VOD) is the refining process used by ALZ (Genk, Belgium) for their production of stainless steels. The process consists of three stages: oxygen blowing at a pressure of 100 mbar, degassing, and reduction of the slag with ferrosilicon at 5 mbar. The magnesia-chromite bricks used in the slag zone of the ladles suffer from acute wear. In this paper results obtained from a program to improve the refractory life span are presented. The dominant wear phenomena were identified with an electron microscopy study of bricks taken from different locations in the ladle. Concurrently a dynamic model for the vacuum oxygen decarburisation (VOD) refining process was developed. The model calculates the elementsÆ oxidation rate during the blowing oxygen stage and allows the continuous calculation of the change of the metal, slag and gas composition throughout the VOD process. From these activities a general scheme of the refractory wear was worked out and measures to improve the refractory life were proposed and implemented.

Jan 1, 2000

Due to geographical location, AustraliaÆs economy and trading are closely related to Asia. With ChinaÆs increasing demand on resources and energy and Japan and KoreaÆs steady imports in these fields, AustraliaÆs mining industry is experiencing a so called æboomÆ period. Traditionally, engineers or skilled workers from South Africa, Britian or other parts of Europe moved to Australia for its mining industry. Now, more students from Asia are starting to choose mining engineering (similar choices include mining geology, metallurgy, geotechnical engineering and mining surveying) and expect to work in these fields. How does AustraliaÆs mining industry face such a situation? What kinds of challenges and opportunities do the mining industry and universities face? How do mining companies utilise these human resources? This paper concludes with an analysis of all these questions at an industrial level and some personal deduction as to the preferred course for international students.

Jan 1, 2005

By S Servant, T J. Bidwell

Paste backfill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste backfill is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the backfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in situ measurement of paste backfill properties.

Jan 1, 1998

By M D. Kuruppu

Fleet operational effectiveness is fundamental to any operation, becoming highly topical in mines experiencing less than optimal output from their fleets. It is an all encompassing aim to identify those factors that could be improved within production and suggesting solutions in order to optimise the existing fleet and obtain the highest return on capital expenditure. The fleet operational effectiveness of a large open pit truck and shovel operation in Western Australia was examined and a study was undertaken allowing identification of areas falling below target. The annualised hours and production downtimes were investigated to quantify the potential gains of improvements in these areas. The project aimed to maximise direct working hours through determination of the main issues hindering performance. External and internal factors were considered and a continuous improvement program (CIP) was developed. The CIP aimed at internal site-based improvement teams to identify and implement solutions for improvement on a day-to-day basis. Strategies were then identified for the implementation of the proposed changes.

Jan 1, 2003

The importance of orebody definition and optimisation in project development cannot be overstated. Inappropriate orebody definition is the single most important reason for project under performance and/or failure. Without the firm foundation of good orebody definition, the structure of a project cannot be assembled reliably. Many factors need to be considered in the process of orebody definition. These factors are well summed up in paragraph 123 of The Institute's Code and Guidelines for Assessment and Valuation of Mineral Assets and Mineral Securities (Valmin Code). The factors range from the initial geological data through assaying, geotechnical and hydrogeological factors to mining and metallurgical considerations. There are other factors which also need to be considered including marketing and environmental factors. This paper briefly reviews some of these factors and their impact on project development. Three examples are presented where one or more of these factors have had significant impact on the development of the Project.

Jan 1, 1997

By Z B. Rakisheva

By explosion rock mass behaviour is conditioned by preset complex of rocks natural characteristics. Very important role of blockness, which is percent (share) content at examining massif of natural separatenesses of different dimensions and configurations, separated each from other by the cracks of geological and technogene origin. Besides natural properties of massif the power, detonational characteristics of applied explosives, parameters of explosives charges disposition at massif and technology of explosion influence vastly at lumpiness (granulometric structure) of exploded rocks. The mathematical model of rock mass destruction by explosion had been elaborated and substantiated. It ties mutually the initial data (rocks properties, parameters of the charges disposition) and final results of explosion (granulometric structure of exploded rocks). The program of this complicated problem solving had been compiled. Analysing the received results of the problem solving, one can reveal contribution of each group of influence factors for lumpiness of exploded rocks. This fact creates preconditions for elimination or diminution of negative role of some controlled initial data.

Jan 1, 2003

In presenting the paper, Mr. Davey quoted subsequent work which yielded k, at miscibility gap composition, of about 50.We can confirm the authors' findings for k j 300 for nearly pure tin to k 2 about 50 (average 47) from our own experience and from repeat experiments on materials described by the authors, at 1150°C.During laboratory-scale trials we also found confirmation of the authors' view that it is more difficult to reach equilibrium from the high-iron (in slag) side than from the low-iron (high-tin) side. Working from the high-iron side tends to yield results that point to a high k, leading to optimistic values of iron/tin ratio in final slags. In practice the smelting of a tin concentrate, unless it is exceptionally low in tin and high in iron, must yield initially a tin-rich slag and therefore equilibrium can only be reached from the "tinny" side.

