Search Documents

To help meet the challenge of mine finding at the start of the 21st century, the exploration geophysicist will have at his command a powerful range of tools, some new, some improved, and some which already exist today but are as yet little used. Remote sensing, using satellite and aircraft-based multi-spectral scanners, will provide the means for routinely mapping the surface distribution of certain carbonate rocks, clay and ferrous alteration minerals, based on the analysis of solar reflectance spectra. Time and emission-spectral resolved laser-induced fluorescence will likewise map the distribution of certain ore and pathfinder minerals, as well as certain skarn zones, all potentially related to ore deposits. The GPS (Global Positioning System), based on 18 orbitting satellites, will provide a universal, three dimensional, all weather navigation system which will completely supplant all existing aerial navigation systems, and greatly facilitate aerial surveying and automated processing and presentation of the data. Aeromagnetic gradiometer measurements will provide higher geometric resolution which will yield better definition of individual geological units. Multi-method ground geophysical surveys will be greatly expedited through the use of portable microcomputer-based, multi-sensor instruments. These instruments will interface with other intelligent devices for automated processing, presentation and interpretation of the ground field data. Borehole geophysics will come into more general use, both for at-hole measurements, especially using active nuclear techniques for grade determination, and for remote detection using a variety of electrical, magnetic, seismic and other methods.

Jan 1, 1986

From the mid-1970s ZC Mines at Broken Hill had a policy to increase ore production rates at progressively lower head grades. In the mid-1980s the mine suffered crippling losses at a time of low metal prices. An important contributory factor was the inherent geological distribution of metal grades in the seven defined ore lenses. Grades are bimodal, and perhaps, trimodal, in each ore lens. There is a tonnage deficiency in the critical cut-off grade zone of 7-10% Pb+Zn. Lowering the cut-off grade introduced siliceous and pyrrhotitic material which resulted in significantly poorer metallurgical performance. This example shows that the mine geologist needs to know the grade distribution of the orebody and to convey clearly the downstream implications of changes in the head grade.

Jan 1, 1990

The Lower Proterozoic metasediments of the Pine Creek Geosyncline form a chrono- stratigraphic sequence of mainly greenschist- and amphibolite-grade shallow-marine to supratidal pelites, psammites, carbonate rocks, and volcaniclastics which in places rests unconformably on Archaean basement. Granite and later dolerite intrude the sequence, and are associated with the major orogenic 1800-m.y. event which regionally metamorphosed the sediments. Most mineralisation is stratabound, and can be related at least partly to volcanic activity. Uranium mineralisation is mainly confined to particular carbonate-rich horizons near basement. Other metals are mainly in small hydrothermal deposits near intrusive granite. Specialist studies indicate that uranium was leached from its source rock, and probably carried as carbonate complexes in highly saline fluids at between 100 and 3500 C. Precipitation took place by redox reactions in breccia zones in carbonate rocks; these zones were formed by carbonate solution or diapiric movement of evaporites which preceded the carbonate. Extensive chloritisation in the ore zones suggests metasomatism by Fe- and Mg-rich fluids which may have evolved during dewatering of the evaporites. The main mineralising event took place after the 1800 m.y. metamorphism, and was probably

Jan 1, 1979

By Boyd D. M

Minor magnetic anomalies which may be un represented on a magnetic contour map can be extracted from the original survey data and plotted by the described method to provide a rapid interpretation of the magnetic survey, provided that the data has been recorded digi- tally on magnetic tape. The example used comes from 40 kilometers south of Charters Towers, Queensland.

Jan 1, 1977

By A Scott, I Onederra

A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful empirical or engineering models are currently available to blasting engineers and consultants, while more sophisticated approaches using mechanistic and numerical descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The fragmentation resulting from any blast will be heavily dependent on the properties of the rock mass being blasted; however, most empirical models rely on ‘rock factors’ generated from simple rock mass properties to describe the influence of the rock on the blasting outcome. In contrast, mechanistic models need explicit rock mass properties that require sophisticated laboratory measurements and detailed structural data if realistic outcomes are to be generated. The fragmentation modeller is caught between excessively simple rock mass descriptions for the empirical models and excessively complex data requirements for the mechanistic models.This paper briefly reviews the basis of a range of fragmentation models and the rock mass properties on which they rely. Shortcomings in the way that the mining industry tends to characterise the blasting properties of rock are discussed and some practical approaches are described to quantify these properties in both operating and greenfield mining environments. Case studies are presented where specific additional breakage properties and modelling features have been needed to generate a useful description of the fragmentation achieved.CITATION:Scott, A and Onederra, I, 2015. Characterising rock mass properties for fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 149–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The occurence of high silver values in the oxidised zone of the main lode at Broken Hill is well known as a large factor in achieving the early fame of Broken Hill, and the minerals of this zone form a long list, which has been tabulated by G Smith*, and includes...

