Search Documents

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By K T. Mandisodza, T J. Cartledge

The principal objective of Geotechnical Engineers supporting operating mines is to provide safe working conditions and ensure that pit designs are geotechnically optimised to site conditions and pre-defined stability requirements. Pit slope designs are delivered in advance of pit excavations. Making changes to these designs is usually slow to enact and involves a layered sign-off before implementation, leading to unwanted delays in their adoption and subsequently increased production pressures. When unexpected ground conditions are encountered during the mining process, or short-term mining schedule requirements demand it, changes to these designs may not be easily feasible in certain situations. It is when these scenarios arise that Geotechnical Engineers need to be proactive and consider unconventional options to deliver safe operating conditions while satisfying short-term requirements to the mine schedule. Essentially, the geotechnical short-term strategic designs double-pronged approach supports the mine schedule while providing safe conditions and minimising geotechnical risks for people and equipment. Common short-term strategic geotechnical designs include; slope buttressing, over-steepening cut slopes to increase reserve recovery through unplanned or emergency cutbacks, and accepting risk threat and operating under unstable slopes. When implementing strategic design options, the Geotechnical Engineer must consider the broader implications for such designs. They must think of the plan’s long-term effects on the mine schedule and pit wall stability. Initiating aggressive designs to recover additional reserves to satisfy a short-term scheduling demand could result in-pit wall instability or suboptimal pit layout. Before and during the implementation phase, the Geotechnical Engineer must communicate and engage with relevant stakeholders to ensure that the plan is executed accordingly and geotechnical risks are effectively managed. Proactiveness to ground response and implementation of risk management strategies will improve safety performance and optimise mining schedules.

Jun 22, 2022

By Regan R

Appin Colliery mines the Bulli Seam with a gas composition of 98.5% methane and 1.5% carbon dioxide. Relaxation of the strata generally occurs to below the base of the Wongawilli Seam, some 40 m below the Bulli Seam, and approxim- ately 125 m above the Bulli Seam, for longwall face widths of 135 m or more. Previous exper- ience showed that when longwall faces were mined for a distance approximately equal to the face width, the mine ventilation could not provide sufficient dilution due to methane emissions from the underlying measures. Postdraining downholes were drilled to intersect the Wongawilli Seam below the operat- ng longwall. These holes were connected to an underground to surface gas range and various suction levels were applied to improve gas drainage. The resulting gas flow rates and purity from all the downholes were regularly monitored and peak flows in some holes exceeded 160 1/sec. The surface plant drained almost 20 million m3 of gas for the period July 1981 to January 1982 at an average methane purity of approximately 70%. Distinct patterns emerged for different downholes from curves illustrat- ing their variations in flow rate with distance subsequent to passage of the longwall face. The difference between free flow characteristics and those obtained with the application of

Jan 1, 1982

By J F. H Thompson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mineral exploration and mining are challenging businesses. Remote and at times harsh conditions have always made it difficult for exploration, but modern explorers also have to deal with cover, numerous technologies, an explosion of data and critical early community engagement. Mining deals with the reality of moving and breaking thousands of tonnes of rock each day to extract what can be a very minor component of economic value, and, furthermore, society expects that this will be done in a clean and sustainable manner. The exploration and mining challenges appear disparate, but they are intimately related.Although not widely appreciated, both exploration and mining have a long tradition of innovation. Over the last 50 years, major step changes in exploration have resulted from radical advances in our understanding of ore forming processes, new geophysical, geochemical and remote sensing technologies, and new ways to integrate and interrogate data. Over a more extended period, close to 100 years, mining has developed bulk surface and underground methods, selective extraction through flotation and leaching and global positioning system–geographic information system control systems that collectively facilitate mining at a massive scale. And yet, in spite of these successes and the boom that we have enjoyed in the last ten years, the industry is under pressure and the need for innovation and change is paramount.The major drivers for innovation are the need for increased quality in discoveries and mines and the need to interact effectively with communities and jurisdictions such that the benefits of quality mines are recognised and enjoyed widely.We are still making new discoveries around the Pacific Rim and elsewhere, but many argue that the quality – grade and accessibility – of these discoveries is decreasing. The net result is that explorers are delivering resources and reserves for development at lower grades and with higher capital and operating costs than current operations. For mining, the increasing age of many existing operations contributes to increasing costs, which, when combined with decreasing cut-offs and lower grades, also results in declining quality. The combined picture does not look good.Just as the pressure to improve performance and margins in the face of declining inputs increases, we are simultaneously faced with increasing societal demands for improved environmental performance and sustainable practices. This is most apparent at the local, community level, where opposition ultimately leads to delays or even cancellation of new projects. Quality is again the issue – quality of the initial and ongoing engagement and quality of the proposed mine in terms of environmental and economic performance.CITATION:Thompson, J F H, 2015. Exploration and mining – the need for innovation , in Proceedings PACRIM 2015 Congress, pp 45–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By N Gupta, R Trivedi, S Bhandari

