Search Documents

By Liu Y, Campbell K. R

The paper shows how breakage parameters may he extracted from laboratory batch grinding results and how they may used with reference full-scale hall mill circuit data to estimate the likely size distributions of values and gangue in a full-sca

Jan 1, 1997

By Shoobridge PH, Firkin GR

The Imperial Smelting Process blast furnace (ISF) of the Sulphide Corporation Pty Limited zinc/lead smelter at Cockle Creek, New South wales, has in recent years greatly increased its consumption of low grade feed materials, and as a consequence has experienced periods of unstable furnace operation. Routine examination of production sinter, including softening characteristics and micro- examination, showed that the problems had been caused by an increasing silica content in sinter. The silica entered a low melting point glass phase containing calcium and lead oxides. The relative volume of this phase increased until it formed a continuous matrix in the sinter structure and this made the sinter more likely to soften at lower temperatures. Premature softening caused loss of operating stability in both the shaft and hearth of the ISr. The required sinter structure for ISF smelting was found to consist of a network of intermeshing, refractory crystals which provided skeletal strength for sinter lumps even after the glass phases had begun to soften and melt. With an understanding of the importance of microstructure and softening temperature of zinc/lead sinter and the progressive identification of those factors in sinter production which affect the microstructure, a significant improvement in stability of operations has been possible.

Jan 1, 1980

By Kramadibrata S

Over the years many attempts have been made to develop a means of assessing the excavatability of rock. Most of them are based on an empirical rating system while some authorities still propose the use of seismic velocity as a direct predictor of the rippability of a rock mass. On the other hand there are a number of classical models which have been developed to define the cutting force required at the pick or tooth of continuous miners.While these methods have been applied with various degrees of success to the design of excavation systems there is no generally acceptable method of defining the excavatability or cuttability of a rock mass in terms of the machine power required to generate a particular rate of production.The authors have attempted to overcome this deficiency by recording the intact and rock mass properties at a number of surface mines where continuous miners were in use and to use this data to examine the relationships between the relevant dimensionless groups developed from a dimensional analysis of the problem.The results obtained are encouraging and it appears that this new approach to the problem could lead to civil and mining engineers having a means of predicting the cutting power required to excavate rock at a given rate at any site.While this paper does not include a review of past work it refers to a number of key publications which will give the reader an excellent introduction to the subject.It is important to point out that the research work reported in this paper is part of a doctoral research project at Curtin University of Technology on the Influence of Intact Rock and Rock Mass Properties on the Design of Surface Mines. One of the major objectives of this project is to explore the possibility of developing a technique for predicting the excavatability of rock in surface mines at the design stage.This paper therefore commences with a brief reference to the continuous surface miners in use at the test sites followed by some original work by the authors in applying Dimensional Analysis to analyse the macro-performance of mechanical excavators. Following an analysis of the experimental data the authors validate the wider use of the model by referring to its successful application in predicting the power required to excavate rock by continuous surface miners at other sites.

Jan 1, 1995

By Abell RS, Wyborn D, Solomon M, Stuart-Smith PG, Henderson GAM

The two major massive sulphide deposits in the Silurian rocks of southern NSW, Captains Flat and Woodlawn, differ from classical Kuroko deposits in several ways, e.g. they lie on the flanks of felsic volcanic piles in volcano-sedimentary marine sequences, are relatively thin and large compared to individual Kuroko deposits, show prominent banding in lead-zinc ore, and contain arsenopyrite. Qualified stuctural and stratigraphic correlations of the various fault-bounded remnant Silurian sequences that host these deposits provide the basis for a new interpretation of the regional geological setting that also differs from that of the Kuroko deposits (Ohmoto, Tanimura, Date, Takahashi, 1983), and sheds further light on the distribution of volcanogenic massive sulphide deposits in the Silurian rocks of NSW.

Jan 1, 1987

A critical appraisal of the wide variety of processes used in the pyrometallurgical production of metals and non-metals shows that there is a strong physico-chemical and, in particular thermodynamic, basis for the variety. Based on this, a simple classif- ication scheme has been developed which makes it possible to understand the methods for extracting individual metals and non-metals pyrometallurgically and to assess which are the more attractive routes. The analysis presented shows why there are essentially two broad routes for pyrometallurgical production of metals and non-metals; viz., the reduce- refine and the refine-reduce routes. Halides have the role in pyrometall- urgical processing of producing pure compounds for subsequent reduction. The criteria which determine the selection of reduction method for oxide raw materials and intermediate halides (e.g., use of carbon, hydrogen, a more reactive metal or electrowinning) are examined critically in the paper. The treatment of sulfide raw materials is considered also, particularly the criterion for smelting sulfides directly to the metal.