Jan 1, 1926

By Sandvik

Fine grinding in an air-swept ball mill working in closed circuit with a forced vortex air classifier has been investigated first in continuous laboratory and then in industrial scale. Results from the laboratory circuit have shown significant influence of mill load (powder filling) on the capacity of the circuit. In laboratory scale the mill load was measured and controlled by a weighing platform placed under the complete mill set-up. The mill load of the industrial air-swept ball mill has till now been controlled by measuring the power consumption of the mill motor. Thus, it was necessary to operate far from the range of optimal mill filling. To improve the circuit performance, alternative ways of mill load measurement were investigated. An important factor was investment cost, as many fine grinding mills operate in relatively small circuits that do not wan-ant large investment. In this case the task was accomplished by using a piezoelectric strain transducer, which detected strain changes in the mill shell. It was installed in the midpoint of the shell, where the highest deformation was obtained. As the transducer was on the top position, it indicated compression, and on the bottom position it measured tension. By taking the difference between the readings, it was possible to calculate total strain variations, directly proportional to the mill load. The signal from the transducer was sent to a control room via a cordless infrared communication system, employing a microprocessor control card, which could further regulate other operating parameters of the circuit according to the software model. The installation required very low investment cost and provided simplicity of application as well as stability and reliability of characteristics under severe industrial condition. The measurement system made it possible to optimise the mill load and thus increase the production from 3.2 to 3.7 dh (15 per cent), and stabilise the circuit operation.

Jan 1, 1995

By Lovitt M

Ora Banda Gold Mine is located in the Eastern Goldfields of Western Australia. Mining is carried out underground by sublevel open sloping resulting in large open stopes. A Mass Blast of approximately 250 000 tonnes was carried out in July 1994 to recover a rib pillar between two stopes, and the crown pillar between the underground mine and the abandoned open pit above. Strategic development within 50 m of the blast consisted of two ventilation shafts and the main decline. This development required careful design and prediction of the blast results. This paper describes the design of the blast, the prediction of the likely effects, the measures taken to reduce the risk to important development, and the results of the blast.

Jan 1, 1995

By Favreau RF

Over the last 20 years the blasting industry has progressed from the stage of being artform to a science as it is today. The use of computers to simulate blasting results has allowed blasting engineers to accurately pre- dict blast results and to optimise their blasting. This paper describes the computer blast simulator called BLASPA and its various applications in blasting. BLASPA allows the blasting engineer to predict blast results given known details of explosive properties, their distribution, rock type and properties, hole size, burden, spacing, collar and subdrill. The simulator runs mathematical situations and outputs numerical estimates of fragmentation and muckpile results. The paper discusses results which show that the mathematical outputs correlate very closely with actual results seen in the field, thus confirming the validity of the simulator. BLASPA can be used to help improve blast design by predicting stress levels in the rock mass and consequent rock breakage.

Jan 1, 1986

By G J JAMESON

The flotation cell has undergone a number of changes since the process was first introduced in Broken Hill in the early years of this century. The development of the mechanical flotation cell is reviewed, followed by a discussion of more recent developments such as the flotation column, the air-sparged hydrocyclone, the Wemco-Leeds cell, the Bahr and Deister columns and the Jameson cell.

