Search Documents

By S Bluhm, R Funnell

Creative mine-designs are constantly being applied in the deep platinum mining industry in South Africa. Recently, this has resulted in deep hot mine-designs including room and pillar, bord and pillar or stall and pillar layouts and the use of in-stope trackless mechanisation. In these mines, the ventilation systems use refrigerated air and high fan pressures and as a result ventilation leakage can have a huge impact. Leakage is a serious impediment to cost-effective operation and potential leakage in future projects is a major factor in judging project viability. This paper describes certain mine layouts and quantifies the extent of the leakage. Based on typical field data, a range of seals from ævery poorÆ to ævery goodÆ was defined and used to estimate overall leakage. Within these mine networks the ventilation pressure, temperature and density all vary significantly and with the multiplicity of leakage paths it was necessary to make use of the VUMA-network simulation package. For the examples examined, the leakage was found to be up to 85 per cent for æpoorÆ category seals and up to 50 per cent for ægoodÆ category seals. The total air flow (and refrigeration) requirements grow exponentially with strike distance due to the compounding effects of higher pressure and more leakage paths. It is shown that beyond certain depths and strike distances the leakage will become so great that it will be impossible to operate cost-effectively û even with ægoodÆ seals. Indeed, in these examples the projects were not considered viable in their original format because of the high ventilation-cooling costs and the mine-designs were modified to include footwall drive systems û the cost of which was justified by the reduced strategic risk to operating ineffectiveness due to leakage.

Jan 1, 2005

By Jiaxin Zhou

Acid mine drainage is a serious and chronic environmental problem of mining. This paper discusses the factors affecting the rate of acid generation by mine rocks and illustrates the relevance of these factors to the mines of the Northern Territory, Australia. The factors may be divided into two groups: internal factors and external factors. The first group covers characteristics of ores, mine waste rocks, tailings, etc and the second group covers surrounding conditions. The latter is further divided into four sub-groups, viz surrounding temperature and pressure, chemical conditions (ferrous/ferric adsorption ratio, total iron concentration, oxygen concentration and pH), surrounding biological conditions and mechanical conditions. Special attention is given to the surrounding P-T conditions, especially water partial pressure, and its relevance to the Northern Territory mines.

Jan 1, 1994

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

The Banda arc, a U-shaped orogenic belt which separates oceanic crust of the Banda Sea from continental crust underlying the Australian- New Guinea shelf, has been interpreted to mark the convergent boundary between the northward-moving Indian Ocean- Australian plate and the Southeast Asian plate (Hamilton, 1979; von der Borch, 1979; Bowin et al., 1980). East of the island of Sumba (Fig. 1), the oceanic crust of the Indian Ocean has been completely subducted and Australian crust is now thrust under the Banda arc. Controversy has centered over the interpretation of the Timor trough as the surface location of subduction and the significance of the Savu Sea between Timor and Flores as either a forearc basin or the continuation of the Java trench (Karig et al., 1987). Two concentric island ridges, called the inner and outer Banda arcs (Hamilton, 1979), separate Australian continental crust from the oceanic crust of the Banda Sea (von der Borch, 1979) (Fig. 1). The inner arc is a typical volcanic island arc composed of calc-alkalic volcanic rocks of Neogene age, while older (Permian and younger) complexly deformed sedimentary and metamorphic rocks make up the outer arc. Timor is the largest and most extensively studied island of the outer arc and is separated from the inner arc by the Savu Sea. The triangular-shaped Savu Sea appears to be a complex forearc basin divided by a series of buried basement ridges (Karig et al., 1987). The outer, convex side of the Banda arc is followed by a major negative bathymetric feature known ne rho Timor trnnnh

