Search Documents

This paper presents the water management plan of the Mae Moh Project in the North of Thailand, which includes a large lignite opencast mine and thermal power plants. Lignite production will increase from the present 5.5 million tons per annum to approximately 20 million tons per annum by 1995 when the pit area will be about 20 sq.km. and the depth at over 300 meters. Seven power plants are proposed of which two are under construction. The total capacity to be installed is 2,925 MW. The principles considered for water management are firstly flood protection, including drainage of the mining pit and diversion of the Mae Moh stream away from proposed future mining areas; and secondly, a plan to meet the water requirement of the thermal power plants, while maintaining downstream supplies for irrigation and other purposes. The limited annual run-off of Mae Moh and Mae Chang watershed basins are inadequate for the proposed power plants. A study has been prepared to compare two approaches, namely conveying water from remote watersheds to meet the water requirement of the power plants up to total installed capacity; or by limiting future total generation, at the existing site, to only 2025 MV.

Jan 1, 1988

By Meyer T

Sunburst PCF (Penetrating Cone Fracture) technology has recently undergone extensive underground field trials at Leinster Nickel Operations, Western Australia. Trials with the Sunburst machine started in September 1994 and continued through to December 1994 during which approximately 130 metres of tunnel were developed. The Sunburst technology was used to excavate sub-levels through ultramafic nickel ore for future sub-level caving operations at the Perseverance nickel mine. The Sunburst machine demonstrated reasonable instantaneous advance rates, however, there are still a number of future developments/design changes which need to be addressed prior to the PCF technology being trialed again in a production environment. This paper benchmarks conventional drill and blast at Leinster against the Sunburst Excavator machine performance within similar tunnel dimensions and rock conditions. In addition to productivity and cost information; environmental considerations, support and labour requirements are also discussed. Problems with the current machine design are highlighted and possible future design changes are suggested. The Sunburst machine could be a suitable technology for advancing development through weak to moderate rock conditions and may also reduce overall support costs. With the potential for automation and the ability to reduce rock damage into the development tunnel walls, it is proposed that the Sunburst machine warrants further consideration.

Jan 1, 1995

Recent developments in engine, transmission and control technology, likely to give rise to improved performance and efficiency of underground mobile equipment, are reviewed. Turbocharging and the electronic control of fuel pumps and injectors can improve diesel engine performance whilst minimizing exhaust emissions. Ceramic materials promise further improvements in engine efficiency. Nevertheless, electrically powered machines, equipped with trailing cables or 'travelling plugs' are expected to find increasing application where there is less need for flexibility and where the cost of ventilation and heating or cooling makes diesel engines unattractive. Voltage to frequency converters and induction motors appear to have a future in mains powered machines. Vehicles employing energy storage in the form of batteries or flywheels will find increasing application, but it is expected that they will remain a minority until there is a significant break-through in battery technology. Hydrostatic transmissions having high power density and efficiency are likely to be used more widely. Electronic control systems are likely to be used to simplify jobs and to improve performance and productivity. Enhancement of remote control systems is to be expected for work in unsafe areas, but true robot operation is considered unlikely for the moment. Attention to ergonomic factors should produce significant productivity gains.

Jan 1, 1985

By Misra VN

The carbon-carbon dioxide reaction is the rate determining step in industrial processes such as the rotary kiln direct reduction process for iron ores. The use of brown coal as a reductant in the rotary kiln process has been shown to result in higher throughputs and lower kiln temperatures. No experimental data has been reported on the effect of coal type or the use of brown coal chars. Methods of carbon-carbon dioxide reacti- vity measurement are discussed. None of the methods have been related to direct reduction practice. No standard test has been developed to assess the reactivity of brown coal chars to carbon dioxide. For routine comparative work the gas analysis method of Okstad and Hoy appears to be the most suitable although some modification to the experimental conditions is required. For detailed kinetic studies direct weighing techniques are to be preferred. The factors affecting the reactivity of brown coal char to carbon dioxide are reviewed. Numerous factors such as the origin of the coal, pretreatment and ,physical and chemical differences have been found to affect the reactivity of brown coal chars but no data has been reported on the effect of coal type on reactivity to carbon dioxide.