Jan 1, 1992

By B J. Hutchison, S Gannon, J Chambers, D Oko-oboh

The Kanmantoo copper mine is located in the Adelaide Hills area of South Australia and is owned and operated by Hillgrove Resources (HGO). The mine is a drill and blast, truck and shovel operation mining sulfide (chalcopyrite) ore located in chloritised andalusite biotite schist. The initial Kanmantoo open pit operation occurred in the 1970s, before falling copper prices closed the mine. In 2010 the mine was reopened by HGO and the Kavanagh cutback of the Kanmantoo pit was undertaken. The Spitfire, Nugent and Emily Star satellite pits were also mined through to 2015 before the latest steep wall Giant pit design was developed to take mining out to 2019.There are no major fault structures and only two significant shear zone structures exposed in the open pit walls. The main Garnet Andalusite Biotite Schist (GABS) unit is quite competent so the pit designs have therefore mainly been controlled by four distinct joint sets. This paper is a case study on the influence of the joint regime on the wall stability of the main GABS unit and how a better understanding of the joint regime and the use of rock reinforcement has allowed the steep wall design to be adopted.The paper also describes the remote geotechnical mapping and slope monitoring techniques used to manage the rockfall risks associated with the steep walled slope design.CITATION:Hutchison, B J, Chambers, J, Gannon, S and Oko-oboh, D, 2017. Case study of joint structure and the design and performance of open pit walls at the Kanmantoo copper mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 355–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

The mining of remnant coal reserves at the Liddell Open Cut is subject to a number of risks. These risks are of both a technical and financial nature. Liddell Open Cut is principally a conventional truck and shovel/loader operation, supplemented by a highwall coal augering operation. There are significant areas of divergence from more conventional operations including working in close proximity to a major dam, working up dip from an operating underground mine, and working through areas where there has previously been underground extraction. In addition the site has major long-term rehabilitation requirements. This paper, rather than concentrating on specific detail of areas of risk, presents the spectrum of geological, design, operational and post-mining risks that accrue to the various areas of activity in this open cut operation. The balance of this paper then provides an outline of the strategies employed by Liddell Coal to manage their potential impact.

Jan 1, 1994

Thirty six different commodities were recorded from 3708 mineral occurrences in the Atherton 1:250 000 Sheet area, mapped by personnel of the Queensland Department of Resource Industries. Tin, occurring in 56% of all mineral occurrences, is the most common, followed by copper, tungsten, silver, lead, gold, fluorite molybdenum, zinc and antimony. The densest area of mineral occurrences is the Herberton Mineral Field, one of the most intensively mined areas in the state.The majority of occurrences in the sheet area are fracture, fault or shear related vein or lenticular deposits, with subordinate types being pipe, skarn, endogreisen, disseminated and porphyry copper deposits. However the larger mines in the area are commonly of the subordinate types including the Red Dome gold-copper skarn, the Wolfram Camp and Bamford Hill tungsten- m olydbenum endogreisens, and the Vulcan pipe tin deposit. Significant gold prospects occur in quartz-antimony veins, breccia pipes and skarn deposits associated with rhyolitic porphyry dykes. A fluorite-gold association has been noted in several areas on the western side of the sheet.Mineralised fractures are predominantly oriented in a NNW direction which is the major trend in the Hodgkinson Province. Secondary N and NE directions are also present.

Jan 1, 1990

By Grano S. R, Kilgariff B

The Renisun Tin concentrator treats an ore containing I's per cent till as cassiterite and 22 per cent sulphur in a range of sulphide minerals. predominantly pyrrhotite. The sulphide minerals are removed by flotation using copper sulphate (CuS

Jan 1, 1997

By K Katov, S T. Ciutina, J D. Pyke

The development and optimisation of mill discharge trommels, and specifically their screen panels, can be a neglected area in the complex operation of a minerals processing plant. Trommels are often seen as a ‘set and forget’ component of the circuit, even when significant improvements in design are possible. A redesigned trommel and panel arrangement has simplified and added flexibility to the plant shutdown schedule at Kirkland Lake Gold’s Fosterville Gold Mine in Central Victoria.Prior to the trommel redesign, the shutdown frequency was determined by the expected life of trommel panels at 14 weeks. Planning downtime around this item led to higher maintenance costs and wastage in other areas of the plant. This was particularly disruptive with respect to mill lining change-outs, which were forced out of sequence and often changed prematurely. Fosterville Gold engaged Metso Australia Limited to propose a new trommel design that would better suit the site. The new trommel was engineered to balance simplicity with performance, and incorporated the latest in Modular trommel design, modelling and Finite Elemental Analysis (FEA). Modular Panels and Spiral Segments achieve significantly longer life, and allow in-situ panel change outs, flexibility in spiral and dam positioning and an improvement in classification performance. Trommel panel life has significantly increased from 14 to 71 weeks in the trommel’s highest wearing zone. The new design has eliminated some risks to safety by reducing manual labour and lifting requirements during shutdowns. There is greater flexibility with respect to shutdown requirements. The site is no longer at the mercy of trommel panel lifespan, which allows for better optimisation of wear components in the circuit. CITATION:Pyke, J D, Katov, K and Ciutina, S T, 2018. Modular SAG mill discharge trommel for maintenance flexibility and performance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By McGhie R. R

