Search Documents

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By S Maryati

Surface mining activities disturb large areas, produce great sediment loads and tend to be a source of water pollution if they are not managed properly. Coal mining in Indonesia has a very high risk of soil erosion because the coal mining areas are generally located in tropical areas with a high average of rainfall (4000 - 6000 mm/year) and use surface mining methods. The main factors affecting erosion risk are climate, soil type, topography, vegetation cover and management factors. Thus, the monitoring of erosion risk in mining areas is very important due to the characteristics of coal mining in Indonesia. The objective of this research is to determine the ability of satellite images (remote sensing data) and geographic information systems (GIS) to provide an accurate and up to date spatial database for the monitoring of erosion risk in surface coal mining areas using the Universal Soil Loss Equation (USLE) method.The erosion risk analysis and spatial data processing are generated by the ArcGIS 9.3 software and need several data, namely: an erosivity map, erodibility map, a slope map, vegetation index map and land management or land cover map. The erosivity map is derived from the rainfall data, whereas the erodibility map is derived from the soil map. The slope map is derived from the SRTM-DEM (Shuttle Radar Topography Mission-Digital Elevation Model) and processed using 3D analyst tools. Furthermore, the vegetation index map and land cover map are derived from a satellite image using digital image processing techniques.This preliminary study produced results that show soil erosion monitoring, which is integrated with remote sensing and GIS technologies, has great potential for producing accurate, advance, and low cost erosion risk maps in coal mining areas. This map is very important for getting spatial distributions of the erosion and useful for developing erosion management plans.

Nov 22, 2011

By D M. Brady

Underground coal mines in Australia have embraced the use of various inertisation techniques both proactively and reactively. The use of such techniques can have a significant influence on ratios and trends used to monitor the status of the underground environment. Whilst control strategies should never be ignored in favour of preserving the integrity of ratios, the influence and significance of the changes likely to be seen should be anticipated and understood for reliable interpretation of the situation. This paper looks at the influence inertisation techniques can have on results and subsequent interpretation.CITATION:Brady, D M, 2013. The influence of inertisation techniques on gas interpretation, in Proceedings The Australian Mine Ventilation Conference , pp 259-264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J Player, R de Vries, E Villaescusa, H Saw, R Hassell

The use of cemented rock fill (CRF) for support of open stope walls has increased in the Australian underground mines operations over the last five years due in part to its low capital cost. In open stoping the exposed CRF masses require adequate strength and stiffness, in order to resist the forces and to limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or from development mining waste sometimes up to 1 m in diameter. However, the use of waste rock, which has a poorly graded particle size distribution may not achieve the required minimum target strength due to segregation and large air voids within the fill mass. This paper describes the optimisation of CRF strength by either crushing the waste rock or the addition of sand to the mix. Both methods increase the level of fines in the mix design. Cylindrical samples having 400 mm diameter and 800 mm heights were prepared for uniaxial compressive strength (UCS) testing. The UCS test was determined using the Western Australian School of Mines (WASM) large-scale static test frame. The laboratory results were compared with a database of large-scale CRF strength mixed without sand from a number of mine sites around Australia. The comparison shows a significant strength development in the CRF mixing with addition of sand for a given cement percentage. Due to the higher strengths achieved by the addition of sand and the crushing of the waste material these CRF types require less cement to achieve the same strength. This has the potential to improve the overall economics of open stope mining due to less dilution of the exposed fill mass.CITATION:Saw, H, de Vries, R, Player, J, Hassell, R and Villaescusa, E, 2017. Optimisation of cemented rock fill strength for open stope support, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J F. C L Costa, J C. Koppe

It is recognised by the major international codes that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological and grade continuity, etc. However, the difficulty in quantifying the degree of uncertainty associated with mineral resources estimation has led to the creation of a large suite of methodologies, terms and definitions, with almost every mining company having its own set of standards. It is also intuitively known that several traditionally used methods to evaluate resources do not take into account the spatial continuity of the grades, being unable to provide a reliable measure of the error associated with their estimates. Since they do not provide an error assessment, these methods are inappropriate to assess local or global uncertainty associated with an estimate. Faced with these problems, this work aims at developing a methodology for either quantitative or qualitative analysis of mineral resources estimation, through incorporation of uncertainty and the correct definition of the associated risk or error. The proposed methodology includes the development of a software code incorporating all the main classification techniques used by the mineral industry. A comprehensive study about each technique was conducted allowing a comparison of the parameters affecting mineral inventory assessment. A case study was conducted with a typical iron ore deposit data set from the Conceitpo mine of the Itabira Complex in the Iron Quadrangle, Brazil. The results showed the specific limitations of each classification system and the influence in selecting their key parameters, always based on subjective choices.