Jan 1, 1987

By B Walker, A Robertson, C Wels, S Fortin

A background characterisation study was carried out in the Sangre de Cristo mountains, New Mexico, to: quantify naturally occurring contaminant loads from mineralised areas; define site-specific background concentrations; and to determine key factors controlling spatial and temporal variations in contaminant concentrations. The study included a comprehensive sampling and testing program (paste pH/EC, ABA, leach extraction tests) of soil/bedrock from mineralised areas (including erosional scars), and a ground water and surface water quality monitoring program in selected mineralised watersheds. Results demonstrate that high concentrations of contaminants occur naturally in ground and surface water draining the mineralised area of the Red River basin. The erosional scars were found to represent the major source of acid rock drainage (ARD) (~66 per cent) in this area due to: high rates of weathering and erosion, which continually exposes sulfide-bearing outcrops; and high rates of run-off as a result of high elevation and lack of vegetation. The scar material is generally very acidic (paste pH ranges from 8.5 to 1.5; average = 3.6) with highly elevated concentrations of sulfate and leachable metals. The composition and concentration of leachable metals vary significantly, not only between scars but also within a given scar. While all streams draining the various scar watersheds are highly acidic, each has a characteristic æfingerprintÆ of sulfate and metal concentrations. Most of the run-off from the scars infiltrates into alluvial debris flow aprons and reaches the Red River via groundwater flow.

Jan 1, 2003

By V A. Maltsev, V I. Panin

The question of prediction and prevention of dynamic events û rock bursts (RB), tectonic rock burst (TRB) and mining-induced earthquakes (MIE), induced by large-scale mining, are discussed. The mine itself and the host geological environment are taken as a natural-technical system (NTS) whose evolution is characterised by alteration of the adaptation-bifurcation (catastrophes) periods. So, to predict TRB-MIE means to predict the limiting NTS states that are determined from the NTS geological monitoring data, and to prevent the said events means to control the processes of rock deformation and failure within the critical zone. The study considers particular examples of how TRB-MIE-events are predicted and prevented in apatite mines, Kola peninsula, Russia.

Jan 1, 2000

Comprehensive occupational health and safety legislation in Australia is comparatively recent. It follows the examples set in U.S.A. and U.K. a decade or more ago. In Western Australia the Occupational Health, Safety and Welfare Act was proclaimed in April 1985. It still has a long way to go before it achieves all its objectives. The mining industry has developed a substantial body of health and safety regulations under the Mines Regulation Act. Considerable practical expertise in such matters already exists, much of it developed from hard won experience. As a result it would prefer not to become engulfed in the new legislation. It would prefer to build upon the cooperatively developed policies and workable practices in the field of occupational health and safety with which it is familiar. Associated Minerals Consolidated Ltd. is a leading mineral sands producer in Western Australia and has continuously developed its occupational health and safety policy and practices. Under the banner of "Resource Control", AMC seeks to provide a safe and healthy working environment at all times. This is being achieved through a strategy of a policy, a defined organisational structure and a detailed programme, which together comprise the "Resource Control System". Some of the activities and achievements of AMC in the field of occupational health and safety are compared with the objectives of contemporary legislation, and details of some of the specialised areas of the Resource Control Programme are discussed. The paper will also highlight and discuss impractical areas of potential legislation.

Jan 1, 1986

By Espinosa-Gomez R, Johnson NW

The Copper Concentrator at Mount Isa Mines Limited treats on average 18 000 tonnes/day of chalcopyrite ore containing typically three per cent copper. The main gangue minerals are iron sulphides (-13 per cent) and non sulphide gangue (-78 per cent). In August, 1991, the comminution flowsheet was changed from a conventional circuit (crusher/rod mill/two stage ball milling) to a modem circuit (fully autogenous grinding/one stage ball milling). The 80 per cent passing size of the flotation feed with the conventional circuit was 125 microns. The Copper Concentrator has two parallel grinding lines, two roughing and scavenging flotation lines, and common cleaning, recleaning and retreatment sections. During the first six weeks of the installation phase, one of the two flotation lines was fed by the conventional grinding circuit and the other by the autogenous grinding circuit. Data from parallel surveys and historical data are used to analyse the rougher/scavenger flotation performance before and after the change. The solid and mineral distributions of the flotation feed, the pulp chemistry and the reagent requirements are compared. The mineral liberation before and after the installation of autogenous grinding is compared on a sized basis using data from the 14 consecutive months before, and the seven months after the change. Liberation was measured using the QEM*SEM(*) instrument. The overall effect of the new grinding circuit on the plant metallurgy is also assessed using the copper recovery values, the dilution of the final concentrate and the distribution of copper losses in the final tailings. (*) Quantitative Evaluation of Materials by Scanning Electron Microscopy