Managing blasting operations in four mines surrounded by villages is a challenging task. This study aims to compare the blast-induced flyrock as observed in opencast mines by predicting flyrock distance using a soft computing approach known as an adaptive neuro-fuzzy inference system (ANFIS) and Flyrock Predictor software based on empirical studies. Blast design and geotechnical variables such as linear charge concentration, burden, stemming length, specific charge, unconfined compressive strength and rock quality designation were selected as independent variables, while flyrock distance was used as a dependent variable. Out of 120 blasts, data from 100 blasts was used to train and test the ANFIS model. Flyrock distance for the remaining 20 blasts was used to evaluate the model. Flyrock distance has also been predicted using Flyrock Predictor software based on an empirical approach using the same data sets as those used for ANFIS. Performance indices like root mean square error (RMSE), mean absolute error and coefficient of determination (R2) were evaluated to compare the reliability of ANFIS and Flyrock Predictor quantitatively. ANFIS was found to be a better predictive tool, with 1.75 m RMSE and 0.966 R2 compared to Flyrock Predictor, which returned RMSE and R2 values of 2.48 m and 0.932 respectively.CITATION:Trivedi, R, Singh, T N, Gupta, N and Bhandari, S, 2015. Soft computing approach to predict blast-induced flyrock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 455–462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Olwagen, C Stanton, J Gerber

From December 2013 to February 2014 the Southern Middleback Ranges magnetite concentrator went through a successful optimisation process that included the installation of extra grinding power to treat a wider range of ore types. After the initial improvements, sampling surveys were conducted to identify the mineral deportment through the concentrator. Samples collected during the survey were analysed using X-ray fluorescence, quantitative X-ray diffraction and QEMSCAN™ to cross-validate the analysis. Certain streams were also put through a laboratory-scale Davis Tube Recovery washing process to produce clean concentrates for analysis. The QEMSCAN™ analysis identified various metallurgical characteristics (mineral association, particle sizes, grain sizes, particle densities, etc) and these were evaluated for each separation and comminution stage to both understand the processes involved and identify opportunities for improvement. Key findings from the investigation indicated the importance of understanding the elemental deportment of target elements throughout the various minerals. The standard practice of tracking iron deportment through assay provided misleading results on losses to tail through the plant. The investigation provided insight into both wanted and unwanted minerals and the efficiency of each separation stage. The efficiencies of separation are critical due to their impact on downstream capacity, and the investigation provided insight into where opportunities exist to extract more benefit. The findings of the geometallurgical analysis have been implemented on the concentrator, and improvements in the rejection of non-magnetic minerals have been seen.CITATION:Gerber, J, Stanton, C and Olwagen, D, 2015. Using geometallurgy during process optimisation activities at the Southern Middleback Ranges magnetite concentrator, in Proceedings Iron Ore 2015, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Adsorption Behaviours of Humic Substances onto Iron Ore Particle Surface Humic substances extracted from lignite mainly consist of fulvic acids (FA) and humic acids (HA), which have been successfully used as good composite binders for iron ore pellets in laboratory tests and industrial production. However, there exists a general lack of understanding of the interaction between humic substances and iron ore particles surfaces. In this research, by means of zeta potential measurements, Fourier Transform Infrared (FTIR) spectrum, colorimetric method and Environmental Scanning Electron Micrograph (ESEM) imaging, the adsorption behaviours of FA and HA onto the surfaces of iron ore particles are investigated. The zeta potential results indicate that adsorption of FA on the iron ore particles can be characterised by specific and electrostatic interactions, while adsorption of HA is by electrostatic and chemical adsorption interactions. FTIR spectrum results show that adsorption force of FA on the iron ore particle surfaces is stronger than that of HA. From results of colorimetric method, compared with HA, adsorption amount and adsorption rate of FA is more and faster, respectively. FA molecule presents on the surface of magnetite in the shape of an araneose network structure according to the ESEM images, while HA molecule appears on the surface of magnetite in the form of small flocs or microclusters. Humic substances are effective to iron ore pelletisation. Comparsion of agglomeration results show that the different mechanisms of adsorption result in varied agglomeration behaviours. Theses findings above would be beneficial to the implications of composite binder for agglomeration.  

