Search Documents

By Nixon TR

The Australian Coal Industry Research Laboratories Ltd. (A.C.I.R.L.) MINVENT computer program can be used to simulate existing and projected colliery ventilation requirements. New collieries can be planned using a database of ventilation parameters which were ascertain- ed by A.C.I.R.L. surveys at selected collieries in N.S.W. and Queensland. Several techniques are used in both the formulation of the database and in the evaluat- ion of a ventilation system, prior to analysis by the MINVENT program. The analysis of a ventilation system requires the measurement of air quantities, pressures and hence airway resistances. All resistances are calculated at standard air density of 1.205 kg/m3. Air densities are derived from barometric pressure and wet and dry bulb temperature readings. Airway frictional and shock losses, leakage through stoppings and overcasts, flow of air through regulators, face resistance and resistance of anomalous ventilation features are related to the typical Australian measured data presented.

Jan 1, 1983

By A Halim

"There is still debate about who should ultimately be responsible for the ventilation system in anunderground mine. The Queensland Coal Mining Safety and Health Regulation 2001, states that adedicated ventilation offi cer is the person, while Western Australian Mines Safety and InspectionRegulation 1995 states that it is the mine manager who is responsible; the ventilation offi cer actsas the managerÆs principal ventilation advisor. This paper outlines a comparison between bothapproaches."

Jun 1, 2012

By Shoobridge PH, Firkin GR

The Imperial Smelting Process blast furnace (ISF) of the Sulphide Corporation Pty Limited zinc/lead smelter at Cockle Creek, New South wales, has in recent years greatly increased its consumption of low grade feed materials, and as a consequence has experienced periods of unstable furnace operation. Routine examination of production sinter, including softening characteristics and micro- examination, showed that the problems had been caused by an increasing silica content in sinter. The silica entered a low melting point glass phase containing calcium and lead oxides. The relative volume of this phase increased until it formed a continuous matrix in the sinter structure and this made the sinter more likely to soften at lower temperatures. Premature softening caused loss of operating stability in both the shaft and hearth of the ISr. The required sinter structure for ISF smelting was found to consist of a network of intermeshing, refractory crystals which provided skeletal strength for sinter lumps even after the glass phases had begun to soften and melt. With an understanding of the importance of microstructure and softening temperature of zinc/lead sinter and the progressive identification of those factors in sinter production which affect the microstructure, a significant improvement in stability of operations has been possible.

Jan 1, 1980

By Z Gao, D Liao, W Sun, S G. Pooley, J Wang, Z Shi, G Jing, S Ren, Q Chen

Yuanjing processing plant is a scheelite and wolframite plant in southern China. Water shortages and recent environmental regulations mean that the plant must reuse the wastewater that comes from the mining operation. This paper describes the efforts to reuse the mining and ore washing wastewater (MOW) in the processing plant. Initial attempts to reuse the MOW in the strong magnetic separation were unsuccessful because the magnetic media pack was seriously fouled by the micro-fine precipitate generated. The focus changed to reuse the MOW in the scheelite flotation circuit, which includes one roughing, one cleaning and three scavenging steps. Laboratory batch tests showed this would likely be successful because using MOW reliably improved the flotation performance in the laboratory tests. Then a 20 day industrial trial was run in the plant. The trial was very successful with the enrichment ratio of WO3 increasing from 17.4 to 23.6, while the recovery remained around 79.2 per cent. The industrial trial was so successful the company immediately adopted the new scheme, which has remained in use ever since. This technical solution not only alleviated serious water shortages, and satisfied environmental regulations but also improved the plant performance.

Aug 24, 2022

By Kramadibrata S

Over the years many attempts have been made to develop a means of assessing the excavatability of rock. Most of them are based on an empirical rating system while some authorities still propose the use of seismic velocity as a direct predictor of the rippability of a rock mass. On the other hand there are a number of classical models which have been developed to define the cutting force required at the pick or tooth of continuous miners.While these methods have been applied with various degrees of success to the design of excavation systems there is no generally acceptable method of defining the excavatability or cuttability of a rock mass in terms of the machine power required to generate a particular rate of production.The authors have attempted to overcome this deficiency by recording the intact and rock mass properties at a number of surface mines where continuous miners were in use and to use this data to examine the relationships between the relevant dimensionless groups developed from a dimensional analysis of the problem.The results obtained are encouraging and it appears that this new approach to the problem could lead to civil and mining engineers having a means of predicting the cutting power required to excavate rock at a given rate at any site.While this paper does not include a review of past work it refers to a number of key publications which will give the reader an excellent introduction to the subject.It is important to point out that the research work reported in this paper is part of a doctoral research project at Curtin University of Technology on the Influence of Intact Rock and Rock Mass Properties on the Design of Surface Mines. One of the major objectives of this project is to explore the possibility of developing a technique for predicting the excavatability of rock in surface mines at the design stage.This paper therefore commences with a brief reference to the continuous surface miners in use at the test sites followed by some original work by the authors in applying Dimensional Analysis to analyse the macro-performance of mechanical excavators. Following an analysis of the experimental data the authors validate the wider use of the model by referring to its successful application in predicting the power required to excavate rock by continuous surface miners at other sites.