Jan 1, 1993

By M Yahyaei, M S. Powell

Mineral processing plants have become large and complex, generally through progressive expansions. Addition of a pre-crushing stage to conventional Semi-Autogenous-Grinding (SAG) and ball mill - crushing (SABC) circuits has introduced a complex materials handling system coping with +200 mm particles. Application of High Pressure Grinding Rolls (HPGRs) and implementing hybrid comminution circuits (ie, HPGR-SAG mill) requires proactive control of the feed size distribution to each unit. Application of Vertical Tower Mills (VTMs) and other fine grinding equipment to achieve a finer grind size, while maintaining the throughput, requires splitting the feed evenly between parallel units. Many of the conventional comminution circuits (ie, staged crushing and screening followed by staged ball milling) must deal with the transition from open pit ore, which is generally altered and soft, to underground ore, which is intact and hard, requiring existing crushers to produce a finer product to unload the ball mills.This paper presents common process improvement opportunities which have been identified during a number plant process reviews conducted by the authors in Australian and international operations. The operation of comminution circuits to known and accepted standards, which is explained in this paper, could improve the performance of circuits by between 5 and 10 per cent, generally at no capital cost and often at a lower operating cost. The performance improvement can be realised as throughput increase, a finer product size, or reduced operating costs (ie, energy saving, low maintenance, less consumables).Process optimisation opportunities presented in this paper include: enhancing materials handling and storage to avoid segregation; standard operation of screens to reduce misplaced materials; proper feeding arrangement and control of crushers to increase their utilisation; preparing proper feed for SAG mills to reduce grind size; splitting the feed evenly between parallel equipment to improve utilisation, and controlling operation of classification units to improve energy utilisation.CITATION:Yahyaei, M and Powell, M S, 2018. Production improvement opportunities in comminution circuits, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 233–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The Graham Farmer Freeway Project in Perth, Western Australia, is the largest urban infrastructure project ever carried out in the State. At a project cost of over $360 million, it also ranks as one of the largest in Australia and is even large by world class standards. The project provides a much needed east-west freeway bypass around the CBD of Perth, linking the Great Eastern Highway in the east with the Kwinana and Mitchell Freeway system in the west. The Bypass will have 6.5 kilometres of freeway, a major bridge over the Swan River, several pedestrian overpasses and underpasses, dual use paths, interchanges and flyover bridges and a rail tunnel. The whole project is being carried out over a four-year time frame, due to be complete and open to traffic in June 2000. The project has been divided into two stages, with Stage 1 including the 1.63 kilometre long Northbridge Tunnel, the subject of this paper.

Jan 1, 1999

By Y Peng, D Liu, S Vink, B Wang

There have been strong industrial observations that clay minerals have a deleterious effect on mineral flotation grade and recovery. However, rigorous explanation on the role of clay minerals in flotation and effective ways to reduce their negative effects are not available. In this study, the flotation behaviour of low quality and high quality coal samples were examined at the Xstrata Oaky Creek Coal plant, and laboratory in fresh and recycled water with high ionic strength. Anionic and non-ionic dispersants including lignosulfonates and triblock copolymers were also tested with an objective of improving coal flotation in recycled water. It was found that overly stable froth was produced in the flotation of both low quality and high quality coal samples in saline water. Speciation modelling indicated precipitation of hydrophilic components which may adversely affect the flotation. Despite the overly stable froth, saline water produced much higher combustible recovery than fresh water without significantly losing the product quality. Lignosulfonate dispersants displayed a potential to improve the flotation in fresh water, but not in saline water. Significant flotation improvement was achieved with the triblock copolymer examined in both fresh and saline water.CITATION:Liu, D, Wang, B, Peng, Y and Vink, S, 2012. Determining the effect of clay minerals on coal flotation using saline water, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 151-158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Carthew SJ

The early period of South Australia's mining history was dominated by Cornishmen as large numbers of miners and their families migrated to escape closure of the Cornish copper mines. Records show that Carthew families migrated from Kent and Cornwall to South Australia. Those from Redruth, Cornwall, were miners and their family history provides an insight into the condi- tions under which early miners lived and worked. Carthews are one of the oldest surviving mining families in South Australia and their movement pattern has been typical of many other early Cor- nish mining families.