Sep 13, 2010

By R Marchant, D Willingham

"Predictive maintenance (also known as PHM or equipment ‘health monitoring’) refers to the intelligent monitoring of equipment to avoid future equipment failures. In contrast to conventional preventive maintenance, the maintenance schedule is not determined by a prescribed timeline; instead, it is determined by analytic algorithms, such as machine learning, using data collected from equipment sensors and/or via simulation.Predictive maintenance offers the following benefits for operators and equipment manufacturers:reduction of equipment downtime by identifying issues before failure, thereby enabling convenient scheduling of equipment service and extending equipment lifetimeautomatic determination of the root cause of the failure, enabling appropriate service to be performed without utilising resources to determine a diagnosis avoidance of costs of unnecessary maintenance and unexpected failures improved safety and product quality.Algorithms and data are critical to predictive maintenance success. Sensor data preprocessing is performed using advanced statistical and signal processing techniques. In the case that data isn’t available for the full range of operating modes, operating scenarios can be simulated. Machine learning techniques are then used to estimate equipment health. Once tested, predictive maintenance algorithms may be operationalised in an IT environment such as a server or cloud. Alternatively, algorithms may be implemented in an embedded system directly on the equipment, allowing for faster response times and significantly reducing the amount of data sent over the network.In this paper, we use both historical and simulated data of the plant under various modes of operation including run to failure, and we then leverage machine learning techniques in MATLAB to estimate degradation and remaining useful life. This technique, of combining both simulation models and machine learning, in the areas of predictive maintenance and equipment health monitoring has been adopted by Safran, makers of aircraft jet engines, since 2007. They now have over 160 modules developed (Lacaille and Aurelie, 2015).Citation:Willingham, D and Marchant, R, 2016. Predictive Maintenance Using Simulation and Machine Learning, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A Mcquillan, N Bar

Geotechnical models developed during the open pit mine planning stage are generally three-dimensional (3D) in component to capture the spatial variation in geological, structural, hydrogeological and geomechanical conditions. Yet when geotechnical analysis is completed, often the 3D geological, hydrogeological and structural models are simplified to two-dimensions (2D). This paper demonstrates this simplification, through referenced case studies, can lead to the wrong failure mechanism being analysed and/or a conservative Factor of Safety (FOS), or Strength Reduction Factor (SRF), being calculated, leading to a false sense of stability. There exists a paradigm that the FOS calculated using 2D limit equilibrium (LE), or the Strength Reduction Factor (SRF) calculated using 2D finite element (FE), modelling methods is generally conservative, ie lower, than the true FOS. However, this assumption that 3D FOS, or 3D SRF, is always higher than 2D FOS, or 2D SRF, is not always correct (Chen and Chameau, 1983; Bromhead and Martin, 2004; Herza et al, 2017; Pyke, 2017; Dana et al, 2018).

Nov 29, 2022

By P Chapman, B Moosapoor

The objective of this paper is to present the potential applications of geostatistical analyses in planning CPTu investigations, as well as interpolation of CPTu data. The paper presents a case study of a geostatistical analysis of CPTu data undertaken between 2004 and 2017 for an upstreamraised TSF located in the Goldfields region of Western Australia. An initial model is developed using the 2004, 2009 and 2017 CPTu data. The model is used to predict in situ cone tip resistance (qc) measurements, as the interested primary variable, at the selected locations where 2019 CPTu were undertaken, and the results of the prediction and the actual data are compared.

Jul 1, 2021

By A D. Campbell, G R. Power

The increasing availability of marker data in sublevel caving operations is changing the way draw can be managed to achieve positive recovery outcomes in these mines. This paper describes how marker data has been incorporated into flow simulations to help calibrate full mine ore recovery simulations for the forecasting and optimisation of recovery.Some flow modelling techniques do not use marker data, relying instead on the outcomes of physical and numerical experiments to guide assumptions about an idealised recovery flow shape. Other mines have access to marker trial data, but find it difficult to specifically link this marker trial information to their recovery models. This can make it difficult to create a link between the marker trial information and recovery forecasting and limits the potential value of the marker trials at the mine.In the simulations shown here, the marker rings are fully incorporated into the flow model, and can be tracked in the model. The model is compared against the real underground marker recovery information to give the user an indication of how accurately the flow settings in the model are reflecting the conditions in the experimental marker rings. An example of use of this system at an operational mine is included.CITATION:Power, G R and Campbell, A D, 2016. Modelling of real-time marker data to improve operational recovery in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By T J. Laing, A B. Richards, A J. Moore

