Search Documents

By M Thompson, N Vines, Z Hearne, S Lam, G A. Gomes-Sebastiaõ, D van der Spuy

Construction and commissioning of the Nova Copper-Nickel project of Independence Group was completed in late 2016. The plant is in the Fraser Range of Western Australia, about 120km east of Norseman and produces separate Copper and Nickel concentrates. Since the early feasibility phases of the project, the importance of automation and control was recognised and planned for to ensure the plant performance meets the design expectations. The site is well equipped with common as well as advanced instrumentation. It currently boasts the largest number of Blue Cube MQi (mineral quantifier inline) slurry grade analysers on a single plant worldwide. It was also decided that 25 Blue Cube TempoTracks would be installed on the flotation cells. The TempoTracks provide information on froth height and velocity, hence giving continuous, quantitative measurements of the froth that is pulled off each cell, rather than relying on infrequent, subjective visual inspections.The Nova concentrator consists of a differential flotation circuit whereby copper bearing mineral are selectively floated prior to nickel flotation. It is imperative that losses of copper to the nickel circuit, and vice versa, are minimised. The plant metallurgical team and Process IQ collaborated to develop and implement the advanced control strategy for the plant. This paper focusses on the optimisation of the copper concentrate that is pulled off the copper rougher and scavengers. This strategy was made possible by the additional measurements listed above. The control optimisation of the copper rougher and copper rougher scavenger circuit was implemented during August 2017 on the StarCSTM advanced control platform. It continuously optimises the level and air setpoints. The control philosophy incorporates several notable techniques which include: a variable mass pull target that is a function of the quantity and grade of material entering the circuit, integrated compensation to prevent inventory build-up in cells, balancing of the froth velocity over the lip of each cell to adaptive, modular system usage and advanced error handling. CITATION:Gomes-Sebastiaõ, G A, Hearne, Z, Lam, S, van der Spuy, D, Thompson, M and Vines, N, 2018. Nova copper-nickel project optimisation of the copper rougher-scavenger circuit through advanced measurement and control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 77–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By H Fletcher

Iron Ore Holdings Ltd (IOH) is an emerging junior iron ore company that is actively developing projects in the Central and Western Pilbara region of Western Australia. IOH commissioned URS Australia Pty Ltd (URS) in mid-2008 to prepare environmental assessment documents for the Phil’s Creek Project, which was rapidly moving into the development phase. This project comprised a small open cut iron ore mine that was expected to deliver approximately seven million tonnes over a five year mine life.IOH faced several challenges in the environmental assessment process for the Phil’s Creek Project. Although the Phil’s Creek Project attained approval but has now been placed on hold, it is a useful case study to discuss these challenges and how IOH addressed them. Several important lessons were learned through this process that can assist other proponents in addressing environmental challenges in a constructive and proactive manner.One major challenge faced by IOH related to the endangered northern quoll (Dasyurus hallucatus). Another challenge was the unusually high species richness of troglofauna recorded within the project area, with several species initially known only from within the proposed pit footprint.Meeting and overcoming these challenges has provided IOH with an increased understanding of the level of input required for consultation with government departments regarding environmental assessments, and this should stand the company in good stead for developing future tenements. Challenges in regards to the environmental assessment process may be faced during future developments, but IOH’s experiences to date and the lessons learned from the Phil’s Creek Project, will help pave the way for successfully overcoming them.

Jul 11, 2011

An Integrated Geology-Mine-Plant and Eco-Efficiency Simulator for Anglo Platinum's Evaluation and Operational Improvement Initiatives

Sep 13, 2010

By T Roesch, M Neurohr, S Stratton

"Dwindling commodity prices are forcing today’s mining operations to increase output. Sometimes the solution is to upgrade the existing infrastructure; however, in most cases it has to be achieved with the same or reduced workforce and with the same equipment capacity through improved process efficiency and higher uptime.Measure, Manage and Improveis the mantra for this years’ Mill Operators’ Conference and while this in most cases relates to the above process efficiency, Siemens has set its focus on the availability and uptime aspect since unscheduled downtime is one of the biggest threats to any grinding operation. Pinion misalignments, resonance, unbalance and bearing and gear meshing faults in geared trains, as well as long-term changes in the condition of the mechanical components or structures and auxiliary systems in gearless systems are the main reasons for unscheduled downtimes in today’s mill drive trains. Our paper outlines the efforts that have gone into adapting conventional condition monitoring methods in conventional, pinion driven mill drive trains as well as gearless systems to capture the gradual deterioration of wearing parts or structural changes in the drive train not only on fixed speed application but also on variable speed applications with multiple operating points. The paper further explores the use of condition monitoring systems as a tool to assess spare thermal motor capacity to potentially push equipment beyond its nameplate rating, along with the process that was followed to correlate measured frequency spectra and envelopes to ambient and load data to understand the kinematics of the drive train.Citation:Neurohr, M, Stratton, S and Roesch, T, 2016. Advancements in Condition Monitoring on Mill Drive Trains for Proactive Maintenance and Early Fault Detection Purposes, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S J. Hawke, L A. Dominguez

