Search Documents

By A Havenga, F, J Hough, R Grobbelaar

After the closure of mines they naturally start to fill up with water. As a result, hydraulic gradients develop between adjacent mines and different hydraulic water pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The geometry of the collieries in the central Witbank Coalfield make intermine flow possible in several areas. Since the Department of Water Affairs and Forestry declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon has been undertaken. The importance of the quantification lies in the DepartmentÆs goal of sustainable water management, and the possible long-term financial implications these flows could have for individual mines. The challenges of determining intermine flow are numerous, and attention is focused on the identification of areas where these flows can take place. Detailed mining plans on a regional scale are required, and detailed coal-seam floor data are combined to provide targets for possible interaction between these mines. The quantification of these flows is problematic due to the uncertainties regarding geometrical configurations and the variation in site-specific hydraulic characteristics of the coal and overlying lithilogical layers. To this end, use has been made of several analytic solutions and numerical flow modelling. Stage curves (volume versus elevation curves) for the opencast and underground workings have been calculated and first-order estimates for intermine flow or decant from these areas have been determined. The numerical modelling methodology entailed a down-scaling approach, starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines and finally looking in detail at the major areas of interaction. By considering different scenarios within the context of these flows, possible management options for intermine flow can be evaluated in terms of volumes and qualities that might emanate in the post-closure phases. Challenges for the future include obtaining site-specific information on the groundwater hydraulics and acceptable ranges for model parameters, and verifying model results over time.

Jan 1, 2003

By Gurgenci H, Slifirski M

The Centre for Mining Technology and Equipment was established in 1991 to develop innovative technologies for the mining and processing industries, to introduce these technologies to the industry, and where appropriate, to co-operate with equipment manufacturers to transform these technologies into equipment products. It is an unincorporated joint venture between the University of Queensland, CSIRO and the Australian Minerals Industries Research Association. Base funding for the CMTE is provided by the Federal Government as a Co-operative Research Centre.

Jan 1, 1993

The development of metallurgical training is briefly reviewed. The reasons for the current trend for Metallurgy Schools to become Schools of Materials Engineering or Materials Science are mentioned as is the role of Departments of Chemical Engineering in the teaching of extraction metallurgy. Some problems on academic staff recruit- ment are highlighted and predictions concerning future difficulties in industry getting adequately trained professional staff are made. The need for a special effort to attract and retain the best undergraduate students is put Forward.

Jan 1, 1987

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995

By L Lorenzen, C Aldrich

In this paper, a neurofuzzy model is proposed for the development of an explanatory model of an industrial gold leach circuit based on historic plant data. A regression tree was used to partition the data in the predictor variable space and the structure of the tree was used as a basis for the derivation of fuzzy rules that could be integrated into a fuzzy expert system useful for operator decision support or process control. The position and shape of the membership functions were optimised with a backpropagation algorithm in a neural network framework. The approach yielded a significantly better explanatory model of the gold losses in the plant than comparable linear models. Although a regression tree could perform somewhat better in accounting for the variance of the dissolved gold losses, the tree was less robust than the fuzzy model.

Jan 1, 2007

By Lightfoot BW, Bultitude-Paull J

The Sirosmelt top submerged lancing system has many applications in the smelting of base metal and complex materials. It has particular advantages for smaller scale smelting and the treatment of recycle materials in smelters where its low capital and operating costs and its operational flexibility are of immediate benefit. The system can be fueled by oil, gas or coal, as well as by mixtures of fuels. For many applications, the use of coal as a fuel has operating cost advantages over oil and gas, but conventional pulverised coal feeding systems entail very large capital expenditure and this militates against the use of coal. The methods available for improving on conventional technology for coal firing of Sirosmelt systems are discussed and operating experience with alternative systems are outlined. The use of coal as a reductant in the Sirosmelt system is also discussed.

Jan 1, 1987

In preparation of this Paper, the emphasis has been laid on the commercial rather than on the technical and scientific aspects of coal evaluation. It is intended to describe and comment on the principal factors which currently determine the selection and procurement of coking coal for the steel industry, and is not based on the results of any original research by the author. Evaluation of different coals for strictly thermal uses, for gas production or other chemical applications has not been attempted, and comparisons of coal with other fuels have been excluded: the paper is concerned only with coals for the production of blast furnace coke. The discussion is strongly related to, and illustrated by, British, and to some extent, other Western European practice, but it is hoped that the general conclusions may have a wider application.

Jan 1, 1975

By Q Qian, M Karakus, J Wang, N Melkoumian, D Goodchild, Q Sui, C Wang

Probabilistic analysis is widely used in slope stability assessment because of its capability to take into account uncertainties associated with geotechnical parameters. There are, however, still many unresolved practical issues to the application of the method. One of these issues is the integration of assessments when multiple sets of fractures are considered for the entire slope. In the present study, this issue is addressed within the framework of Monte Carlo simulation. Probability of failure for pairs of fracture sets are assessed independently and the final assessment of the probability of failure for the entire slope is done using conditional probabilities. Prominent Hill open pit, in particular, the problematic fresh Bulldog shale formation, was used as a case study to test the method proposed. The SWEDGE program of the RocScience software package was used for the analysis.

Sep 26, 2011

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993

The B.H.P Company has been using shortwall mining methods for the past six years in the Southern Field. several aspects this experience shortwall equipm H.P. Company has been using shortwall mining methods for the past Northern Collieries and for several years at Corrimal in the Various papers have described and assessed that work. There are of recent work which supplement prior publications. The summary of to date is a background to discussion of the role of self-advancing ent in support in pillar extraction.