Blastholes fired in a pattern with a constant initiation delay create a frequency in the ground vibration similar to that from a percussion instrument, such as a drum, in the air. A constant firing delay generates a prime or forcing frequency into the ground motion. The forcing frequency may then be modified by ground transmission characteristics into subharmonics of the forcing frequency. The moving vibration source between blastholes also creates a frequency shift because of a Doppler effect. Other wave interactions may form beats. The effects are exacerbated by the accurate firing times of electronic detonators. This paper demonstrates how observations of wavetraces and frequency spectral analysis were used to recognise:Doppler effect and frequency ellipsoidssubharmonics (and sub-subharmonics) of the forcing frequencybeat formation that may double or triple peak particle velocity (PPV) levels.Recognition of beats permitted techniques to be used to control ground vibration from coal overburden blasting to limits deemed to cause no further instability in a slip failure. An understanding of the science involved has practical application elsewhere that has been successfully applied to initiation timings to reduce PPV and adverse human and structure response from other blasting operations.CITATION:Moore, A J, Richards, A B and Laing, T J, 2015. Blasting harmonics and controlling peak particle velocity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 527–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By G Harbort, D Zoetbrood

"The Phu Kham copper-gold operation in the Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining ten per cent held by the Laos PDR Government.The original 12 Mt/a copper-gold concentrator at Phu Kham commenced production in April 2008. An incremental improvement program resulted in a number of circuit changes being incorporated by 2011, including conversion of conditioning tanks to flotation cells and the installation of a Jameson Cell cleaner scalper. In 2012 the Phu Kham Upgrade Project was commissioned to increase throughput to 18 Mt/a. In April, 2013 the Phu Kham Increased Recovery Project was commissioned to maximise performance by debottlenecking the plant IsaMill™ regrind and cleaning capacity.With the variable mineralogy of Phu Kham ore, control of the c concentrate regrind circuit is essential in terms of achieving effective liberation to maintain concentrator performance. On a routine basis laboratory regrind signature plot data is compared with daily surveys of the operational IsaMills™. More extensive surveys are also conducted to determine size distribution on a mineralogical basis and the effect of fine regrinding on pulp electrochemistry and flotation performance. This paper provides a review of the operating performance of the Phu Kham IsaMills™ with regard to power draw, feed and product size distribution, feed per cent solids, mineralogy and pulp electrochemistry. Operating performance is compared with the IsaMill™ signature plot test for predicting performance.Citation:Harbort, G, Zoetbrood, D and McNab, B, 2016. Operating Performance of the Phu Kham IsaMill™, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S W. Kingman, D Whit, I S. Lowndes

The use of compressive crushing equipment such as gyratory crushers within minerals processing plants can potentially generate large quantities of dust. Remedies to this problem include the retrofitting of shrouds, enclosures, local exhaust ventilation (LEV) systems and water suppression systems. The single or combined application of these systems must be optimised to ensure they operate efficiently. It is desirable that the future design planning of such facilities include integrated dust suppression and/or removal systems to ensure material delivery rates are maintained and the welfare of the workforce is protected. The characteristic release of dust and the disturbance to the surrounding ventilation airflow is investigated by the construction and solution of computational fluid dynamic (CFD) models validated by data obtained from scale experiments. A 3D computational model was constructed using the FluentTM CFD software to represent the background ventilation regime within an underground crushing installation. The falling ore is represented as a continuum granular fluid falling under gravity from the raised bed of the dump truck. Transient path lines are computed to simulate the updraft airflow generated by the tipping process and indicate the dispersion path of any entrained dust. The relationships between the falling ore material, the displaced air and the shear induced flow are determined by an analysis of the computed volume/mass flow rates predicted across the crusher opening. An analysis of the airflow patterns predicted by the CFD simulation models indicates strong shear flows induced between the tipped material and the surrounding airflow in the vicinity of the crusher during tipping, and a strong influence of the background ventilation regime on the path taken by this shear flow. Scale experimental studies were conducted to characterise the induced shear flow and visualise the potential entrainment and transport of dust. An analysis of these experiments is presented.