Jan 1, 1987

The main aim of the conference is to work towards improved useage of steelplant slags which have largely been considered waste mater- ials, This paper summarised investigations carried out on the suitability of air cooled blast furnace slag, blast furnace granulated slag and basic oxygen steelmaking slag as road base materials. All slag samples were obtained from the PortòKembla Works of Australian-Iron and Steel Pty Ltd. Since road making materials are increas- ingly being characterised by use of resilient moduli, the compressive strengths and resilient moduli were determined for road base of the following slags. 1 Air cooled crushed blast furnace slag 2 mixes of air cooled blast furnace slag, granulated slag, and lime 3 mixes of air cooled blast furnace slag,-granulated slag and basic oxygen steelmaking slag. Evaluation of a local dacite (dense medium grained igneous rock, classification rhyolite), generally considered an excellent road base course material, was carried out for use as a reference material.

Jan 1, 1979

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976

By Lloyd F, Bayley F. J

The new South Mine in the Western Deep Levels complex is destined to become an ultra deep project extending to depths of 4 200 m below surface and where rock temperatures are likely to exceed 65 ¦C. Initial estimates put refrigeration requirements at 133 000 kWR. A surface refrigeration plant with an initial capacity of 42 000 kWR has been commissioned and will be used for mining the upper levels.

Jan 1, 1988

By Sagrabb T

In a company's quest for financing the development of a new mine, it will make calls on stockbroking houses and banks. The choice of the best-fit broker or banker is of great importance, and in the case of the miner, this is a house that has an intimate understanding of the mining industry, particularly one that has a solid staff complement of personnel with operating mine experience at a senior level. The most important document that the company will present to support its financing request will be the Feasibility Study. It cannot be too strongly emphasised that this document must be absolutely comprehensive and cover items including: (a) Geological review; (b) Resources and reserves; (c) Mineability; (d) Mining schedule; (e) Metallurgy; (f) Process plant description; (g) Infrastructure and services; (h) Management and operations; (i) Environmental and social impact; (j) Capital costs; (k) Operating costs; and (1) Financial analysis. The elements listed above represent major topics and require a great deal of expansion in the body of the document. Rothschild Australia Limited assists its client companies by supplying a detailed framework so that they will be in a position give the bank the information it needs to complete its technical `due diligence' study within a mutually agreed time. The client company will advance its position markedly if it uses well-known, reputable consultants to either complete or assist with the various aspects of the Feasibility Study. Such an approach will give the potential financier confidence that the company has taken a professional and unbiased attitude in determining the feasibility of the property in question. Most small- to medium-sized mining companies, both within Australia and overseas, will prefer, or will find it mandatory, to request a project funding package rather than opt for a corporate loan. This is because the company either does not want to tie all of its assets to the performance of one project, or that it is a one or two project company with no other substantial assets and is therefore unable to obtain a corporate loan. Upon receipt of the Feasibility Study, the bank will use the data supplied by the company in its cash flow analysis to build its own financial model. The purpose of this is to examine the timing of

Jan 1, 1994

The Imperial Smelting Process (ISP) for the simultaneous smelting of zinc and lead was developed at Avonmouth from the 1930's with activity intensifying in the late 1940's/early 1950's. Present operations are based around the No.4 furnace which was built in 1967. Development during the 1980's has been driven by the need to sustain operations at low metals prices and has been aimed at reducing manning whilst increasing output. Although hit by several major plant disruptions, progress has been steady, culminating in a ú10 million capital programme in 1988?89 to upgrade the operation. The most important technical developments, reflecting the needs of the 1990's have, in the sintering area, included improvements to feed conditioning and sinter quality, a 20% uprate in production capacity by debottlenecking, and pilot work leading to the installation of a Boliden-Norzink mercury removal plant. In the smelting area the ISP furnace has been rebuilt, with a redesigned bottom section to eliminate earlier operating sensitivities, and to achieve higher blowing capability, and at the zinc refinery the columns have been rearranged for more flexible operation and higher capacity.

Jan 1, 1989

The King River Power Development on the West Coast of Tasmania has involved the storage of the waters of the King River in the new Lake Burbury and their diversion through a 7 km tunnel to a 144 MW power station. The last kilometre of this tunnel descends through 160 m under a ridge before emerging from the bank of the King River at the power station site. The decreasing cover over the tunnel as it approaches the power station meant that a steel lining was required in the last few hundred metres of the tunnel. This paper describes the geotechnical investigations which were carried out to establish the necessary length of the steel lining.