Jan 1, 2009

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Day, I G. Robertson, G J. Lyman

"Various approaches are used in the industry for establishing procedures (sample mass estimation and method of subsampling) for sampling and analysis of gold ores. The key factors that determine the accuracy of the results that can be expected for a given set of procedures are widely misunderstood.Recent developments in sampling theory show that the estimation of the accuracy that can be expected for a given gold ore as a function of sample mass is actually a simple matter. For a given sample mass, the accuracy that will be achieved depends only on the grade of the ore and the range of masses of the grains of the gold in the ore. This, of course, demands that a reasonable estimate of the distribution or spread of gold grain masses in the ore be known. But this is something that should be known if the gold is to be efficiently recovered in the processing plant.This paper provides a simple explanation of the real facts about sampling of gold, either in the field or in the plant, and provides results for a number of cases of combinations of fine and coarse gold in an ore. The prerequisites for accurate gold sampling are:correct sampling with no loss of sample or contaminationsample preparation procedures that recognise the impact of the gold grain mass spreadpractical analysis of the sample masses required to provide acceptable accuracy.Issues of corporate governance are also discussed.Citation:Lyman, G J, Robertson, I G and Day, T, 2016. The Simple Facts about Sampling Gold Ores, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 159–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M S. Kizil, T OÆConnor

It is predicted that underground coal mines in the Bowen Basin will have a significant rise in heat problems as mines aim to increase production, depth of extraction and length of longwall panels. At an actual Bowen Basin mine, extended longwall panels greater than 4 km in length are planned to be mined at depths with a virgin rock temperature (VRT) of more than 40¦C. Research has been completed into the reasons for the substantial increase in temperature at the face for underground coal mines in the Bowen Basin. An analysis into heat loads produced at the Bowen Basin mine for the development and production phases shows a significant amount of additional cooling will be required to ensure safe working temperatures. All of the major sources of heat, which included both natural and mine induced heating, were considered for the analysis. Maximum heat loads were assessed, together with peak intake surface temperature to determine the maximum cooling capacity required at a Bowen Basin mine. These maximum heat loads were assessed for a specific longwall panel, Longwall A, which extends to over 4.1 km in length and at a maximum depth of over 330 m, resulting in a VRT above 40¦C. The cooling system positional efficiency was analysed, determining that underground cooling via an indirect heat exchanger was preferred to increasing the capacity of the current bulk air cooling (BAC) on the surface. A preliminary cost analysis was also detailed which compared the cost of additional BAC compared to implementing underground cooling.CITATION:OÆConnor, T, Kizil, M S and Belle, B, 2013. Required cooling system capacities for extended longwall panels at a Bowen Basin mine, in Proceedings The Australian Mine Ventilation Conference , pp 249-256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Corrosion affects the performance of rock support and reinforcement at various underground mines, including the George Fisher Mine, where recent studies showed that this risk to mining operations is generally not well understood. Corrosion reduces the capacity and life expectancy of ground support and generally is undetected unless the traditional destructive pull out test is employed to detect defect bolts. Where it is still acknowledged that the pull out test has still an important role to play in determining critical bond lengths for static and quasi static ground support designs, it does not provide an underground operation with any reassurance regarding its bolt's integrity, which has been compromised by in situ aggressive conditions. Non-destructive rock reinforcement calibration testing on single and twin strand cable bolts, rebar bolts and friction bolts at the George Fisher Mine enabled the testing team to detect bolts with compromised integrity in one area of the mine. The non-destructive rock reinforcement integrity testing conducted uses a complex 'Stress Wave Analysis' package based on the processing of clear seismic signals imparted into the rock reinforcement element that is being tested. The seismic signals are processed by 'Fourier Transform' into various criteria which can be used to produce models of the element such as mechanical admittance, frequency spectra and velocity which are all being used in the final modelling of the rock reinforcement element under analysis. This paper highlights the enormous potential to effectively manage the geotechnical risk that corrosion presents for an underground mining operation.

