Search Documents

By Culshaw MG, Deaves AP, Bell FG

The accurate prediction both of the water ingress into sub-surface excavations and the nearby groundwater pressures is of fundamental importance to the control of the stability and flooding of tunnels or mines constructed below the water table. Predic- tions are usually based on laboratory and in situ permeability determinations together with observations of groundwater conditions in boreholes. Although established theoretical methods provide a basis for prediction, the actual ingress depends on many factors. The objective of this paper is to explore the geological controls on groundwater conditions, and the available methods of prediction of both groundwater flow and pressure are outlined. Salient points are emphasised by reference to a case history involving the construc- tion of a tunnel in a faulted and mixed sequence of sandstones, siltstones, shales and coals. Water ingress quantities have been monitored for a variety geological and geotechnical conditions including heavily faulted and mine disturbed ground. The overall results are discussed with reference to the relevant hydrological and geologi- cal conditions in terms of the geological structure, lithology and rockmass condition as well as the construction methods.

Jan 1, 1988

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

By Coppock BW

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By King RP, Kientzler P

In recent years, ultrasonic comminution technology has been developed at the Utah Comminution Center. An ultrasonic grinding device was assembled and investigated. An ultrasonic transducer system has been significantly improved by using a special type of piezoelectric ceramic and preloading to 4.1 x le kPa to obtain maximum strength. The improved system provides constant and rapid vibratory promotion of fatigue fracture resulting in more effective breakage. The design principles for an ultrasonic mill are developed in this paper. Size reduction was successfully achieved in the ultrasonic nip-roll device for a variety of materials. Ultrasonic comminution has repeatedly demonstrated the capability of producing fine particles from a variety of materials. A comparison between ultrasonic grinding and dry ball milling of limestone showed that the ultrasonic device produced much narrower size distributions than the ball mill. This trend is especially obvious in the coarse size range where few particles remain, and in the fine size range where overgrinding is prevented. This behavior might have some interesting applications in areas other than mineral processing like powder metallurgy or material science where narrow and controlled product sizes are required for the successful elaboration of high-technology ceramics and glasses. Ultrasonic comminution has a significant advantage in the accurate control of the product size.

Jan 1, 1993

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Lyman G. J

The volumetric distribution of valuable mineral, or phase, within a set of particles is called the liberation distribution. To optimise a mineral processing plant it is necessary to know the liberation distribution in most of the streams, especially those adjacent to separation devices. Possibly the most common method of analysing ore particles is to section sets of similarly-sized particles. However, the observed sections can appear liberated even if the particle is composite. This means that the 'apparent' liberation distribution can be very different to the 'actual' liberation distribution. This discrepancy is called stereological error. One must then somehow estimate the actual liberation distribution using the apparent liberation distribution. This problem is called the liberation distribution problem and its solution is the subject of this paper. The solution is based on a sorting algorithm which uses geometric probability equations. These equations are based on the assumption that sectioning is isotropic and uniform. Apart from these assumptions the equations are completely independent of particle shape or texture. The algorithm is verified by numerical simulation and experimental methods. For the numerical simulations the correspondence between the actual and estimated liberation distributions is excellent. For the experimental methods, the agreement is not as good and appears to be due to experimental errors.

Jan 1, 1995

By O Salisbury

Ingress of air into the longwall goaf environment needs to be managed appropriately to reduce the risk of creating a spontaneous combustion event. The maingate goaf edge is an area of particular concern in this respect, as air often penetrates for some distance into the goaf along this region inbye of the longwall face. Since the flow rate in this part of the goaf is also quite low, an opportunity exists to disrupt the air pathway by implementing a barrier to the airflow. Previous attempts using plugs made from an assortment of materials have resulted in varying degrees of success. More recently, Narrabri Coal Operations (NCO) has introduced the use of a chemical foam that is mixed with nitrogen to produce a standing barrier with the consistency of shaving cream. The implementation of this practice has consistently proven to be very effective for reducing the oxygen concentration along the maingate goaf edge by systematically retreating the foaming unit with the longwall. This paper presents how the foam is applied in the underground goaf environment to prevent oxygen ingress and uses results from gas monitoring to confirm the foam effectiveness.