Jan 1, 1987

By Gao K, Wu C, Langley J. M, Waugh B, Farrell K

The dissolution of carbon from carbonaceous materials into molten iron is a key step in various ironmaking operations. For example, in new direct smelting processes, carbon in the form of coal is injected into the molten iron bath, which leads to the dissolution of carbon. In foundry operations, typical recarburizer materials can range from high purity graphite to chars. The dissolution performance of these" materials is critical to the operation and could dictate the efficiency and economics of the process.Dissolution kinetics has been studied by various investigators to explain the influence of melt conditions and carbon type (Sahajwalla et al, 1994; Shigeno, Tokuda, and Ohtani, 1985; Orsten and Oeters; 1988; Ganguly and Reid, 1992; Wright and Taylor, 1993). The influence of melt sulphur content on the dissolution kinetics has been characterised (Sahajwalla et al, 1994), with sulphur retarding the rate of carbon dissolution. The carbon dissolution from different sources is seen to vary significantly even under similar melt conditions. This observation has been explained by investigators on the basis of the varying ash content present in the carbonaceous materials. However, ash content alone cannot account for the variability in dissolution kinetics reported in other studies. One such study is presented below.In a recent study (Sahajwalla et al, 1994), pulverised carbonaceous materials were injected into the molten iron bath and the" dissolution kinetics was established. The dissolution of graphite and glassy carbon, which contain almost 100 per cent carbon, was seen to be significantly different when the molten iron contained sulphur. The influence of melt sulphur content was explained on the basis of different wetting behaviour observed.Importantly, the study showed that even pure carbon sources dissolved at significantly different rates. Hence, their performance could not be explained on the basis of ash content.The key difference between graphite and glassy carbon is in their atomic structure. Graphite is highly ordered whereas glassy carbon has relatively poor ordering in its atomic structure. This study showed that the atomic structure in carbonaceous materials can have a significant effect on their dissolution performance.The focus of the present investigation which stems from the past study described above (Sahajwalla et al, 1994), is to investigate the influence of atomic structure of carbonaceous materials on their dissolution into Fe-C-S melts.The specific objective of this study is to determine the relationship between dissolution kinetics and crystallographic character of carbon sources. In order to accomplish this goal, a range of different materials representing a spectrum of carbon sources have been chosen for the investigation. These materials include brown coal char, two types of Auscarb (A and B), and commercial graphite. Auscarb is prepared by calcining Auscoal at 1000°C. Auscoal is made from chemically cleaned Australian coals (Bowling, Chandler and Waugh, 1990). Part 1 of this paper details the dissolution performance of the materials studied, while Part 11 describes the X-ray diffraction study. The relationship between the atomic structural dimension and dissolution rate constant is discussed in light of the results obtained.

Jan 1, 1996

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006

By D Wiseman, R Dunne

Flash flotation is a process that is included in many new mineral processing plants as part of the grinding circuit. Some of the valuable minerals can often be liberated at coarse sizes and will remain in the recirculating loads of the mill until they are reground small enough to report to the cyclone overflow. In addition, minerals of high density report to the cyclone underflow despite being fine in size. This can lead to overgrinding and makes the recovery of valuable fines by flotation difficult. Flash flotation is used to remove the readily floated coarse particles as early as possible and can therefore prevent overgrinding. It thus has the added potential to improve materials handling of the concentrates in such processes as filtration. The merits of including flash flotation within an integrated comminution-conventional flotation circuit is not easy to determine experimentally. Simple batch flotation tests are unable to provide any measure of the possible or probable improvements that are likely to occur from this circuit configuration. As a consequence expensive pilot plant programs are resorted to, to provide the information that will justify the inclusion of flash flotation into a comminution-flotation circuit. Those who have been involved in such pilot plant programs will know of the difficulty in stabilising the circuit as well as selecting the appropriate operating parameters (eg amount of concentrate to be removed in both the flash flotation and conventional flotation circuits). The interactive nature of this circuit (grinding, classification and flotation) is the root cause of these difficulties. Computer simulation, based on information derived from laboratory batch test work or plant and laboratory data, offers an alternative means by which an initial assessment of the merits of a flash flotation circuit can be determined. It can also provide the basis and focus for pilot plant testwork. Recently MacKinnon, Yan and Dunne (2003) developed a model that allows the performance of a flash flotation to be obtained within a closed circuit grinding operation. This paper provides details of an extension of this model to incorporate the interaction of flash flotation on the downstream conventional flotation circuit and allows æwhat ifÆ scenarios to be explored. Details of the laboratory batch test work methodology and the pertinent data derived from these tests that are used in the models and simulation are provided.