Jan 1, 1980

By Carroll D. A

The mining and minerals industry has had and will undoubtedly continue to have a considerable impact on the development of this State. For the first 60 years of its history the colony of Western Australia made slow progress; its population in 1889 being only 43,000. However, as a-result of discovering gold at Coolgardie and Kalgoorlie the Eastern Goldfields alone had a population of 25,000 by 1897. The income generated by the gold mining industry allowed the Premier of the day, Sir John Forrest, and his Government to support the proposal put forward by the State's Engineer in Chief, C.Y. O'Connor, to construct a pipeline to carry water from the Darling Ranges to Kalgoorlie ; a distance of 600 kilometres. The demand for people knowledgeable in the science and art of mineral exploitation also prompted the State Government to establish a School of Mines in the Goldfields in 1902, where it has remained ever since. The gold mines of this region have been a major source of employment for over 70 years and there is no doubt of the fact that their continued prosperity minimised the effect of the world recession on Western Australia in the 1930's.

Jan 1, 1979

By Gallet M, Watsford R. M S

The 1989 feasibility study of the chessy, france, copper, zinc, pyrite and barite orebody was based upon a classical flowsheet. The flowsheet included, three stages of crushing, conventional rod and ball mill grinding in series, and sequential flotation of four products utilising conventional mechanical flotation cells. To improve the profitability of the project the partners commenced a search for ways to reduce the projected capital and operating costs of the proposed development. This paper presents the improvements in the projected capital and operating costs as a result of design and concept changes. The major changes included: ò the simplification of the crushing section with the adoption of semi autogenous grinding (SAG) milling of primary crushed ore. ò the deferral of pyrite and barite flotation circuits until market conditions were positive. ò the simplification of the flotation circuit by the use of column flotation cells for combined rougher/cleaner duty. ò the purchase of second hand equipment. The result of these changes was to reduce the capital cost estimate of the plant from US$ 21 million to US$ 11 million and operating cost estimates from US$ 18.90 to US$ 13.60 per tonne of ore for a decrease of approximately ten per cent in potential revenues.

Jan 1, 1991

This paper will describe the exploration project which led to the discovery of the La Escondida porphyry copper deposit in northern Chile and will serve as companion paper to the description of the geology of Escondida being presented by J M Ojeda. The author would like to express his appreciation to Robert Hickman, Chairman of Minera Escondida, for permission to present this paper.In July 1978, a proposal was made by J D Lowell to Robert Wheaton, then Exploration Manager of Utah International, that Utah fund a "grass roots" program exploring for porphyry copper deposits in northern Chile. Wheaton expressed interest, and it was agreed that Getty Oil Co also be invited to participate. A joint venture agreement for the Atacama Exploration Project was signed January 1, 1979, between Utah, Getty and Lowell. The project was managed by Lowell who reported to a management committee which through most of the project consisted of Lowell, Francisco Ortiz, Robert Wheaton, Maurice Young, Sigfried Muessig and Louis Rove. Oliver Warin and Jim Bratt participated in the committee in the last phase of the contract. Special thanks are due Louis Rove of Getty and Maurice Young of Utah who made contributions throughout the course of the project. Francisco Ortiz was resident manager through most of the project.

Jan 1, 1990

By Brien RT, O&apos

The work reported in this paper extends,-bhsb on the "Heat Hardening of Artificial Magnetite ;Pellets"., which was described at the- International Symposium on Agglomeration ;-sponsored by the American Institute. of Mining, Metallurgical and Petroleum Engineers at Philadelphia; U.S.A. in April, 1961. Whereas- that work was of a.,more basic nature, -serving to illustrate the suitability of artificialòmagnetites with various.admixtures, to the application of heat hardened pellets, on: this occasion the aim-is to illustrate the procedures-which were used-to- establish the dimensions of commercialòrecuperativ strands for Australian raw materials,The nature of the pellet feed, i.e. relatively uniform :spheres of4 3/8 in. - 7/16. in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas f lows, and temperatures through beds, the speed and heat requirements of the various stages of heat hardening can be measured, so: that for a specified quality of product estimates can be made of the broad design characteristics of a moving grate system. In practice of course it is .usual to correlate the data from this type-of :experimental 'apparatus with . existing production units upon which good operating data, in the statistical sense, are available.

