Search Documents

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

Thank you for this opportunity to address your conference on The role of coal in the New Zealand energy market".New Zealand's energy market has, in common with much of New Zealand, undergone major change following the market reforms of the Labour Government.As far as the energy sector is concerned this change has been for the better, as it has created for the first time in a very long time a "true economic market" for energy in New Zealand.

Jan 1, 1990

By S Porter

The Melbourne City Link Project is a privately funded road infrastructure project linking three significant existing freeways in the vicinity of the Central Business District. The State Government, through the Melbourne City Link Authority, has contracted Transurban to build, own and operate City Link for a concession period of 34 years before the road network is transferred to the State. Transurban has a contract with Transfield Obayashi Joint Venture (TOJV) to design and construct the works. The project is divided into the southern and western sections and the tunnel works comprised the significant component of the Southern Link. Outside of the cut and cover tunnels at the portals, the driven tunnels component was constructed by TOJV direct labour. TOJV subcontracted all design work to a joint venture of Hyder Consulting and CMPS&F (Hyder/CMP). The geology in the tunnel corridor and generally below the city of Melbourne is highly variable and constantly changing. The tunnels were driven, for the most part, in siltstone and sandstone of the Silurian age, but also intersected overlying basalts and clays. The Silurian bedrock is a fractured aquifer that is connected to overlying alluvial aquifers. Consequently, the construction of the tunnels was a complex engineering task. This paper details the operational relationships and procedures developed to deliver a design that was aligned to the construction constraints and delivered an end product that met all technical, quality, cost and program goals.

Jan 1, 1999

By A G. L Pratt, M S. Kemp

BHP has used many innovative techniques when recruiting its workforce for the Cannington Project. Looking for a balance of experience and enthusiasm it was necessary to develop pre-selection tests to reduce the initial number of applicants to a manageable number for first interviews in Townsville. Success at this stage led to an applicant, and their spouse, to go through a second interview at the mine site. The full process from application to job offer took up to six months, but the results were felt to be worth the effort. The approach taken has resulted in a highly motivated and flexible workforce. This paper outlines the philosophies behind CanningtonÆs recruitment process, highlights some of the issues associated with the approach, and offers some measures of the outcomes.

Jan 1, 1998

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Knight

"In project evaluation there are two matters of keen interest to non-executive directors: the process by which an investment recommendation is reached, as well as the investment itself, as presented. It is sometimes mistakenly believed that Boards of directors are interested only in the result. That is not so. The process by which project evaluations are derived and socialised with the Board is as important as the result, sometimes more so.Setting aside the gloomy predictions of the doomsayers and looking through short-term volatility in supply and demand, the overall availability of mineral resources more often than not exceeds demand. There are in reality more development projects in prospect at any one time than are needed to meet the market. Only the fittest will prosper, although some others may survive.Optimism springs eternal in the mining industry and every project promoter, executive or entrepreneur has a convincing project development case. Some will create value for shareholders, but the historical evidence suggests that many will fail to meet the expectations set in their evaluation.Boards of directors make the final decision to invest, or not, in a new mine. Knowledge is power, and on that basis the balance of power favours management. Management has the facts (or in some cases, what passes for fact) and the passion to invest. The non-executives have the power of approval – yes or no – but before making a decision directors must demonstrate due diligence, the essential precursor to project approval.Management has a vital part to play in facilitating that due diligence process and in encouraging the independent thought processes of the Board. A closed approach by management fosters a negative, risk-averse attitude on the part of the Board. One that encourages an understanding of the rigour of the project evaluation process and the robustness of the result will allow directors to understand better the implications of their decision.CITATION:Knight, R, 2016. Project evaluation – a non-executive director’s perspective, in Proceedings Project Evaluation 2016, pp 11–19 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By N Weerasekara, M Bird, M Yahyaei, M M. Hilden, M S. Powell, J Franke, P Toor

The combination of new tools with a more rigorous approach to understanding the interaction of mill liners with overall mill performance and economics, forms the basis of an integrated approach to liner management. Based on accurate liner wear measurements, some (limited) physical mill inspections and surveys, accurate calibration of the mill load and analysis of process data, a whole new approach to liner selection, relining intervals and mill control is proposed. Collection and analysis of this information in operating mills illustrates the mill performance improvement which can be attained through this careful measurement and modelling approach.A more holistic approach to liner management is proposed, including a broadening of the current work to cover the potential benefits of improved relining technologies and predictive liner wear modelling. CITATION:Powell, M S, Hilden, M M, Weerasekara, N, Yahyaei, M, Toor, P, Franke, J and Bird, M, 2012. A more holistic view of mill liner management, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 95-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By R Carstens, L Munsamy, L Prinsloo, C Huang, C Zhang, R Liang, I Canbulat