Oct 12, 2022

Despite the research interest on non-cyanide gold lixiviants over the past three decades all the non-cyanide gold processes are still at the developmental stages with limited understanding on solution and pulp chemistry in some cases. This is partly associated with:the difficulties in measuring reliable equilibrium data for various gold(I/III) complexes with non-cyanide ligands; the lack of knowledge on mixed-ligand complexes; and different kinetic stabilities of gold(I) complexes with respect to disproportionation. This paper presents reliable equilibrium data for complex formation, dissolution, precipitation, hydrolysis and disproportionation reactions of gold(I/III) compounds with a range of non-cyanide ligands: S2-, HS-, S2O32-, SO32-, SCN-, SC(NH2)2, OH-, NH3, Cl-. Solubility of gold(III) compounds with non-cyanide ligands follows the order: Cl- > NH3 > OH-. In the case of gold metal the solubility order at a given temperature is MgS > Fe(III) or Cu(II) / Cl- > Cu(II)/NH3 > NaOH, but the solubility increases with increasing temperature. Rate of gold oxidation with different non-cyanide lixiviants depends on the oxidant, ligand and temperature and follows the general order of oxidants: Fe(III) or Cu(II) > X2 or OX- > O2 (X = halogen). In the case of metal ion oxidants oxygen is required to reoxidise Cu(I) or Fe(II). Some of the reported data on chloride and thiosulfate leaching of gold are presented to highlight the effect of additives and the copper, silver and sulfur contents of the starting material on the success of non-cyanide leaching processes.

Jan 1, 2004

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

The high cost of sampling systems is largely due to the fact that indiv- idual mechanical type sampling units must be installed at the discharge end of ore/pulp pipelines, that is, at points where the pipeline discharges into pump sumps or the like. A considerable economic advantage may be obtained in the use of a samp- ling device that can be installed at any point in the path of the trans- porting pipe line. Initial tests on a vertical line with an injection sampler using iron ore concentrates reveal the validity of this type sample versus that taken with a mechanical sampler. A descrip- tion of the injection sampler shows its simplicity of installation, requir- ing minimum downtime on existing lines.

Jan 1, 1976

By Pratt V, Davis K

Challenges facing middle management in the 1980's and beyond are not confined to business matters such as industrial relations, government and legal constraints, corporate takeovers, and commodity marketing. More particularly they deal with people issues and the interrelationship of corporate/ family relationships. There is a need for corporations to acknowledge the growing conflict between corporate/family roles being brought about by such matters as equal opportunity, double professional marriage partnerships, personal mobility and the increasing stress faced by managers as a result of current demands and expectations being placed on them. While the main responsibility for managing professional life as well as the relationship between professional and private life rests with the individual executive, corporations nevertheless have a major responsibility to assist these executives in this management process. Corporations in Australia are taking steps to address this situation but much more needs to be done. This was highlighted in the March 1985 "Middle Management" course with its associated Spouses Programme presented jointly by Australian Mineral Foundation and The Australian Administrative Staff College. Effective communication is at the heart of the matter but no amount of training on this subject will bear fruit unless there is an associated commitment by executives to improve the effectiveness of their communi- cation process both in their corporate and family roles.

Jan 1, 1986

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

Total extraction is a misnomer and invariably some coal losses occur in the mining of pillars. "Fulls" pillar extraction is by the pocket and fender method, the splitting method or the open end method, with extraction in the pillar, and in rows of pillars in planned sequence, using combinations of coal and timber and roof-bolts for support. Where circumstances dictate, partial extraction is used, leaving behind portions of pillars in large blocks for support. The use of such extraction plans and supports as minimum guidelines has contributed greatly to safety in United States Coal Mines.

Jan 1, 1974

By Toguri JM

A solid electrolyte technique has been used to measure the activity of cobalt in liquid cobalt-gold alloys containing between 0.085 and 0.50 mole fraction of cobalt, and for temperatures from just above the liquidus to around 1550 K. The system exhibits positive deviation from ideality, both in the activities of cobalt and gold, and in the enthalpy and excess entropy of mixing. The results agree with previous measurements using a Knudsen cell - mass spectrometer technique, but differ from those reported for a gas equilibration method. The data have been used to calculate the activity coefficient of cobalt oxide in silica saturated iron silicate slags and to express the solubility of cobalt in such slags as a function of cobalt activity and oxygen pressure.

Jan 1, 1984

The paper describes the geotechnical as- pects of design and construction of two 12 m diameter concrete lined tunnels from the start of design to completion of construction. Prob- lems occurred due to delay in supply of essen- tial rock support materials from overseas and alternative methods using locally available materials were developed. Several major rock- falls and rock movements occurred and remedial measures are outlined.