Nov 25, 2010

Proceeding from statistical data on the development of waste volume, an endeavour was made to characterise waste materials with regard to the applicability of treatments based on mineral processing. Many types of waste are characterised by a high heterogeneity. The separation processes used for processing raw minerals can also be used for separation of various waste mixtures. For some waste mixtures, differences in properties can be utilised for separation which are mostly less distinctive for raw minerals. State-of-the-art technology is illustrated with selected Examples.

Jan 1, 1993

By A G. Tomkins

"Approximately 32 per cent of the worldÆs total gold production has come from greenstone belts (Frimmel, 2008). In these regions numerous small to large, quartz vein-associated gold deposits are hosted in metamorphic rocks ranging from lower greenschist to granulite facies. Historical exploration has focused its efforts on rocks of greenschist to lower amphibolite facies because these seem to contain the most deposits. Consequently, these regions are now reaching mature brownfield status, particularly in developed nations, and finding new deposits is becoming progressively more difficult. In comparison, regions of similar tectonic setting, but instead containing high-grade metamorphic rocks of mid-amphibolite to granulite facies, have received little attention because the first explorers found fewer deposits there.However, these regions certainly do contain some very significant gold deposits such as Hemlo in Canada (~684 t Au), Renco in Zimbabwe (~31 t Au mined since 1980), the very profitable Challenger deposit in South Australia (~36 t Au; recovered + reserve + resource), and the most recently discovered Tropicana deposit in Western Australia (~182 t Au; reserve + resource). High-grade metamorphic terrains therefore offer explorationists an excellent opportunity to move onto relatively green fields within developed nations, which carry less risk associated with development. However, explorationists have comparatively little knowledge of the geological controls on gold distribution in high-grade terranes because: industry experience lies in traditional lode-style gold deposits these gold deposits are geologically more complex there has simply been minimal research conducted on these deposits as a holistic group.Furthermore, research conducted in the last five years has shown us that the previous widely accepted model for gold genesis in these terranes, the crustal continuum model, is incorrect. Here, I discuss features from several gold deposits hosted in high-grade metamorphic rocks and use these to define two categories for explorationists to consider: deposits that formed prior to peak metamorphism (metamorphosed gold deposits) deposits that formed well after peak metamorphism (post-metamorphic gold deposits). There are none that have been convincingly shown to have formed during peak metamorphism.CITATION:Tomkins, A G, 2013. Gold deposits in highly metamorphosed terranes, in Proceedings World Gold 2013, pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

This paper describes a detailed geostatistical study of producing copper orebodies at Mount Isa Mines Limited in Queensland, Australia. As a result of this work, kriging has been adopted for grade estimation for final stope design at Isa Mine. Extensive variogram and back analysis studies indicate that one relative variogram model can be used to give optimal kriged grade estimates from production sampling throughout the 100 million tonne copper orebody complex. The kriging method replaces a computer technique used at [sa Mine based on inverse distance weighting using parameters chosen from experience.Comparative stope designs based on 10 million tonnes of ore indicate a 16% increase in minable ore tonnage at a grade well above the cut-off, as a result of the geostatistical work.Although this paper is written as a practical description with simple explanations of geostatistical concepts, the theory and use of relative variograms has been expanded. A possible link is suggested between relative variograms and first order kinetics of natural mineral concentration processes.

Jan 1, 1982

By J M. Wallis

Heavy mineral sand exploration drilling prior to the 1970s generally utilised open hole auger and air-blast type drilling. However, mining reconciliations were poor and limitations on accuracy and precision of drilling results were severe.Working with the exploration companies, Wallis Drilling principals designed various systems, including what was termed the ‘Eneabba System’ and then the ‘Capel Twin-Tube System’. Eventually the company with its improvements developed and patented the Aircore Drilling System.Aircore drilling has subsequently become recognised as an excellent drilling system for exploration and mine-sample drilling that gives good precision and accuracy in sampling both above and below water. Its use has also been extended to many other commodities and is used in a number of overseas countries.This paper documents anecdotally the development of the system, identifying problems encountered during the times it was evolving and of the means to overcome the problems as being the documentation of the story by the inventors and developers in Wallis Drilling Company. Aircore drilling system is a Western Australian technological development owing its existence to the designing and incorporation of a number of discrete improvements along the way and recognises the tenacity and inventiveness of all who contributed to the system, in both Wallis and also in a number of companies that gave the impetus to succeed.