Jan 1, 2005

Paddington processing plant is located approximately 30 km north of Kalgoorlie on the Menzies Highway and is owned by Placer Dome Asia Pacific. First mining was from the Paddington Pit, but in subsequent years the plant has had a history of treating ores from a large number of sources, and has used several different methods to reconcile mining and mill production. Reconciliations are necessary to keep a check on the quality control of mining and grade control processÆs. There is a need to be able to identify and resolve issues that will affect the profitability of the organisation quickly. They are also used to check the quality of the resource/reserve statements, and allow the accurate and timely payment of royalties to stakeholders. During the formation of the Kalgoorlie West operations when Delta Gold Limited and Goldfields Limited merged in 2001, the complexity of reconciliations increased dramatically. The expansion of the scope of reconciliations to include two mills, four underground mines and seven open pits, and ore from one deposit to both mills meant that a revised strategy was essential. A variety of issues have arisen over the years with discrepancies occurring when reconciling both tonnes and grade. There are many ways to approach reconciliations, and in recent times these philosophies have been widely debated on site. A consistent and logical approach that takes into account many different sources of ore, as well as different methods of delivery to the Run of Mine stockpiles is therefore necessary. This would standardise the different approaches taken by the various operations that combined to form Kalgoorlie west. The new method reconciles mill production back to the individual ore sources, and produces reconciled-mined tonnes and grade based on the mill throughput and the change in stockpiles. There will generally be a small discrepancy between the claimed mined tonnes produced (and grades) and the mill production. This needs to be highlighted to the operations concerned if it considered unacceptably large. Paddington mill over the last few years has had up to ten sources of ore each year, and up to 15 different stockpiles being processed during each month from those various pits. This combined with the need for a blended oxide/fresh feed, whilst striving to deliver a consistent (grade and hardness) product to the mill, has meant that reconciliations have been very difficult.

Jan 1, 2003

By T Roache, K Yang, M Quigley, C Young

In late 2004 a large-scale evaluation of a new suite of tools for semi-automated core logging was carried out in the Eastern Goldfields of Western Australia. Known as HyLoggingÖ Systems, these combine rapid hyperspectral mapping of mineralogy and very high resolution digital imaging of cores and chips in their original containers. The resulting data is very information-rich and provides information about host rock, alteration and regolith mineralogy. This, in turn, can be used to test geological models about fluid/rock interactions, ore system architecture, ore feed characterisation and generally improve the objectivity of the normally manual and variable logging process. Results were obtained from the Kanowna Belle and St Ives gold deposits in the Kalgoorlie region, as well as numerous holes from across Western Australia stored in the Kalgoorlie Core Library. At the Kanowna Belle gold deposit critical spatial trends in the proportions of white mica, the chemistry and species of those micas, the presence of selected carbonate species and the absence of chlorite proximal to ore zones have all contributed to improved ore deposit understanding. Significantly many of these trends are not discernible to the naked eye, nor easily quantified, previously, across many thousands of metres of core from separate drill holes. At St Ives, the HyLoggerÖ was able to show that low-Al (phengite) and high-Al (paragonite to muscovite) white micas are spatially associated with D3 foliation zones that are proximal and distal to Au mineralisation, respectively. D3 foliation zones are also associated with the depletion of metamorphic chlorite and amphibole, and their replacement with biotite, relative to unaltered mafic host-rocks. The HyLogged GSWA drill holes yielded mineralogical characterisation of classic deposits, including Kambalda (Ni), Fimiston (Au), Teutonic Bore (Cu, Zn, Ag), Black Swan (Ni) and Hannans (Au), illustrating a wide variety of mineralogical trends due to both host lithologies, previously unrecorded lithological subdivisions, and alteration patterns. During 2005 a unique thermal infrared HyLogger was developed to map the important remaining silicates, such as feldspars, quartz, olivines, pyroxenes and garnets. This was successfully tested on a 9000 m subset of the same cores as the earlier study. Interpretation has focused, in particular, on silicification, albitisation, and the mineralogy of several high-grade, less hydrous deposits.