With recent advances in machine learning, data-based automated decision-making has been proven successful with promising outcomes in many industries. Its application in the mining sector can be ground-breaking; particularly the data-driven analytics that can support decision-making in the mine and consequently enhance mine safety, efficiency and sustainability. However, the current data science applications in the mining industry are mostly noncomprehensive, especially inadequate in evaluations, thus often requiring further study to be potentially beneficial to operations. Furthermore, it was found that existing literature paid limited attention to understanding the role of such techniques. Hence, in this paper we aim to build an end-to-end machine learning powered data-driven framework for intelligent geo-hazard analytics to support decision-making for underground mining data management, where multiple types of data are managed in an integrated database to support the unified machine-learning model. Here we present the framework as data-driven workflow processes, including data gathering, data preparation, data processing and data presentation. In addition, we present an application scenario of the proposed framework, where falls of ground (FoG) is managed with the historical FoG investigation reports, related panel hazard ratings, compliance data and rock mass characteristics. A demonstration can be dynamic forecasting of high-risk areas for FoG based on both spatial and temporal factors, including a 3D data visualisation. Such a scenario shows the potential of the proposed framework to establish connections among various data fields across a diverse category of data. Furthermore, the results offer important insights for ground instability management and can potentially optimise the underground operation flow.

Nov 29, 2022

By A Rantala, J Timperi and J Kaartinen, T Maksimainen, O Haavisto

"X-ray fluorescence (XRF) is the most common technique used for online slurry assaying in base metal flotation applications. Typically, assays from feed, concentrate and tailings slurries are used to monitor and control the flotation circuit, with possible additional sampling locations in other main slurry flows inside the circuit. The elemental content detection from the XRF spectrum is relatively straightforward as the spectrum contains element-specific peaks whose height corresponds to the element concentration in the sample. However, centralised XRF analysers measure the elemental concentrations line-by-line, which may increase the sampling interval for an individual line and cause unnecessary response delays, especially in large flotation plants. Reflectance spectroscopy is an emerging technique that can be used to obtain more frequent measurements from slurries. The measurement is based on the mineral-specific absorbance of light in the visible and near-infrared (VNIR) wavelength range. Due to this relatively inexpensive and simple measurement system, it is possible to conduct the measurement simultaneously in several slurry lines. However, the information contained in the VNIR spectra is more difficult to interpret as concentrations of all the minerals in the sample contribute to the measured spectrum and changes in solids content, particle size and mineralogy disturb the elemental content estimation. Therefore, frequent calibration of the measurement is required. This study presents the application of combined reflectance spectrum and XRF measurements for rapid online slurry assaying in a copper-nickel flotation plant. The XRF assays are utilised as calibration samples for the reflectance spectrum measurement, keeping the calibration model up-to-date. The rapid reflectance spectrum analysis is then used to provide an almost continuous estimate of the slurry contents, enabling further improved process monitoring and control.Citation:Haavisto, O, Maksimainen, T, Rantala, A, Timperi, J and Kaartinen, J, 2016. Reflectance Spectroscopy with X-ray Fluorescence for Rapid Online Assaying in a Copper-nickel Flotation Plant, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

By F Sinaga, E Widijanto

PT Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. A review of the DOZ extraction bolting design was conducted in November 2000. The aim of this review was to re-evaluate the effectiveness of the current design in relation to bolt length and spacing and to challenge some questions about the technical background of the design. For instance, the influence of the rock condition on the design. To review this bolting design, several books and papers are reviewed and several experienced people have been contacted to give their opinion. The methodology used for this review is:reviewing the technical background of current design; collecting ideas and alternatives; collecting data from books and personal communication and conducting analysis; and conclusion and proposed design.

Jan 1, 2002

By K L. C Gontalves

In 1999, the Mineral Development Centre of CVRD (CDM) acquired a flotation device referred to as Mini Pilot Plant (MPP), which is able to run continuous flotation tests with drill core samples. Since then this equipment has been used to define the flotation circuit and process conditions during the pre-feasibility phase of CVRDÆs copper sulfide projects. Until now, the MPP results had not been validated for an industrial flotation operation. The present work consists of a comparison and correlation of the results from a flotation MPP and an industrial plant. In order to make this comparison, an industrial plant was completely sampled and the feed ore was tested on bench scale and on a MPP. The metallurgical and mass balances of each test were used for the comparison.