Jan 1, 1967

The relative importance of magmatic and metamorphic fluids in Archaean gold mineralisation has long been a subject of debate. Computer simulations can be used to explore the interaction between competing fluid flow drivers, thus providing insight into their role in mineralisation. This approach has been applied to Archaean gold mineralisation in the Yilgarn craton, Western Australia. A simple model representing regional metamorphism in a granite-greenstone terrane indicates that fluid produced during a regional metamorphic event in the Yilgarn was unlikely to have been involved in mineralisation, because it would have escaped from the crust long before the main gold event. Another model illustrates the competition between magmatic fluid production, convection, and deformation. The model shows that the timing of deformation relative to fluid production is important in determining the fate of magmatic and metamorphic fluids, and hence their potential to play a role in mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This brief overview of the history of Brown Coal mining in Victoria is a luncheon presentation -I do not intend to make it indigestible with extensive listings of resources or production. There is a vast pantry of collated historical records and of vari- ous predictive studies available for the enquired with a hearty digestion. A gourmet collation is provided in The Aus IMM Monograph No 11 published in 1984 entitled "Victoria's Brown Coal-A HUGE FORTUNE IN CHANCERY", currently still on offer by the Institute and available at a bargain price in the foyer at this conference. Monograph No 11 also provides a feast of excellent references on the theme of Victorian Brown Coal assembled by the several contributors. In contrast, my presentation paper is a fast-food service, extracts from the printed paper only-you have no choice-you "get what you get" and in small quantity. I hope it will tantalise your appetite -like Oliver Twist you will ask for more. -Buy the Monograph!

Jan 1, 1989

By Towsey C. A

Significant advances in regional geochemical exploration techniques have been made over the last 5 years in the search for gold deposits. This has occurred largely by the development of the bulk cyanide ex- tractable gold (BLEG) also known as the Bulk Cyanide Leach (BCL) tech- nique. The technique has been developed and designed for Australian conditions and has two main ad- vantages over the pan concentrate technique preferred by many ex- plorationalists, viz:,. 1. It is designed to collect ultra fine gold common to epithermal and other north Queensland types of gold deposits. 2. The large sample (approx.5 kg) allows very low detection levels, ranging between 0.1 and 0.05 ppb Au. The use of the BLEG technique in exploration has led to the discovery of the Wirralie gold deposit and numerous other epithermal gold prospects previously undetected by pan concentrate and minus 80 mesh (pathfinder elements) surveys in the Drummond Basin.

Jan 1, 1989

By Yamakita T, Yoneoka Y

The Chigirishima Smelter of Toho,Zinc Co., Ltd. is the largest independent custom lead smelter in Japan and produces about 60,000 tonnes/yr of electrolytic lead. The quantity of slag produced by blast furnace is approximately 65,000 tonnes/yr, 30,000 tonnes/yr of which is sent back to the sintering plant for mixing with lead concentrates. The remaining slag used to be piled up at the yard until the operation of the fuming plant started in July 1977. We examined the slag fuming process with the purpose of achieving: 1) Improvement of the operating results by recovering zinc and lead from blast furnace slag. The lead content in slag at Chigirishima is slightly high, because the height of blast furnace shaft is low and consequently the quantity of sinter smelted per area at tuyere level is rather large. 2) Production of a salable slag as raw material for cement by lowering zinc and lead content in slag.

Jan 1, 1980

In 1975, following a programme of solution characterization and small scale laboratory test work, a pilot plant was constructed to treat waste liquors from the Risdon works. The plant was designed basically to neutralize liquor to a desired pH, and to flocculate, thicken and then filter the resultant pulps. The primary objective was to purify waste liquors to stand- ards set by Tasmanian environmental regulations and at the same time to provide design data for construction of a full scale treatment facility. Waste liquors were divided into two groups, those from the Zinc Plant, and those from the Acid and Superphosphate Plants, and were treated independently. To satisfactorily purify Zinc Plant waste liquors the following reaction sequence was required: 1. Neutralization to pH 10.5 (with aeration for Mn removal). 2. Further reaction of neutralized pulp with Na2S at an addition rate of typically 5 mg of S2-/litre of liquor treated to remove Cd.

Jan 1, 1977

By Lawson F

Pyrite concentrate and calcine from the Nanjing Lead-Zinc-Silver Mines, China, were leached with aqueous cyanide and thiourea solutions. More than half of the contained gold and silver was able to be extracted from the roaster calcines. The very fine dissemination of precious metal grains, high roasting temperature (850 - 900°C) and residual sulphur are believed responsible for the Iow extractions.A recovery of about 70 per cent for both silver and gold was able to be obtained with cyanide and with thiourea leachants when the pyrite was roasted in the laboratory at temperatures between 600 and 650°C.Thiourea, as an alternative leachant, has received much attention recently and a series of constant potential leaching tests was conducted.When the thiourea to formamidine disulphide mole ratio was about two, the precious metal extraction was greatest. In the Nanjing calcined material, this occurred at a potential of about 210 mV relative to a standard calomel electrode.

Jan 1, 1987