In non-ferrous metal mining operations, it is generally necessary to crush and grind the ore to a very fine particle size to effectively liberate the contained mineral from the host rock. Fragmentation by blasting is the first stage of this comminution process.Numerous studies and independent modelling of the Mine to Mill process have demonstrated the potential for significant downstream productivity improvements from improved blast fragmentation. However, safety and environmental constraints associated with the blasting process usually limit the extent to which blast energy or powder factor can be increased.An effective blasting solution has been identified that enables the safe utilisation of powder factors several times higher than those used conventionally to provide significant improvements in fragmentation. The solution uses a static ‘blanket’ of broken rock overlying the blast to contain this increased blast energy and control rock movement. To produce this broken layer of rock, the subdrill in each blast is significantly increased to preblast (or precondition) the entire stemming region of subsequent blasts on the next mining bench.The solution has been evaluated at a large open cut poly-metallic mine in Mexico. Results from the application of this technique have shown significant improvement in run-of-mine fragmentation, with subsequent downstream productivity improvement indicated.CITATION:Hawke, S J and Dominguez, L A, 2015. A simple technique for using high energy in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By A Weeks, W J. Shaw, A Kuk

Grade control is a process that requires the interaction between many components of the mining operation and successful grade control is only realised through good data, robust systems, and a well-trained, motivated and disciplined workforce.The Mt Magnet Gold Project Pty Ltd (MMGP), a wholly owned subsidiary of Ramelius Resources Limited, started mining at Mt Magnet in February 2012 with high expectations for success. Positive cash flow would fund an aggressive exploration and mine development program in the area to increase mine life. Disappointment followed when after start-up the operation had issues achieving budget grade and realising the predicted grade of the mined ore. In January 2013, things started to improve. During the next six months, gold production steadily increased with successive months achieving record production. What had changed?Improvements started following the realisation that controlling grade was not the sole responsibility of the mining geologist and that everyone on-site has a role to play. This paper examines the factors that delivered success for MMGP.CITATION:Weeks, A, Shaw, W J and Kuk, A, 2014. Who is responsible for grade? – an evaluation of the value chain at Mt Magnet Gold Project, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 477–482 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By R Pax

Feed ore variability, the major disturbance into a mineral processing plant receives considerable attention operationally, and at research and strategic levels to ensure that the throughput of the ore are maintained at all times whilst encouraging a sustainable approach to recovering the valuable minerals from ore bodies. Effort and insights from mineralogical and processing characterisation (eg. ore hardness) of sub-ore body domains allows sequencing for processing to ensure consistency and throughput for the size sensitive grinding unit processes. Optimising the blast fragmentation has benefit as does pre-concentration using ore sorting. Blending of ore domains with different characteristics is common for operations. In recent years a number of technologies have become available for on-line and more rapid assessment of ore and have been discussed in a recent paper by Cameron et.al. (2016) as an opportunity for further utilisation of mine-to-mill (and mine to product) strategies. Current concepts have focused on extensive characterisation of ores so that current control practices can be realised and made more effective with relatively slow measurements and actuation. CITATION: Pax, R, 2018. Dynamic concepts for mine to mill operation and optimisation, in Proceedings Complex Orebodies Conference 2018, pp 124–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Devencorn

The development of robust, economical transport infrastructure has been identified as a key driver to sovereign economic growth. Notwithstanding the value of undeveloped mineral resources, unless they can be brought to market they are of little value. Within a global context, the continent of Africa probably faces one of the most significant transport driven economic development programs as countries strive to unlock their much sought after resources.The UN’s Africa Review Report on Transport (United Nations Economic and Social Council, 2009) provides an excellent context for the issue facing African countries and the potential for investment in transport to solve many of the intrinsic problems they are confronted with. With little exception, economic development in Africa is very likely to be driven ‘off the back’ of transport development – and more specifically from heavy-haul rail as a means by which economic wealth can be derived from export of the continent’s vast natural and mineral resources to the world. The report found:transport is a key driver of economic development and poverty reduction;road transport is the most dominant mode in Africa;the ‘Cost to Market’ of African goods is hampered by the reliance upon road transport;the cost of road transport is not just economic – 19 per cent of the world’s road fatalities were recorded on African roads;African railways are seen to be disjointed and under-utilised;Africa’s ports are key to export trade - yet only six ports (three in Egypt, and three in South Africa) handle about 50 per cent of the continent’s total container traffic;the cost of transport is increasing making African trade even less competitive; andsignificant negative impacts of Africa’s reliance on road transport – health, and greenhouse emissions.We understand that mining the resource is only part of the solution – it has to be put to market at a competitive landed cost.Most African countries face huge costs associated with transport development and ongoing operation – in many cases beyond their available resources.The Australian rail industry has faced and solved many of these challenges.