Jan 1, 2005

By Wyborn L. A I, Idnurm M, Hinman M. C

Comparison of the Proterozoic Apparent Polar Wander Path (APWP) for Australia with the corresponding geology of northern Australia suggests that a number of discrete interplate tectonic events, manifested on the APWP as bends or inflections, may have controlled sedimentary basin evolution, ore fluid production and the timing of mineralisation. Similar features in the Phanerozoic APWP for the North American plate appear to correlate with major orogenic events, basin deformation, movement and 'entrapment' of hydrocarbons and minerals. Interplate tectonic events cause intraplate deformation which in turn controls the subsidence/uplift and sedimentation histories of the basins. Interplate events are thus responsible for creating, deforming and destroying sedimentary basins and the associated petroleum and mineral systems. The basins of northern Australia show remarkable similarities in the successions of volcanic and sedimentary deposits. Unconforrnities of regional or sometimes only local extent have been mapped between the major sedimentary sequences and it is predicted that interplate tectonic events corresponding to bends or inflections on the APWP directly reflect the processes that have produced these widespread unconformities. These processes are also likely to have controlled the geometry and character of the fluid migration pathways and hence the mineralising events. Palaeomagnetic studies of Proterozoic rocks in sedimentary basins provide a tool for predicting the timing of regional mineralisation events, particularly for low-temperature mineral systems. The techniques, when coupled with systematic regional basin analysis, using petroleum exploration techniques, may identify a number of new mineral 'plays' in northern Australia. Prominent inflections in the APWP occur at approximately 1700, 1670, 1650, 1600, 1540, and 1480 Ma. Each of these may be related to a regional compressional deformation, important mineralising event, or significant change in style and type of sedimentation. Most appear to be associated with magnetic overprints. Some of the inflections between 1400 and 540 Ma may also mark significant events in the evolution of Meso- and Neoproterozoic basins. Further work is required to correlate inflections in the APWP with alteration events in order to understand their regional significance.

Jan 1, 1994

By Wyborn L, Giddings J. W, Plumb K. A

The McArthur, Balma (new name) and Habgood Groups are thick (up to 4.5 km) correlative sequences of shallow water evaporitic carbonates, mudstones and sandstones that are exposed largely within the Batten, and southern and northern Walker Fault Zones (Batten and Walker Troughs) of the McArthur Basin respectively. Recent re-mapping of the Walker Fault Zone has provided data for refined stratigraphic correlations between these groups. Two significant hiatuses are now recognised within the Balma Group (base of Vaughton Siltstone and base of Yarrawirrie Formation) and these may represent tectonically-generated sequence boundaries which may correlate with similar local hiatuses within the McArthur Group such as at the base of the Teena Dolomite and Lynott Formation respectively.

Jan 1, 1994

Employing gravity recovery for coarsely liberated gold and sulfide ores has potential to lead to a signifi cant reduction in the energy required for comminution and ultimately can have a significant impact on gold processing. Most of the recognised metallurgical tools at our disposal currently have been designed around recovery of relatively finely ground minerals. In order to change the paradigm of fine grind for liberation, a new set of tools need to be recognised that are capable of separations in the coarser size fractions. Some of these tools already exist and some need to be developed but the key is the way in which the fl ow sheets are arranged. A very strong understanding is required in the existing tools and their capabilities before these new flow sheets can be optimised. Only when we understand the existing gaps in technology can we start to fill these positions with new candidates. Many ores when crushed liberate their gold bearing minerals at coarser sizes than current practice would suggest (Figure 1). In order to characterise this response in ores it is necessary to utilise some new techniques in the lab such as gravity separation and ore sorting at the sizes greater than 15 mm followed by gravity recovery on fractions from 15 mm down to 150 ¦m. The most difficult range has been the mid-sized fraction from 4.0 mm down to around 150 ¦m. This is the size range in which many ores show economic liberation starting to occur and coincidentally this is the range in which many commonly used metallurgical processes reach their operational limits due to physical constraints. Examples of these processes are flotation, hydrocyclones and whole ore leach in agitated tanks which are currently the mainstays of the processing fraternity. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The specification for tender nominated the requirements for ore hoisting and servicing; this showed that one common duty winder could be selected. Foliowing the design of the shaft layout, the merits of fixed or rope guides were compared and the latter selected.The specification called for the supply and installation of the complete hoisting system. Construction of the winder tower and shaft bottom steel work had to proceed while mine development was in progress using the sinking winder and headframe. Guide ropes, winder ropes, and the sky shaft were installed in the shortest possible time, and as the shaft was not equipped with ladder-ways, a second means of access had to be provided.Very few problems were encountered witll the commissioning of the winder, and in the first 2 years of operation the only significant modification was to the circuitry associated witll the moving access platforms.Hoist rope tension checking and adjustment are simple, and non-destructive testing has shown no deterioration of these ropes. The operation of the balance ropes has been very satisfactory but cleaning presented problems in the early stages. Guide ropes have been trouble free and require minimum attention.Normal wear on the PVC rope groove inserts on the winder drum has been negligible.Since the commissioning on fully automatic ·control, the winder has operated with very few, minor delays.

Jan 1, 1969