Jan 1, 1981

The difficulty in creating and obtaining a competitive edge in the mineral industry is rapidly increasing. The Kiruna Iron Ore Mine in the far north of Sweden is currently thriving on the world market through firm managerial strategy. LKAB believes in upgrading its raw material to produce a high quality iron ore product for sale to steelworks throughout the world. It is vital that this product is also of uniform quality and quantity to provide quality assurance to customers. The first link in meeting these product requirements starts in the underground workings. Mining methods and operations are of large-scale. Automation and continuous production streamline operations and reduce operating costs. These factors have built Kiruna Iron Ore Mine into the world's biggest, most modern, underground iron ore mine. To remain competitive on the world market, LKAB relies heavily on research and development. The mine is currently in a phase of upgrading its operations. A 25-tonne Toro electric loader is being tested to improve the rate of output of ore from the mine. Long hole drills are being improved to increase accuracy and efficiency. An electronic detonating system will improve detonator delay precision. Projects are underway to better understand ore flow mechanisms from a caving orebody. Benefits include improved ore recovery along with better rock quality control at the caving front. The continued updating of mining operations at Kiruna will enable LKAB to continue to maintain its competitive advantage on the world market in the production of high quality iron ore products.

Jan 1, 1997

In response to requests from the iron ore mining industry, the Commonwealth Scientific and Industrial Research Organisation (CSIRO) Division of Mineral Physics has developed a number of bulk analysis techniques in which analyses are obtained directly from ore samples weighing many kilograms or from ore located on conveyor belts.Because penetrating neutron and gamma radiation is used, measurements are obtained from a large volume of ore, which ensures thal the analyses are represelllative of the bulk.Two different gamma-ray techniques have been developed to measure iron ore grade. The first is based on backscallering of 60CO gamma rays, while the second involves measurement of the annihilation radiation which arises when the ore is irradiated wilh 226Ra gamma rays. Both techniques measure the iron concentration with an accuracy (1 s) of better than 0.4% Fe.A thermal-neutron irradiation technique using a 252Cf neutron source has been developed for the simultaneous determination of iron and the aluminium impurity (expressed as AI2O3) in iron ore fines on a conveyor bell. Because the conveyor speed must not exceed about 0.05 m/s, if good accuracy for AI2O3 is required, an auxiliary analysis bell is required Lo avoid inLerference with normal ore processing. Dynamic trials have demonstrated that accuracies of 0.6% Fe and 0.1% AI2O3 can be obtained.

Jan 1, 1985

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974

This paper is written as a supplement to that of Edwards, Baker and Knight on "The Geology of the Wonthaggi Coalfield" 1, the West Area pit being in an early developmental stage at the time of their paper. The thin seams to the west of Dudley Basin 2 had beenknown for many years but it was not until 1935 that it became necessary to work them. The West Area Pit came into production as Dudley Area Pit approached exhaustion in 1937. From available information it was estimated that early work would be in a 36in. bottom seam. The present top seam was not included in the reserves, but it was to be extracted where it proved thick enough for economical working.THE SEAMSEdwards, Baker and :Knight (1944) had insufficient information to correlate positively the West Area seams with those in the Dudley Basin. Their opinion was, however, that they were a westerly extension of the Bottom Seam. Since then the driving of the present north-east heading towards No. 4 Bench McBride Tunnel has established that the West Area seams are those worked as Bottom Seam in the Dudley Basin. West Area Top Seam is a seam that occurred above the Bottom Seam in the Dudley Basin. Only sporadic attempts have been made to work it in Central Area, because 30in. was considered an economic minimum height until recent times. This seam should not be confused with Top Seam, Dudley Basin, which lies some 300ft. above the bottom seam measures and except in isolated areas over deeper workings has been eroded away in West Area.

Jan 1, 1953

By Hughson B

At present sane man-made Improvements and natural features are constraints on unlimited underground mining. 7 hey will continue to remain, as constraints on the future high production mining systems as wall. Unless these constraints are overacTe by research, where possible, future high production systems may became unacceptable. 7 he areas of future research include improved subsidence prediction techniques applicable to future mining systems, subsurface subsidence behaviour, mining systems capable of producing no surface subsidence and subsidence damage assessment.

Jan 1, 1988