Jan 1, 1993

By G Harbort, D Clarke, D Morgan, C Sola

Northparkes Mines commenced production in 1994 and the mine has significant reserves to allow operation into the future. There are a number of potential future concentrator feed sources with variable sulfide mineralogy and grades.In February 2012 a comprehensive flotation survey was conducted to allow mass balancing and evaluate the operation of the flotation circuit. A rudimentary, copper element only, unsized flotation simulator was developed to evaluate high level potential for optimisation and improvement. In 2013 this flotation model was expanded to produce a mineral based, floatability component model to estimate the effect of future concentrator feed source on metallurgical performance. This revised model allows various circuit configurations to be simulated to provide a high level blueprint for the long-term planning to maximise performance.This paper provides a review of the process followed to develop the model, including an analysis into the mineral floatability component model and its calibration against plant operations. The effect of varying feed mineralogy and feed quality on future performance has allowed an internal review of potential circuit changes needed to accommodate the changing future feed.CITATION:Clarke, D, Harbort, G, Morgan, D and Sola, C, 2014. Northparkes Mines – flotation and planning for the future, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 203–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Fowke NC, Williams RJ, Hungerford F

In-seam, directional drilling has been implemented at Huntly West Mine, New Zealand as the most cost effective means of obtaining geological information at a level of detail and accuracy required for planning of longwall ("flexiwall") panels. No geological or geophysical technique tried at the mine prior to 1989 has been able to reduce geological risk to an acceptable level. Surface and in-seam seismic methods have not had adequate resolution. Obtaining the required knowledge via surface drilling would be prohibitively costly, and still not precisely locate or orient faults or the axes of seam "ridges and valleys".A total of 3543 m was drilled at an average of 67m/shift including setting up time. Unplanned delays totalled only 9.6 percent. Major re-interpretation of seam structure resulted from the drilling. Lateral and longitudinal panel grades have been defined. which should be negotiable with the Coalcorp longwall equipment.

Jan 1, 1991

The fast rate of development in the micro technology industry is enabling computer based systems to be used in ways never considered before. Micro technology can be used to great advantage in the mining industry to improve both safety and productivity. The planned use of electronic 'IN/OUT' boards at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) mines will provide a much improved system for checking that the mines are clear before firing. The provision of remote ocaputerised core logging facilities made possible by small remote data entry terminals will greatly improve the productivity of the personnel involved in all stages of core Logging.

Jan 1, 1983

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By Batterham R. J

Some developments in copper, lead and zinc extractive metallurgy which have gone in to production or seem to be close to production scale are described with emphasis on why these innovations have been adopted.Mineral processing operations are now using: automated quantitative mineralogy,high capacity fine crushing equipment, ò fine grinding equipment, andcolumn cell flotation.Extractive metallurgy plants are using:ò bath smelting of concentrate at various scales, and ò flash converting of copper.Hydrometallurgical process developments are slower to make a commercial impact. Concerns about ability to handle impurities in the feed and production of saleable by-products are often major hurdles.An expression for the probability of implementing the first example of a new development is presented.

Jan 1, 1992

Stope filling practice on the Great Boulder Mine was described in -a paper published in Aus.I.M.M., Proceedings No. 137, in 1945. When the paper was presented the process had emerged from the experimental stage, most of the initial operating difficulties had been overcome, and it had been established that this method of filling was suitable for the working of ore bodies in the Kalgoorlie field: Since 1945, it has fulfilled its early promise, -and during 1947, the tonnage of fill placed was sufficient to cover current operating requirements as called for by the mine ore breaking programme. The object of this paper is to outline current operations. In so doing it will refer' to some ground covered by the previous paper, but will omit details of the initial experimental work. It will include, however, a description of further experimental work on the use of hydraulic filling for worked-out shrinkage stopes, arid will provide more accurate data on costs than were available previously.ESTIMATE OF TONNAGE OF FILL REQUIRED.Early in 1946, the mine ore reserves were analysed in order to estimate the relative tonnages to be mined per four-weekly period by shrinkage stope methods -and by cut and fill stope methods respectively. This analysis was extended beyond the blocks already prepared for stoping, and inclqded the majority of the major ore blocks in the mine ore reserves. It gave the following results:-For a mill tonnage of 28,000 tons per period, 6,933 tons were required from cut and fill stopes, and a possible future maximum programme of 35,000 tons per period would require...

Jan 1, 1948

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020