Nov 22, 2011

By L Vimercati, R Williams

Transitioning to a green future requires the mining industry to adopt sustainable practices. Filtered tailings are become a key expectation of the communities we operate in and are growing in a number or mining commodities including bauxite, nickel, gold and iron ore. The filtration technologies required range from dewatering screens to vacuum and pressure filters. Particular challenges faced in iron ore applications include large scale which means several units of large size are often required. In addition, a high specific gravity that cause sedimentation issues and a high abrasion level make demands on achieving reliability level at above 90 per cent. This paper describes the testing, selection criteria and specific features required to provide a rational option for equipment and plant design. An example of how this has been applied in an iron ore application in Brazil is used to demonstrate a successful outcome. This project installed four overhead beam filter presses each producing around 200 t/hr utilising a recessed chamber plate, feed pressures up to 15 bar, cake thickness of 5 mm. The moisture lower than 20 per cent that was produced was considered to provide material with handling and geotechnical properties to guarantee a safe stacking. Regular high pressure washing at 100 bar was considered imperative to maintain cloth life and process performance. The correct management of the system (OPEX control) by PLC control ensures a balance between machine potentials and plant needs. With this equilibrium it is possible to limit mechanical wear preserving equipment lifetime.

Sep 18, 2023

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

By J Heyes, G A. Maddocks, R J. Stewart, G D. Corder

Mining is an international business and vital contributor to national and global economies. It depends on the trust and confidence of investors and stakeholders for its financial and operational well-being (Committee for Mineral Reserves International Reporting Standards (CRIRSCO), 2016). The Social Licence to Operate (SLTO) is an increasingly multifaceted and multistakeholder risk that can impact investment decisions. Community challenges to broader political and economic decisions have given rise to protest delaying or stopping projects or closing mines and has led to loss of life (Ernst and Young, 2016). Some governments are now giving greater powers to stakeholders to make the final decision on approving mining and metals activities (EY, 2016). With billions of dollars in project investment at stake, ongoing engagement, collaboration and effective communication with stakeholders is crucial and mutually beneficial solutions are increasingly expected (EY, 2016). It is therefore essential that the industry communicates the risks (and opportunities) associated with investment effectively and transparently in order to earn the necessary level of trust with investors and stakeholders to underpin its activities (CRIRSCO, 2016). Despite this need, investor and stakeholder trust in the sector has eroded in recent years.CITATION:Maddocks, G A, Corder, G D, Heyes, J and Stewart, R J, 2016. The social licence to operate and drivers for change – resource reporting and mine material characterisation, in Proceedings Life-of-Mine 2016 Conference, pp 183–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By N Ross, N Goldup

In recent years the heavy mineral mining industry has started to look more closely at the feasibility of mining moderate to high slimes deposits. During the initial stages of orebody evaluation the primary purpose of the pilot plant is to produce heavy mineral concentrate for metallurgical evaluation. Hence, generally little consideration is given to the disposal of the waste material (slimes and tailings). This paper suggests additional, simple, low-cost, tests that can easily be incorporated into an initial pilot plant operation. With this data a more definitive evaluation of available waste disposal options can be made during the early stages of the project. Thus, permitting better project focus and utilisation of resources. These tests include free settling of slimes, natural slimes drying and consolidation (undrained and drained), tailings stacking angles, and particle size distributions of input and waste streams, etc. The objective and method of each test is summarised, together with its relevance to possible waste disposal options. The results of this preliminary testwork can later be used to expand upon and define further tests for the second phase of pilot plant operations, which will enable a more definitive evaluation of a proposed waste disposal solution.