Jan 1, 1995

By Abell RS, Wyborn D, Solomon M, Stuart-Smith PG, Henderson GAM

The two major massive sulphide deposits in the Silurian rocks of southern NSW, Captains Flat and Woodlawn, differ from classical Kuroko deposits in several ways, e.g. they lie on the flanks of felsic volcanic piles in volcano-sedimentary marine sequences, are relatively thin and large compared to individual Kuroko deposits, show prominent banding in lead-zinc ore, and contain arsenopyrite. Qualified stuctural and stratigraphic correlations of the various fault-bounded remnant Silurian sequences that host these deposits provide the basis for a new interpretation of the regional geological setting that also differs from that of the Kuroko deposits (Ohmoto, Tanimura, Date, Takahashi, 1983), and sheds further light on the distribution of volcanogenic massive sulphide deposits in the Silurian rocks of NSW.

Jan 1, 1987

By A J. Weston

Block or panel caving technology is far removed from that of the top slicing and block caving of the late nineteenth or early twentieth centuries. The rapid mechanisation and expansion of these methods in the late twentieth century was as much a result of the change of the technology of the unit operations of development, ground support, drilling and blasting and transport as it was of the advances in geotechnical understanding and practice. The small footprint gravity and scraper block caving mines with boundary weakening, rail transport and shaft hoisting of the early to mid-twentieth century have been replaced by massive high lift panel caves using preconditioning of the ore, large load-haul-dump units, adjacent crushers and conveyors to surface. The technology changes in the unit operations are described and the drivers for these changes examined.CITATION:Weston, A J, 2016. The evolution of block caving technology, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 265–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Lloyd F, Bayley F. J

The new South Mine in the Western Deep Levels complex is destined to become an ultra deep project extending to depths of 4 200 m below surface and where rock temperatures are likely to exceed 65 ¦C. Initial estimates put refrigeration requirements at 133 000 kWR. A surface refrigeration plant with an initial capacity of 42 000 kWR has been commissioned and will be used for mining the upper levels.

Jan 1, 1988

By Sagrabb T

In a company's quest for financing the development of a new mine, it will make calls on stockbroking houses and banks. The choice of the best-fit broker or banker is of great importance, and in the case of the miner, this is a house that has an intimate understanding of the mining industry, particularly one that has a solid staff complement of personnel with operating mine experience at a senior level. The most important document that the company will present to support its financing request will be the Feasibility Study. It cannot be too strongly emphasised that this document must be absolutely comprehensive and cover items including: (a) Geological review; (b) Resources and reserves; (c) Mineability; (d) Mining schedule; (e) Metallurgy; (f) Process plant description; (g) Infrastructure and services; (h) Management and operations; (i) Environmental and social impact; (j) Capital costs; (k) Operating costs; and (1) Financial analysis. The elements listed above represent major topics and require a great deal of expansion in the body of the document. Rothschild Australia Limited assists its client companies by supplying a detailed framework so that they will be in a position give the bank the information it needs to complete its technical `due diligence' study within a mutually agreed time. The client company will advance its position markedly if it uses well-known, reputable consultants to either complete or assist with the various aspects of the Feasibility Study. Such an approach will give the potential financier confidence that the company has taken a professional and unbiased attitude in determining the feasibility of the property in question. Most small- to medium-sized mining companies, both within Australia and overseas, will prefer, or will find it mandatory, to request a project funding package rather than opt for a corporate loan. This is because the company either does not want to tie all of its assets to the performance of one project, or that it is a one or two project company with no other substantial assets and is therefore unable to obtain a corporate loan. Upon receipt of the Feasibility Study, the bank will use the data supplied by the company in its cash flow analysis to build its own financial model. The purpose of this is to examine the timing of

Jan 1, 1994

The King River Power Development on the West Coast of Tasmania has involved the storage of the waters of the King River in the new Lake Burbury and their diversion through a 7 km tunnel to a 144 MW power station. The last kilometre of this tunnel descends through 160 m under a ridge before emerging from the bank of the King River at the power station site. The decreasing cover over the tunnel as it approaches the power station meant that a steel lining was required in the last few hundred metres of the tunnel. This paper describes the geotechnical investigations which were carried out to establish the necessary length of the steel lining.

Jan 1, 1993

By Fowke NC, Williams RJ, Hungerford F

In-seam, directional drilling has been implemented at Huntly West Mine, New Zealand as the most cost effective means of obtaining geological information at a level of detail and accuracy required for planning of longwall ("flexiwall") panels. No geological or geophysical technique tried at the mine prior to 1989 has been able to reduce geological risk to an acceptable level. Surface and in-seam seismic methods have not had adequate resolution. Obtaining the required knowledge via surface drilling would be prohibitively costly, and still not precisely locate or orient faults or the axes of seam "ridges and valleys".A total of 3543 m was drilled at an average of 67m/shift including setting up time. Unplanned delays totalled only 9.6 percent. Major re-interpretation of seam structure resulted from the drilling. Lateral and longitudinal panel grades have been defined. which should be negotiable with the Coalcorp longwall equipment.