Jan 1, 1963

Future hard rock mining will gradually move towards complete mechanisation which lends itself to remote control and ultimately to robotic mining. This will require different technical inputs into mining engineering and one of these is in the area of rock'mechanics. Traditional hard rock mining has had little rock mechanics input. Problems arising from high stresses and poor ground conditions have in most cases be remedied after they occurred, in the worst case by abandoning a particular stope or area and starting elsewhere. In a fully mechanised remote or robotic mining situation the financial penalty for such an approach could be severe, as a major part of the production costs will be in the development and the equipment. It is therefore imperative that a complete rock mechanics feasibility study is undertaken before an area is set up for robot mining and that a continuous stability monitoring system is installed that will predict rock behaviour well in advance of mining, such that the necessary ground control measures can be implemented without impeding the continuity of mining. This system will utilise already existing instrumentation such as extensometers and stress cells, and possibly additional improved instrumentation which has to be developed for this particular Application.

Jan 1, 1986

International tenders for contract mining opportunities require the Contractor to make an assessment of risk for an operation with a life span of up to twenty-five years usually based on data made available by the Client. This paper seeks to address how the Contractor assesses the data and quantifies the risks associated with the project. The areas of risk are common to most projects, but in the--Lontractor's case, risk assessment is carried out on the Client's data base and within a compressed time frame of usually less than six months. Incorporation of that risk assessment into the contract documentation is also discussed. Practical examples are given in a number of areas.

Jan 1, 1986

By G D. Cooper

There are no manuals or handbooks for budding mill superintendents or process plant managers. Most who obtain this level of responsibility have gained their training from watching the good and bad of their predecessors and the successful ones have themselves graduated from the school of hard knocks. This paper attempts to provide some helpful guidelines and direction for those who aspire to better manage a mineral processing facility. The authors have 20 years combined experience in senior management roles at nine different mineral processing operations in Australia and overseas, covering gold, base metals and mineral sands. This summary of tips and pitfalls will hopefully benefit future leaders in mineral processing and metallurgy.

Jan 1, 2007

By Gluch KD

The current Mining Act has been the mechanism for administering and encouraging the State's mining industry through the 1970's up to the present. Although it has been subjected to considerable amendment there continues to be judicial challenge as well as criticism in relation to ambiguity of interpretation. Expansion of the mining industry and pressures placed upon "it by the ever increasing interaction with other land users have highlighted deficiencies in the current legislation and the need for a strong and progressive Act covering the rights and obligations of miners and their relationships with those outside the industry. - It is considered that the most positive results can be achieved by a complete redrafting of Queensland's mining administrative legislation.

Jan 1, 1987

The optimisation of human resources provides the path to improving productivity. British Coal has the goal of competitiveness with a quality product in ensured supply. High class skilled professional management teams will analyse job definition and selection procedures for posts, as well as objectives for and delivery of effective management training.Some fundamental changes in attitudes towards training as a means of achievement may be by managers at all levels self-examining their abilities to improve their styles, and by moving training more into the world of high technology techniques. The resulting improvements to management and training with attendant cost benefits will be enjoyed by the companies responding most effectively to these challenges.

Jan 1, 1991

By West R

Since its introduction in 1989, the Australasian Joint Ore Reserves Code (the JORC Code or the Code) has been one of the success stories of the informational interface between the mining industry and investors. This is due variously to the user-friendly nature of the Code itself, to its practical approach to this complex subject, and to the way in which its requirements have been implemented in practice. Recognition of its utility and effectiveness has influenced a significant number of mining countries to re-assess their reporting standards with the positive outcome being that for the first time, a set of standard international definitions for reporting of mineral resources and reserves is a realistic possibility.