Jan 1, 2001

By K W. Bian, Y M. Liu

Tongkuangyu Copper Mine is currently the only mine in China employing block caving. It comprises two large orebodies known as the No 4 orebody and the No 5 orebody. They are approximately 50° in dip angle, 80 to 240 m in width and 800–1000 m in strike length. The two orebodies are separated by a distance of 110–130 m. Production with block caving originally, ie Phase 1 project started at Tongkuangyu from the first undercut at a depth of 200–300 m below the ground surface and designated as Lift 810 m in late 1989 and has continued to the present. During the last 25 years Tongkuangyu has mined three lifts: Lifts 810 m, 690 m and 530 m. The previous two lifts utilised a slusher process with an annual designed production rate of 4 Mt. In this context the lift name represents the elevation of track haul level.The Tongkuangyu Phase 2 project serves for two lifts (ie Lift 530 m and 410 m) under the elevation of 690 m and the annual designed production rate is 6 Mt. Since the orebody is approximately 50° in dip angle, it is originally designed that production at Lift 530 m is comprised of one main extraction level and two auxiliary extraction levels in the footwall and undercutting is started from one end of the extraction footprint forward to another end, which is from north-east to south-west.Production at Lift 530 m started from March 2011 and reached to 6.39 Mt in 2013 and 6.9 Mt in 2014. Additionally, Tongkuangyu improved block caving processes and used modern mining equipment, which differ from the previous two lifts. Blastholes for undercutting and drawbell-preparation are now drilled using jumbos. The blasted ore is transferred to the underground crushing station via 10 t electric load-haul-dumps (LHDs) and then delivered to surface via a belt conveyor 3200 m long.Due to increasing ground pressure, a consequence of mining depth increase, stress abutment and inadequate support, significant damage occurred at the Tongkuangyu Copper Mine with production at Lift 530 m. This resulted in significant production delays and rehabilitation costs. A series of improvements have since been implemented including an advanced undercut sequence and increased ground support. All of these improvements have allowed Tongkuangyu to alleviate ground control issues, reduce operating costs and ensure safe production.CITATION:Liu, Y M and Bian, K W, 2016. Production at Lift 530 m of Tongkuangyu Copper Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H von Blottnitz, J L. Broadhurst

Eco-efficiency has been proposed by the World Business Council on Sustainable Development as an environmental performance indicator framework that contributes to sustainability by assisting corporate decision makers improve the environmental performance of their operations and processes, while also extracting additional economic value. Given that the recent engagement of the minerals industry with sustainability has highlighted the need for requisite tools and methodologies, it is therefore of interest to assess whether eco-efficiency indicators can drive sustainability performance improvement during process design within the minerals industry. Previous work indicates that the choice of sustainability performance indicators to be used for decision making needs to be governed by the decision context; ie the performance indicators need to be fit-for-purpose. Here, the strengths and weaknesses of eco-efficiency indicators are analysed using case studies. First, a more rigorous definition of eco-efficiency indicators for the minerals industry is proposed based on indicators currently offered in the literature. Two case studies are then selected to reflect typical decision situations encountered within minerals process design. For each case study, eco-efficiency indicators are computed and are compared to more traditional graphical representations of the economic and environmental performance of process design alternatives considered. The sensitivity of these indicators to various process design parameters is also investigated. Results confirm that the meaningful application of eco-efficiency indicators is strongly dependent on the decision context in which the process data is generated. Results also show that eco-efficiency indicators can be related to technical process design parameters to allow for richer communication of performance information for various decision trade-offs; however, in some cases, graphical approaches that provide more insights into the environmental-financial trade-offs should be preferred. The research thus contributes to guiding the selection of the appropriate tools for more environmentally sustainable design of minerals beneficiation processes.

Jan 1, 2009

By J McCluskey, N Barros

"Long-term strategic planning at BHP Billiton’s Western Australia Iron Ore business aims for sustainable value maximisation of its large, long-life, low-cost, expandable mineral inventory and supply chain infrastructure. While mine plans are key components of this value equation, this objective requires a whole-of-business approach through comprehensive consideration and optimisation of the full value chain. Only through a system view do we believe that the value proposition of a set of plans is truly optimised.The fundamental considerations include: mineral inventory information, given its intrinsic uncertainty and risk/knowledge horizon a marketing view of future quality premium/discount based on overall market quality load whole of supply chain optimisation on a throughput accounting basis alternative sequences of capital decisions closure costs with significant magnitude of total movement requiring optimisation as part of the plan. In addition, the plan provides a view of acceptable uncertainty levels at different times in the future.BHP Billiton Iron Ore uses a structured Life of Asset planning process that supports the business with the optimisation of its maximum value proposition through a non-deterministic scenario-based optimisation approach on an annual basis. This is a key input to each year’s medium-term plans and budgets, including activities identified through a value of information approach that resolve the key uncertainties and steadily improve confidence in the plan.CITATION:McCluskey, J and Barros, N, 2014. Life of asset planning, uncertainty and value optimisation of the iron ore business – from exploration, to market, to closure, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By H Q. Zhang, M C Chai, W Fu, H Y Chen, L M. Wei, Q J. Yang