Jan 1, 1991

The fast rate of development in the micro technology industry is enabling computer based systems to be used in ways never considered before. Micro technology can be used to great advantage in the mining industry to improve both safety and productivity. The planned use of electronic 'IN/OUT' boards at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) mines will provide a much improved system for checking that the mines are clear before firing. The provision of remote ocaputerised core logging facilities made possible by small remote data entry terminals will greatly improve the productivity of the personnel involved in all stages of core Logging.

Jan 1, 1983

A critical appraisal of the wide variety of processes used in the pyrometallurgical production of metals and non-metals shows that there is a strong physico-chemical and, in particular thermodynamic, basis for the variety. Based on this, a simple classif- ication scheme has been developed which makes it possible to understand the methods for extracting individual metals and non-metals pyrometallurgically and to assess which are the more attractive routes. The analysis presented shows why there are essentially two broad routes for pyrometallurgical production of metals and non-metals; viz., the reduce- refine and the refine-reduce routes. Halides have the role in pyrometall- urgical processing of producing pure compounds for subsequent reduction. The criteria which determine the selection of reduction method for oxide raw materials and intermediate halides (e.g., use of carbon, hydrogen, a more reactive metal or electrowinning) are examined critically in the paper. The treatment of sulfide raw materials is considered also, particularly the criterion for smelting sulfides directly to the metal.

Jan 1, 1987

By Batterham R. J

Some developments in copper, lead and zinc extractive metallurgy which have gone in to production or seem to be close to production scale are described with emphasis on why these innovations have been adopted.Mineral processing operations are now using: automated quantitative mineralogy,high capacity fine crushing equipment, ò fine grinding equipment, andcolumn cell flotation.Extractive metallurgy plants are using:ò bath smelting of concentrate at various scales, and ò flash converting of copper.Hydrometallurgical process developments are slower to make a commercial impact. Concerns about ability to handle impurities in the feed and production of saleable by-products are often major hurdles.An expression for the probability of implementing the first example of a new development is presented.

Jan 1, 1992

By R Crosbie, K C. Runge, E Tabosa, J K. McMaster

Flotation feed density is an operating parameter which is currently not well understood. Most models of flotation only incorporate its effect on particle residence time, but it is likely to have additional effects within both the pulp and froth phases of the machine. Test work was performed in MetsoÆs 3 m3 RCS test rig to investigate the effect of flotation feed density on metallurgical performance. The rig was operated at Rio TintoÆs Northparkes operation using flotation feed and scavenger tail. For each feed, tests were performed at different feed densities, and measurements were performed to estimate the pulp and froth recovery as well as other key flotation parameters (eg bubble size, turbulence and froth stability). Results of this test work have shown that the pulp density does affect key parameters of the flotation process in both the pulp and froth phases. Pulp phase kinetic rates decrease at high density and this is attributed to a reduction in the turbulence within the cell. Froth phase recovery, however, improves presumably because of a stabilising effect due to a greater loading of solids on bubble surfaces.There is a need for more research to be done to better understand these interactions so that metallurgists can determine the optimum flotation feed density to use at a particular operation, or within a section of a flotation circuit.CITATION:Runge, K C, Tabosa, E, Crosbie, R and McMaster, J K, 2012. Effect of flotation feed density on the operation of a flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The main aim of the conference is to work towards improved useage of steelplant slags which have largely been considered waste mater- ials, This paper summarised investigations carried out on the suitability of air cooled blast furnace slag, blast furnace granulated slag and basic oxygen steelmaking slag as road base materials. All slag samples were obtained from the PortòKembla Works of Australian-Iron and Steel Pty Ltd. Since road making materials are increas- ingly being characterised by use of resilient moduli, the compressive strengths and resilient moduli were determined for road base of the following slags. 1 Air cooled crushed blast furnace slag 2 mixes of air cooled blast furnace slag, granulated slag, and lime 3 mixes of air cooled blast furnace slag,-granulated slag and basic oxygen steelmaking slag. Evaluation of a local dacite (dense medium grained igneous rock, classification rhyolite), generally considered an excellent road base course material, was carried out for use as a reference material.

Jan 1, 1979

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976

The Imperial Smelting Process (ISP) for the simultaneous smelting of zinc and lead was developed at Avonmouth from the 1930's with activity intensifying in the late 1940's/early 1950's. Present operations are based around the No.4 furnace which was built in 1967. Development during the 1980's has been driven by the need to sustain operations at low metals prices and has been aimed at reducing manning whilst increasing output. Although hit by several major plant disruptions, progress has been steady, culminating in a ú10 million capital programme in 1988?89 to upgrade the operation. The most important technical developments, reflecting the needs of the 1990's have, in the sintering area, included improvements to feed conditioning and sinter quality, a 20% uprate in production capacity by debottlenecking, and pilot work leading to the installation of a Boliden-Norzink mercury removal plant. In the smelting area the ISP furnace has been rebuilt, with a redesigned bottom section to eliminate earlier operating sensitivities, and to achieve higher blowing capability, and at the zinc refinery the columns have been rearranged for more flexible operation and higher capacity.

Jan 1, 1989

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011