Jan 1, 1974

By S R. Hencher

The development and availability of modern software for cavern design over recent years has provided design engineers with a range of usable design tools. The paper discusses the range of modern software available, presents a design methodology, reviews ground investigation requirements and software available for data processing and management, and discusses requirements and common analytical considerations with reference to typical packages. Caution is given of the tendency for readily available and user friendly software to be used without a full appreciation of the underlying engineering principles.

Jan 1, 1999

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

Factors influencing Cost, systems available for transporting minerals, particularly on land, and methods used for comparing costs are reviewed. A case study presents comparative costs graphically for coal haulage, assumed in Queensland, by 31-6" gauge rail, belt conveyor, 120 ton road train, slurry pipeline, and transmission of electrical energy by transmission line. The effect on comparative results of alternative methods of including initial capital and capital replacement costs is considered and approximate break-even points between systems, bearing in mind the assumptions taken, are discussed.

Jan 1, 1973

By K Guilfoyle, A Robertson

In the mid-1970s, trucking ore from 400 m depth to the surface was perceived to be the practical and economic limit for metalliferous underground mines. Improvements in truck design and decline development resulted in the economic depth of haul exceeding 600 m by the mid-1990s. Today, mine operators and contractors are planning to use trucks for ore haulage from depths in excess of 1000 m. The authors of this paper estimate that there are in excess of 300 diesel-powered trucks operating in mines in Australia, and that by the year 2005 more than five per cent of these trucks will be æroad trainsÆ (ie trucks towing powered trailers or truck-trailer combinations). This paper examines the road train concept, presents cost and performance data and describes the advantages and disadvantages of the road train system as well as proposing the types of applications for use of road trains in Australian metalliferous underground mines. Truck performance is based on payload and average speed (expressed as tonnes x kilometres per engine hour (t km/h)). A road train with a powered trailer has a large payload capacity and two engines to provide a high ratio of power to gross weight. Thus it is possible to exceed 300 t km/h per cycle for an average haulage gradient of 1:9 compared to 250 t km/h for conventional articulated dump trucks (ADTs). It is likely that road trains in excess of 100 t capacity will have application for level ore haulage at large mines in Australia.

Jan 1, 2002

By C J. Corbett

Many underground mining methods rely on blasted rock moving under gravity to report to extraction points. Mining of orebodies dipping between 20 - 45 degrees poses a unique challenge for mining engineers in that a dip angle in this range will not allow the movement of broken ore down the footwall to the mucking horizon utilising gravity. This is more so in cases where the natural angle of repose of the rock is less than the dip of the orebody. Hence, innovative mining systems are necessary to mine this type of orebodies. In Australia, the method of uphole retreat panel stoping is commonly used to extract orebodies in the dip range of 20 - 45 degrees and thickness range of 5 - 15 m. In the Zambian Copperbelt a method called continuous retreat updip stoping is used for orebodies with similar dips and thicknesses. The mechanised form of this mining method has potential for application in the metalliferous mining industry in Australia. In this study a comparison is made between mechanised updip (MUDS) and transverse retreat stoping (TRS) methods. A hypothetical nickel sulphide orebody located in Western Australia is used as case study. The net present value for mechanised updip stoping is seven per cent higher than that of transverse retreat stoping based on the assumptions applied. Initial results of this study indicate that mechanised updip stoping can be adopted for Australian mining conditions. However, lack of significant local experience with the method is often cited as a reason for not adopting it even in situations where it is clearly the best option.

Jan 1, 2003

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By Saint-Smith J. C

The anode, tank house and wire bar plant and operations are described with particular reference to those features of design and methods which are characteristic of this refinery at its inception.Reference is also made to auxiliary equipment, transport and materials handling facilities.The work of commissioning the plant late in 1959 is discussed and comment is made on the organisation of construction and origin of the equipment.LOCATION OF PLANTThe site chosen for the copper refinery is on level ground adjacent to the junction of the Mount Isa and the main north-south railway lines at Stuart near Townsville, Queensland. Blister for refining is received by rail from Mount Isa. Refined products are taken 10 miles by road to Townsville Harbour for shipment to other Australian ports or overseas, or despatched by rail direct from the plant.Adequate room for expansion was provided to cover copper refining and any associated industry. The layout of future extensions was planned and space reserved for them before detailing the original units of the main refinery.The initial plant also provides convenient storage facilities and is laid out to derive the greatest benefit from prevailing northerly breezes during the humid tropical summer.As far as possible, the working areas are located so that the prevailing winds cool them as they traverse the buildings.These factors are of very great importance since this is believed to be the only copper refinery in the tropics operating with all white labour and in any case the Company set out to provide the best possible conditions for its operating personnel.

Jan 1, 1961

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

Interactive data exploration is essential for visualising grade distribution and geological controls on orbodies. Quick and appropriate computer techniques for making daily 'value adding' decisions include routine imaging of numerical data suc

Jan 1, 1998

The current drill-and-blast method of tunnelling is cyclic and, for this reason above all others, has a future application potential which is lower than that of continuous methods. There is scope for progress in several facets of today's drill-and-blast tunnelling. But even if each of its unit operations and the synthesis of these were to be optimised, this conventional method will, in the long term, fail to be a serious competitor for tunnelboring machines (TBMs), roadheaders and the like. If its role in tunnelling is not to decline at an increasing rate, drill-and-blast will need to be transformed into a continuous system. Boring and cutting machines consume considerable energy (and expenditure) in creating rock fragments which are smaller than those required by muck-handling equipment. In this respect, blasting is more efficient. Mechanical methods are also less versatile and flexible and, when planning proceeds on a basis of meagre or inadequate geological data, cannot be costed as accurately. Currently, research gains for TBMs and roadheaders are greater than those for conventional tunnelling. If (as is likely) the disadvantages of mechanical methods continue to be reduced at a greater rate, the swing away from drilling and blasting will gain momentum.

Jan 1, 1987