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Fozichong deposit – located in the south-western segment of the giant Qinhang metallogenic belt, South China – is a large-sized lead-zinc polymetallic deposit. This deposit contains two main ore districts, termed as the Guyi ore district in the north and the Hesan ore district in the south respectively. We present an integrated data set on sulfide minerals, fluid inclusions and stable isotope (H-O-S-Pb) geochemistry to better understand the features and genesis of the Fozichong deposit.Field and paragenetic relationships indicate three mineralisation stages forming the early (Po+Sp+Gn+Ccp+Py+Di+Ep+Qtz), middle (Sp+Gn+Ccp+Py+Ep+Chl+Qtz) and late (Gn+Sp+Py+Qtz+Cal) sulfide assemblages respectively. Mineral chemistry – particularly S/Fe and Co/Ni ratios in pyrite, Zn/Fe, Zn/Mn and Zn/Cd ratios in sphalerite and Pb/Ag ratios in galena – indicates a magmatic association for the sulfide minerals.Quartz and calcite coexisting with the sulfide minerals of various stages host abundant fluid inclusions. Quartz in the early stage contains two- or three-phase CO2-H2O and liquid-rich aqueous inclusions, which have homogenisation temperatures of 162~365°C and salinities of 2.9~17.8 wt per cent NaClequiv, whereas quartz and calcite from the middle and late stages are dominated by two-phase, liquid-rich aqueous inclusions that have slightly lower homogenisation temperatures (153°C~320°C) and much lower salinities (1.0~6.0 wt per cent NaClequiv). Hydrogen isotopes (dD = -59‰~-41‰), analysed using fluid inclusion waters from quartz and calculated oxygen isotopes (d18OH2O = -5.47‰~4.00‰) for the equilibrated ore fluids, indicate that the ore-forming fluids may have been sourced from magma and mixed with groundwater in the late stages. Sulfide minerals have d34S values of 2.3‰~4.3‰, consistent with a magmatic-derived source for sulfur. Lead isotopes (206Pb/204Pb = 18.592~18.794, 207Pb/204Pb = 15.648~15.864, 208Pb/204Pb = 38.909~39.580) confirm that lead and, by inference, zinc were mainly derived from magmatic rocks, with subordinate contributions from sedimentary rocks.Various lines of evidence support that the formation of the Fozichong deposit has close genetic association with the granite porphyry intruded in the late Yanshanian period (106 Ma), and it can be classified as a magmatic hydrothermal type lead-zinc deposit. We propose that the Hesan and Guyi ore districts may represent the proximal and distal products of a magmatic – hydrothermal system respectively.CITATION:Fu, W, Zhang, H Q, Chai, M C, Yang, Q J, Chen, H Y and Wei, L M, 2015. Genesis of the large-sized Fozichong lead-zinc polymetallic deposit, Guangxi, south China – constraints from the sulfide mineralogy, fluid inclusions and isotope geochemistry , in Proceedings PACRIM 2015 Congress, pp 609–614 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S DeKruijff

The Mount Isa Mines Copper Mine in Mount Isa started producing copper in 1966. The Copper Mine gradually increased production rates to nearly six million tonnes per year. Over the last three years the mine has been in a gradual ramp down due to the reduction of primary ore sources and head grade. The majority of ore sources are predominantly in pillar retreat sequences bounded by multiple fill masses. There also a substantial lower grade resource delineated to the south of the main orebody. These remaining ore sources present significant engineering challenges to obtain a safe and cost-effective extraction. Stope designs have become increasingly complex and require additional engineering and operations input and analysis. This paper describes the major planning and operational challenges and issues associated with the stope design and extraction of an orebody in the later stages of mine life.

Jan 1, 2000

The development of the Ballarat goldfield and of the city of Ballarat are a significant part of the history of the Australian mining industry. Important developments in technology, legislation and labour relations made their first Australian appearance in Ballarat. The growth of the city and its survival after the closure of the mines provide an interesting case study in the benefits flowing from a vigorous mining operation. The failure of the mines can be attributed to rising costs of materials and labour and declining manpower productivity at a time when the price of gold was not free to respond to changing market conditions. The curtailment of exploration programs and increasing labour unrest resulted from this situation, and made the closure of mines inevitable.

Jan 1, 1982