Jan 1, 2006

The Warraua and Mount Poole Inliers form part of a discontinuous series of basement complexes in the northwestern corner of New South Wales. The Inliers comprise mainly clastic sediments of low metamorphic grade (Wonominta Beds) and minor sills, dykes and intrusives, particularly within the Mount Poole lnJier. The Warratta rnlier has received attention due to the occurrence of auriferous quartz-veins where reef mining activities havetaken place.The deformational history of the Warratta and Mount Poole Inljers is characterised by a continuous subhorizontally WSW-ENE directed compression. Deformation was associated with the development of NNW-trending and steeply west-dipping major faults, which bound or biscct the inliers. Chevron folds and a penetrative axial planar cleavage characterise the deformational architecture and document crustal shorterung of at least 40 per cent. In zones adjacent to the major faults and within pelitic and semi-pelitic uruts, a multiple deformational evolution becomes apparent, comprising two events (D1 and D2). Deformational structures considered significant in this study were the result of D1. Tight, northeast-vergent fold patterns FI' and associated axjal plane cleavage SI' and reverse dip-slip movements at major faults indicate early northeast-directed thrusting during D1. This was followed by dextral strike-slip deformation displayed by tight, recumbent folds, en-echelon fold patterns (F2'), a northeast trending crenulation cleavage (52'), and two sets of second order faults, the latter showing high angular relationship to the major faults. A final stage of the deformational history (D2) is represented by WSW-ENE trending kink folds (F2).Auriferous quartz veins, predominantly occurring within pelitic and semi-pelitic units, were generated syntectorucally during the early deformational event (D1) in the course of commencing development of cleavage (S2'). Vein textures point towards vein formation by repeated hydrauJjc fracturing and fracture healing (crack-seal process), and by simple accretionary vein growth. Folded pelite-dominated horizons, considered as low permeability units, are suggested preferential sites where migrating metamorphic Ouids pooled and were trapped, causing high fluid pressure.Hydraulic fracturing and vein precipitation was controlled by lithology and structural constraints such as cleavage.K-Ar dates of approximately 440 Ma (Benambran Orogeny) marking the peak of metamorphism, and coinciding with the development of cleavage S1', also indicate the time of auriferous quartz-vein formation. A period of deformation of at least 30 Ma is proposed for the development of cleavage S1', as constrained by K-Ar dating and the intrusion of a syntectonic granitoid, the Tibooburra Granodiorite.

Jan 1, 1992

By S Paciornik

The traditional trading of iron ores is based on chemical specifications and particle size distribution. However, recent characterisation studies, that bring additional information like mineralogical composition and microstructural (textural) aspects, have become important. They contribute to determination of the iron ores downstream beneficiation operations and subsequent steelmaking processing, allowing improvements on both new and existing processes. Despite progress in commercial scanning electron microscope/energy dispersive spectrometer (SEM/EDS) automatic instruments in the last decade, these systems are not capable of performing the identification and discrimination of major iron ore minerals (haematite and magnetite) and the consequent description of its microstructure. On the other hand, reflected light microscopy (RLM) can easily distinguish the iron oxides by their reflectancies, but it cannot discriminate quartz and epoxy resin, which present similar colour on images. The present work proposes an innovative method to perform a quantitative mineralogy characterisation of iron ore based on RLM-SEM co-site microscopy. This technique combines images obtained by RLM and SEM through an automatic registration procedure that accurately aligns the two kinds of images of each field. In fact, it creates multi-dimensional images, which are then analysed using image processing and pattern recognition techniques. The case study is an itabiritic iron ore from Quadrilßtero Ferrffero (Brazil) which contains mainly quartz, goethite, magnetite and haematite. The discrimination of phases that are not distinguishable with either RLM (epoxy resin and quartz) or SEM (haematite and magnetite) can be performed through this multimodal approach, allowing the subsequent mineralogical quantification. The mineralogical quantification computed by image analysis was consistent with independently obtained results based on the Rietveld technique.

Jan 1, 2008