The general structural features and the principal mineral relationships of the Black Star ore body, Mount Isa, Queensland, have been described in several previously published papers. But particular reference may be made to the work of Grondijs and Schouten, whose examination of over 200 polished sections revealed some remarkable features in the process of ore deposition. The observations by the present authors are based upon the study of a smaller ·set of specimens complementary to those examined by Grondijs and Schouten and are intended to elaborate certain aspects of the mineral relationships, more particularly those affecting the ore-dressing processes.The work described applies to the primary sulphide ore only, and to the present milling practice of fine-grinding and selective flotation.GEOLOGICAL FEATURESThe Black Star is one of several economic mineral concentrations in the Mount Isa series of thinly bedded carbonaceous shales, which are considered to be of preCambrian age. The nlineralization is apparently connected with pegmatite intrustions located within some miles of the ore bodies, and has been Gontrolled in the main by major folding of the shales and by a shear system which follows approximately the strike and dip of the beds. The detailed "The investigations described in this paper were made in the Metallurgy Department, University of Melbourne, where the senior author was formerly Senior Lecturer in Mining and Metallurgy. A report on a section of the work was submitted by the junior author as a thesis requIred by the University of Queensland.

Jan 1, 1939

LITHOPROBE is a national, collaborative research grogram with the general objective of understanding the teotectonic evolution of the North American continent through multidisciplinary lithospheric studies in carefully selected areas of Canada. Six transect areas are investigating Precambrian evolution, although only in two of these is the research well evolved. The Archean Kapuskasing Structural Zone in Ontario is confirmed as an upthrust slice of upper to mid crust exposed at the surface. The Late Proterozoic Keweenawan mid-continent rift is shown to be the deepest known rift on Earth and the Grenville collisional zone of Ontario and Quebec involves crustal scale imbrication and ramping of deeply buried rocks to the surface. Two transect areas are investigating Phanerozoic evolution. In the Newfoundland Appalachians the geologically defined tectonostratigraphic domains do not coincide with lower crustal blocks defined by seismic reflection data. The Southern Cordillera Transect in western Canada is examining the nature, timing and dynamics of the assembly of the Cordillera, and particularly the role of accreted terranes. Work in the eastern and central segments has extended the known western limit of the North American craton at least IOO km westward and crustal-scale ramps associated with metamorphic core complexes have been identified.

Jan 1, 1990

By J G. McLellan, B Miller

Copper and Gold mineralisation at the Ernest Henry deposit is bound by two controlling shears along the hanging wall and footwall margins. The shear zone geometries have been influenced by a large diorite intrusion, dated at ca. 1660 Ma, which lies to the north-east and south-west of the main orebody. The shear zones, which partitioned strain prior to the main mineralising event ca. 1514–1504 Ma, and in conjunction with adjacent regional structures, have been a critical factor in the deposit location and geometry. Conventional exploration techniques have been utilised proximal to the current deposit since the initial discovery in order to expand upon known resources, with limited success. However, new geomechanical modelling techniques have now been employed to target structurally controlled mineralised zones in three dimensions. The main aim of the geomechanical modelling was to simulate the effects of regional deformation events to highlight areas of anomalous strain, which indicate areas with a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE-SW compression) to examine preconditioning of the system, and a D4 event (SE-NW compression) which have ultimately been responsible for the current location of the mineralisation.CITATION:McLellan, J G and Miller, B, 2017. Geomechanical modelling of the Ernest Henry iron oxide copper gold deposit – identifying fluid pathways to predict potential mineralised zones, in Proceedings Tenth International Mining Geology Conference 2017, pp 75–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017