Jan 1, 1996

By R A. Bearman

Recent demand pressures for iron ore should not distract from the longer term view that intense competition in the industry has demanded technological innovation of a high order. There is a long track record of successful innovation underpinned by a solid base of scientific research and knowledge. By comment on recent developments in trucks, comminution and direct smelting, this paper suggests that innovation is still a key attribute of the industry. The spending of the minerals industry on underlying science, however, is not particularly high. By looking at other industries we can ascertain that for step change technologies, it is particularly advantageous to have a solid base of science and technology underpinning developments.

Jan 1, 2005

Mount Isa Mines operates Hewlett Packard 1000 computer systems for process control in its major mineral processing plants. To simplify control systems implementation, a process control software package has been developed. This package is now used at the Lead/Zinc Concentrator where the HP computer is interfaced to Foxboro Interspec/Spec 200 system and Honeywell TDC 2000 front-ends. The HP computer controls crushing, grinding, flotation and tailings disposal. This paper outlines the development of process control systems at Mount Isa Mines. The creation of the process control package is described and the reasons for its development highlighted. The application of the software package and the implementation of process control systems at the Lead/Zinc Concentrator is detailed.

Jan 1, 1978

Although the title of this paper permits a very broad scope for discussion, I propose to deal mainly with those aspects of design part- icularly related to rook filling, the'theme of this conference. The unique suitability of belt conveyors for the continuous economical delivery of materials into or out of underground workings, is well established and needs no elaboration. The facility with which conveyor units, comprised of modern modular components, can be adjusted to lengthen or shorten, their ability to be readily repositioned to suit the develop- ment of a work pattern and their virtues as low noise, reliable transport media, are already accepted by all who are involved with the mining industry.

Jan 1, 1973

By J Ralston, R Sedev, D Fornasiero

The foam behaviour of low molecular weight polypropylene glycols (PPG) was investigated as a function of concentration and molecular weight (190 - 2000 g mol-1). For each polypropylene glycol, foam stability increases with concentration and passes through a maximum, beyond which foamability is suppressed as the solubility limit of the glycol is exceeded and droplets of glycol form. Light scattering data as well as static and dynamic surface tension results provide the key information leading to these interpretations. A maximum in foamability was observed for the PPG molecules with increasing molecular weight (caused by a change in molecular conformation at the interface). This suppresses the Marangoni effect and leads to a decrease in foam stability.

Jan 1, 2005

By Ellis CG

The N.S.W. Department of Mineral Resources commissioned its first Mobile Gas Laboratory in 1973.Although originally intended for diesel exhaust analysis, it has been progress- ively made more suitable for mine air analysis. Currently there are two upgraded units in operation. These laboratories have been used at the scenes of four mine fires, two mine explosions and three recovery operations. The authors' experience jointly covers all of these incidents. In this paper they recount the role of the Mobile Laboratory in each incident - including the difficulties encountered - and trace the development of these units to their present state. Future improvements are foreshadowed, and some comments offered concerning the likely future role of these vehicles in mine Emergencies.

Jan 1, 1981

Thermo Fisher Scientific is a supplier of samplers, instruments, analysers and consumables to the mining industry under the Thermo Scientific brand. The critical need to provide a representative sample to the analyser has played a pivotal role in product development. Products discussed are the Analysis and Sampling Station (AnStat) for mineral slurries, the Coal Quality Manager (CQM) and the prototype Bore Hole Analyser (BHX) with optional drill chip recovery system. Analytical techniques used in the above products are XRF, PGNAA and LIBS respectively. The company also designs and supplies conventional mechanical sampling equipment and complete sampling systems for bulk material applications (historical Ramsey brand). These products and application of them are presented.

Jan 1, 2008