Jan 1, 2005

By D J. A Van Zyl, J C. Cunning

Technological advances associated with the expanded application of paste technology in underground mine backfilling are now stimulating an interest in the disposal of process tailings as paste in the surface environment. Concurrent with the development of alternative surface tailings disposal practices is the requirement to fully understand the consolidation behaviour of tailings in paste form, and to relate this understanding to the significant body of data and operating experience from decades of study of the performance of hydraulically placed tailings. One effective method for demonstrating the benefits derived from handling and placement of tailings as paste is to review tailings slurry consolidation theory from the perspective of the changes which take place in the material as it makes its transition from a loose slurry to a dense, stable deposit resulting from managed thin-layer deposition. For a typical process tailings, an example is provided which illustrates the effect which mechanical dewatering has in accelerating the consolidation process and thereby providing a range of benefits from the perspective of surface disposal. Increased rates of filling (rise), expanded use of upstream embankment construction methods and elimination of impounded surface solutions are some quantifiable benefits which can be assembled on a site-specific basis to allow for valid comparisons with more traditional approaches to tailings disposal.

Jan 1, 1998

A description is given of a detailed examination of a coal bore core and of attempts to predict properties of equivalent "as-mined" coal using the bore core data so obtained. The accuracy of the prediction was measured by testing independently a large sample of coal which was produced under near mining conditions from a site adjacent to the bore core. Very encouraging results were obtained particularly in the prediction of size and ash distributions and washability characteristics of run-of-mine Coal.

Jan 1, 1972

By M A. Tuck

Atmospheric air on a moisture free volume basis consists of approximately 21 per cent oxygen. The current minimum threshold for oxygen in Australia is 19.5 per cent. Atmospheric air generally will also contain water vapour and will also pick up further moisture as it flows around a mine ventilation network. This paper details the results of a study to determine how much oxygen depletion can occur due to the sole impact of increasing the moisture content of air and the potential impacts of this on ventilation system design. The study shows that the moisture content can have a significant impact on the oxygen concentration in mine air. The main factors controlling the impact are the barometric pressure, dry bulb temperature and relative humidity of the air.CITATION:Tuck, M A, 2015. What is the oxygen depletion potential of ?water vapour?, in Proceedings The Australian Mine Ventilation Conference, pp 173–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By B Crowdey, J Wall

The particular underground operation relating to this paper is a gold producer and has an orebody predominately consisting of rhyolite and marcasites pyrite. The ore has been identified as being reactive to nitrates.Operations currently utilise two twin boom Tamrock™ Super-Drill Jumbos for development mining. Capital (waste) headings have a nominal size of 7 m wide × 6 m high, while ore headings are designed at 5 m wide × 5 m high, with the lower reaches of the mine narrowing down to a 4.5 m × 5 m design. Production drilling is currently undertaken with an Atlas-Copco L6 Solo. Due to the reactivity of the ore, inhibited emulsion phase bulk explosives are used for all blasting activities, with electronic detonators utilised in the production sequence.Sublevel shrinkage stoping is utilised when the orebody is stronger than the host rock. After blasting the ore, and during extraction, the surrounding host rock cannot maintain integrity and it ‘collapses’ on top of the ore. Gravity forces this collapsing rock to follow the blasted ore through the drawpoints.The highest risk involved with sublevel shrinkage stoping is the necessity for charge crews to work upon ‘rills’ at the drawpoints, which are occasionally unstable, to charge the next blast ring to be fired. To overcome this issue a loading technique called ‘precharging’ is used whereby two to three rings are charged, but only the first ring is fired. This technique can minimise risks by taking the charge crew away from the rill and brow.As this mine contains hot and reactive ground, strict guidelines from the Australian Explosives Industry and Safety Group Inc (AEISG) are adhered to. These guidelines relate to the sleep time for the precharged rings.This paper describes the issues faced with precharging in hot and reactive ground, the monitoring required and the systems and procedures that were put in place to enable a successful outcome.CITATION:Crowdey, B and Wall, J, 2014. Precharging sublevel shrinkage production rings in hot and reactive ground with electronic blasting systems, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By V Shrotri L Muhmood, P Gandhre

The current work deals with the measurement of some thermophysical properties of Ca(NO3)2 based ternary nitrate molten salts as HTF (heat transfer fluid) / TES (Thermal Energy Storage) material for CSP (Concentrating solar power) plants. The density and viscosity of different compositions of the ternary salt mixture containing Ca(NO3)2, NaNO3 and KNO3 close to the liquidus has been experimentally measured. An attempt has also been made to measure the melting point of the salt using the cooling curve technique as well as Differential Scanning Calorimetry (DSC). Thermogravimetric analysis has also been performed to estimate the peak operating temperature of the salt. Compatibility of suitable pipe material (SS304) with molten salt has also been discussed. The salt mixture proves to be a viable alternative to the already existing HTFs like Therminol VP-1 (organic oil) or Solar Salt® in regards to its lower melting point, wider operating range, low cost, nontoxicity, sufficiently high density and comparable viscosity.

Jun 19, 2024