Oct 5, 2011

By T Purvis, Z Liu

Ernest Henry mine (EHM) is an underground sublevel caving mine located in north-west Queensland with a production rate of 6.4 Mt/a. The mine has sublevels spaced with a 25 m vertical interval. The production process on each level starts with the drilling and firing of a blind uphole rise to start the slot extraction. These rises are fired as a single shot and routinely need to achieve a design height of 22 m to 30 m depending on the local mine geometry. If the rise fails to perform as designed then the production phase of the level is delayed with significant rework required to remedy the situation.This paper describes the process that the EHM team has followed to improve the first time performance of each rise. The improvement process commenced with a review of results from previous rises and resulted in the identification of a number of improvement opportunities. A revised holistic approach was established for the process, which included involvement from operators and engineers. Through continued measurement and review of rise performance, inputs to the process were improved to a point where reliable results can now be expected. The successful performance of subsequent rises has been verified through a comprehensive quality assurance quality control (QA/QC) program. Before quality control processes were implemented, the success rate of blind uphole rises was only 11 per cent (one out of nine rises) at EHM. In comparison, the success rates have been vastly improved to 25 per cent (one out of four) and 75 per cent (three out of four) respectively following two stages of improvements. This paper concludes with the ‘current’ series of best practices used at EHM and recommendations.CITATION:Purvis, T and Liu, Z, 2017. Improving the performance of blind uphole rises at Ernest Henry Mine – a case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Norman TE

The design of composite materials for wear resistant service aims at com- bining two or more materials in such a way as to achieve unique and useful properties not generally available in any single homogeneous material. Properties and applications are presented of what might be described as a new generation of wear resistant materials, namely, metallic and part- metallic composites suitable for use in the high abrasion/moderate impact environment encountered in the crushing and screening of ore. Significant cost performance benefit can result from the use of such materials and several specific case histories are discussed. Some promising new developments, utilis- inn white iron and rubber, as yet in the field testing stage, are reviewed. Further comments are offered foreshadow- ing new composite developments, as yet untried but which appear to h,uve merit.

Jan 1, 1978

By W R. Adamson

Cerro Vanguardia SA (CVSA), property of AngloGold Ashanti, mines gold and silver from a system of vetiforme orebodies located in the south of the Argentine Patagonia, in the Province of Santa Cruz.Surface mining techniques are applied to develop a series of narrow pits with an average waste to ore ratio of 26:1. This quite unique constraint brings into focus the need to maximise inter-ramp and final wall angles, leading to a strong need to optimise wall control drilling and blasting in order to reduce back-break damage to an absolute minimum.The paper describes a program of applied investigation and design modification implemented during?2008?and?2009 in?two?separate pits of Cerro Vanguardia. Three distinct yet complementary damage mechanisms were identified and observed during the field components of the work; vibration induced strain fracturing, surface cratering around blasthole collars and quasi-static loading and unloading of the surrounding rock mass as a consequence of poorly controlled confinement.With these mechanisms identified, a measurement, modelling and modification campaign was conducted in order to reduce the incidence of each source of damage. Interactive design analysis and modelling, near-field vibration measurement, video capture and the application of electronic initiation technology were supported by seed wave modelling and topographic evaluation of the achieved results.Results point to the usefulness of simulation techniques for determining optimum delay timing to reduce vibration impact, while the visualisation of explosive energy distribution produced by drilling and explosive loading decisions assists in reducing the probability of over-confinement.This paper presents relevant aspects of the two fieldwork campaigns:1) describing the application of the techniques, and2) summarising the results obtained.

Nov 8, 2011

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011

By J Vann

Mineral Resource and Ore Reserve estimation is a challenging and demanding field, requiring application of professional knowledge, skill and experience of the highest order. If the many potential pitfalls are to be avoided, however, there are two other requirements which are of equal, if not greater, importance:good communication, and common sense. Estimation of Mineral Resources and particularly of Ore Reserves is almost always a team effort, involving a number of disciplines. Good teamwork requires good communication, both between team members and between the team and other parties having an interest in the process. Breakdown in these lines of communication can have far reaching effects on the project under consideration. The need to use common sense during a Resource or Reserve estimation exercise would seem to be self-evident. It is surprising, however, how often rigid adherence to procedures and methods prevails at the expense of clear thinking, usually with adverse and sometimes fatal effects on the project under consideration. This has become increasingly true as computerised methods have assumed a central role in Resource/Reserve estimation. The critical question that estimators should ask themselves at all stages of the process is: æIs what is being done sensible given the data available, what is known of this deposit and the purpose of the exercise?Æ

Jan 1, 1999

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974